Aquafin IC Details-12112018.pdf
13 Pages
496 KB
Download
<h1>Aquafin IC Details-12112018.pdf</h1> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>AQUAFIN-IC</p> <p>CEMENTITIOUS CRYSTALLINE PENETRATING WATERPROOFING <br />Typical Waterproofing Specifications</p> <p>Table of Contents:</p> <p>No.</p> <p>Waterproofing Specification</p> <p>Specification No.</p> <p>1 <br />2 <br />3 <br />5 <br />6 <br />7 <br />8 <br />9 <br />10 <br />11 <br />12 <br />13</p> <p>External waterproofing of below ground concrete wall & slab <br />Internal waterproofing of foundation concrete wall & slab - subject to ground moisture <br />Internal waterproofing of below ground concrete wall & slab - subject to hydrostatic pressure <br />Waterproofing of reservoir / wet well <br />Waterproofing of sewage tanks (clarifiers, digesters,filter basins, pumping stations, etc.) <br />Waterproofing of elevator, sump or other pits <br />Internal waterproofing of underground parking garage <br />Waterproofing of construction joints <br />Plugging water leaks <br />Typical sealing around pipe penetrations <br />Internal waterproofing of diaphragm/cut-off/slurry or secant pile walls <br />Internal waterproofing of below ground concrete wall - subject to hydrostatic pressure</p> <p>2.1.1 - 1 <br />2.1.1 - 2 <br />2.1.1 - 3 <br />2.1.1 - 5 <br />2.1.1 - 6 <br />2.1.1 - 7 <br />2.1.1 - 8 <br />2.1.1 - 9 <br />2.1.1 - 10 <br />2.1.1 - 11 <br />2.1.1 - 12 <br />2.1.1 - 13</p> <p>Note: These specification sketches have been prepared with our best knowledge and experience available at the time of publishing. As technology <br />advances and construction methods change we may have to update them. We therefore kindly ask the user to check the date on this page of this issue <br />and to re-check with us whether you have the latest edition. It is our goal to serve you and the construction industry as best as possible. <br />Copyright 2006, Aquafin, Inc. (Revision 06/06/08)</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 1</p> <p>Building <br />Product Systems</p> <p>EXTERNAL WATERPROOFING OF BELOW GROUND CONCRETE WALL & SLAB <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>///=///=///=///=///=</p> <p>3</p> <p>Waterstop <br />schematic</p> <p>1</p> <p>2</p> <p>Mud slab</p> <p>c “Sandwich application”: just prior to concrete pour, apply 1 coat AQUAFIN-IC in slurry or dry shake form at 2.25 lb/yd2 <br />(1.2 kg/m2) to prewatered mud slab or underlying concrete. (Refer to Guideline No. G-002)</p> <p>d Apply cove (seal strip) of AQUAFIN-MORTAR-IC at slab/wall joint. <br />e Apply AQUAFIN-IC to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each. <br />Total application = 2.5 - 2.8 lb/yd2 (1.5 kg/m2)</p> <p>AQ 10/06</p> <p>Specifier can consider use of AQUAFIN-IC ADMIX liquid crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 2</p> <p>Building <br />Product Systems</p> <p>INTERNAL WATERPROOFING OF FOUNDATION CONCRETE WALL & SLAB <br />SUBJECT TO GROUND MOISTURE <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>///=///=///=///=///=</p> <p>2</p> <p>1</p> <p>3</p> <p>Waterstop <br />schematic</p> <p>c Seal strip: Prime cavity with 1 coat AQUAFIN-IC slurry at 1.4 lb/yd2 (0.75 kg/m2) and while still fresh, fill flush to <br />surface with AQUAFIN MORTAR-IC.</p> <p>d Walls: Apply 1 coat AQUAFIN-IC slurry at 1.4 lb/yd2 (0.75 kg/m2). <br />e Slabs: Apply 1 coat AQUAFIN-IC slurry at 1.4 lb/yd2 (0.75 kg/m2). <br />Note: for basements being converted to offices or habitable areas that will receive carpeting, VCT, hardwood <br />flooring, or similar, install AQUAFIN VAPORTIGHT COAT-SG2 or SG3 vapor and moisture emission barrier in lieu of <br />AQUAFIN-IC if vapor emission exceeds 3 lbs/24 hrs•1000 ft2 (0.6 g/hr •m2) or >75% RH within the concrete.</p> <p>Refer to product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQ 05/08</p> <p>Note: In areas with poor drainage conditions or where high hydrostatic pressure is anticipated, apply a 2nd coat of <br />AQUAFIN-IC at the rate of 1.1 - 1.4 lb/yd2 (0.75 kg/m2). Apply second coat while first coat is still “green” (tacky). <br />Increase application rate for slabs to 2.0 lb/yd2 (1.0 kg/m2), applied in one coat. Refer to Specification No.2.1.1 - 3.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 3</p> <p>Building <br />Product Systems</p> <p>INTERNAL WATERPROOFING OF BELOW GROUND CONCRETE WALL & SLAB <br />SUBJECT TO HYDROSTATIC PRESSURE <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>///=///=///=///= <br />3</p> <p>2 <br />1 <br />Waterstop <br />schematic</p> <p>c In case of leaking wall/slab joint, install reglet (seal strip) of AQUAFIN MORTAR-IC. <br />Refer to Specification No. 2.1.1 - 9, Item 2.</p> <p>d Apply 1 coat AQUAFIN-IC to slab at 2.0 lb/yd2 (1.0 kg/m2). For new construction apply in dry shake form. <br />Note: for basements being converted to offices or habitable areas that will receive carpeting, VCT, hardwood <br />flooring, or similar, install AQUAFIN VAPORTIGHT COAT-SG2 or SG3 vapor and moisture emission barrier in <br />lieu of AQUAFIN-IC if vapor emission exceeds 3 lbs/24 hrs•1000 ft2 (0.6 g/hr •m2) or >75% RH within the <br />concrete.</p> <p>e Apply AQUAFIN-IC slurry to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each. Apply 2nd coat</p> <p>Specifier can consider use of AQUAFIN-IC ADMIX liquid crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQ 10/06</p> <p>while 1st coat is still “green” (tacky). Total application = 2.5 - 2.8 lb/yd2 (1.5 kg/m2)</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 5</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF RESERVOIR / WET WELL <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches <br />6 <br />5 <br />4</p> <p>3</p> <p>1</p> <p>2</p> <p>waterstop <br />schematic</p> <p>c Install cove of AQUAFIN MORTAR-IC to wall/slab joints (1 ½” x 1½” [38 x 38 mm]). <br />d Apply 1 coat AQUAFIN-IC slurry to slab at 2.0 lb/yd2 (1.0 kg/m2). <br />e Apply AQUAFIN-IC to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each. Apply 2nd coat while 1st coat is still <br />“green” (tacky). Total application = 2.5 - 2.8 lb/yd2 (1.5 kg/m2)</p> <p>f Corrosion protection: Apply 1 coat AQUAFIN-IC slurry to ceiling at 1.5 lb/yd2 (0.8 kg/m2). <br />g For covered structures, apply 1 coat of AQUAFIN-IC to roof slab at 2.8 lb/yd2 (1.5 kg/m2), or alternatively AQUAFIN-2K/M at <br />1/16” to 3/32” thickness, depending on overlaying strata conditions.</p> <p>h For exposed structures, new construction, apply 1-2 coats of AQUAFIN-2K/M to roof slab at 1/16” - 3/32” (1.5 - 2.4 mm). <br />For retrofit, apply AQUAFIN-2K/M as above or 1 coat AQUAFIN-IC at 2.0 - 2.8 lb/yd2 (1.0 - 1.5 kg/m2), depending on <br />circumstances.</p> <p>AQ 10/06</p> <p>Note: Old, heavily corroded tank walls can be re-coated with AQUAFIN-1K at 100 mils (2.5 mm) thickness in lieu of <br />AQUAFIN-IC. <br />Specifier can consider use of AQUAFIN-IC ADMIX liquid crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 6</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF SEWAGE TANKS <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />(Clarifiers, digesters, pumping stations, etc.) <br />Schematic sketches</p> <p>3</p> <p>1</p> <p>2</p> <p>1</p> <p>Waterstop <br />schematic</p> <p>c For added protection, install seal strip: Prime cavity with 1 coat AQUAFIN-IC slurry and while still fresh, fill flush to surface with <br />AQUAFIN MORTAR-IC. Alternative, install cove with MORTAR-IC.</p> <p>d Apply 1 coat AQUAFIN-IC slurry to slab at 2.8 lb/yd2 (1.5 kg/m2). <br />e Apply AQUAFIN-IC to vertical surfaces in 2 coats at 1.4 lb/yd2 (0.75 kg/m2) each. Apply 2nd coat while 1st coat is still “green” <br />(tacky). Total application = 2.8 lb/yd2 (1.5 kg/m2).</p> <p>Note: <br />a) Repair static cracks with AQUAFIN MORTAR-IC . <br />b) Repair dynamic cracks and/or joints with AQUAFIN JOINT SEALING TAPE-2000 or 2000-S. See Specification No. 1.1.3 - 15. <br />c) For above ground tanks subject to movement use AQUAFIN-2K/M lining in lieu of AQUAFIN-IC. See Specification No. 1.1.3 - 6. <br />d) Repair honeycombs, spalled and heavily corroded areas with MORTAR/LN prior to application of AQUAFIN-IC. <br />Above applications apply to environments not exposed to hydrogen sulfide environments and closed tanks with sufficient vents.</p> <p>AQ 10/06</p> <p>Specifier can consider use of AQUAFIN-IC ADMIX liquid crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>Waterproofing Specification <br />No. 2.1.1 - 7</p> <p>WATERPROOFING OF ELEVATOR, SUMP AND OTHER PITS <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>Waterstop <br />schematic</p> <p>2 <br />Concrete</p> <p>3 <br />1</p> <p>Waterstop <br />schematic</p> <p>c For leaking joints, or joints without a waterstop, install seal strips: Rout (cut) out reglet 1” x 1” (25 x 25 mm), prime <br />cavity with 1 coat AQUAFIN-IC slurry and while still fresh, fill flush to surface with AQUAFIN MORTAR-IC. <br />Note: Stop active leakage with AQUAFIN-PLUG-IC or FIX 10-S. If necessary use chemical grout injection.</p> <p>d Walls: apply AQUAFIN-IC to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each. Apply second coat <br />while first coat is still “green” (tacky). Total application = 2.5 - 2.8 lb/yd2 (1.5 kg/m2). <br />Note: Use AQUAFIN-1K for brick, rubble, cinder and CMU walls in lieu of AQUAFIN-IC.</p> <p>e Slab: apply 1 coat AQUAFIN-IC slurry at 2.0 lb/yd2 (1.0 kg/m2).</p> <p>AQ 10/06</p> <p>Specifier can consider use of AQUAFIN-IC ADMIX liquid crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 8</p> <p>Building <br />Product Systems</p> <p>INTERNAL WATERPROOFING OF UNDERGROUND PARKING GARAGE <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>/////////</p> <p>4</p> <p>3</p> <p>Concrete</p> <p>1 <br />2</p> <p>c Install AQUAFIN-IC to freshly poured slab in dry shake form at 2.0 lb/yd2 (1.0 kg/m2). (Consult Technical Guideline G001 for <br />details.)</p> <p>d Where waterstops are not installed or joint is leaking, rout out reglets along construction joints (1” x 1” [25 x 25 mm]). Prime <br />cavity with one coat AQUAFIN-IC and fill flush to surface with AQUAFIN-MORTAR-IC. <br />Note: Stop active leakage with AQUAFIN-PLUG-IC or FIX 10-S. If necessary use chemical grout injection.</p> <p>e Apply AQUAFIN-IC slurry to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each. <br />Total application = 2.5 - 2.8 lb/yd2 (1.5 kg/m2)</p> <p>Specifier can consider use of AQUAFIN-IC ADMIX liquid crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQ 10/06</p> <p>f Extend AQUAFIN-IC slurry in one coat at 2.0 lb/yd2 (1.0 kg/m2) approx. 2’ (0.6 m) beyond wall/floor and wall/ceiling joints.</p> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>Waterproofing Specification <br />No. 2.1.1 - 9</p> <p>WATERPROOFING OF CONSTRUCTION JOINTS <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>1</p> <p>2</p> <p>3</p> <p>4</p> <p>The following alternative methods can be used where standard water stops cannot be installed or where additional <br />waterproofing protection is desired:</p> <p>c Apply 1 coat AQUAFIN-IC slurry at 2 lb /yd2 (1.0 kg /m2) to joint surface prior to pouring connecting section. <br />d Reglet (seal strip) 1” x 1” (25 x 25 mm): prime cavity with 1 coat AQUAFIN-IC slurry at 1.4 lb /yd2 (0.75 kg /m2) and fill flush to <br />surface with AQUAFIN MORTAR-IC, approx. 1.0 lb/ft (1.3 kg/m).</p> <p>e Install cove (seal strip) 1.5” x 1.5” (38 x 38 mm) of AQUAFIN-MORTAR-IC, approx. 1.0 lb/ft (1.3 kg/m) at slab/wall joint. <br />f Apply 1 coat AQUAFIN-IC slurry at 2 lb /yd2 (1.0 kg /m2) to joint surface prior to pouring connecting section, or if this is not <br />feasible, rout out reglet(1” x 2” [25 x 50 mm]), prime cavity with 1 coat AQUAFIN-IC slurry at 1.4 lb /yd2 (0.75 kg /m2) and fill <br />flush to surface with AQUAFIN MORTAR-IC approx. 2.0 lb/ft (2.6 kg/m).</p> <p>AQ 11/01</p> <p>Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>Waterproofing Specification <br />No. 2.1.1 - 10</p> <p>PLUGGING WATER LEAKS <br />Schematic sketches</p> <p>1</p> <p>4</p> <p>2</p> <p>5</p> <p>3</p> <p>6</p> <p>c Locate source of leakage in the concrete. <br />d Rout out the leak in a U-shaped configuration to sound concrete, minimum 2” (50 mm) deep and 1” (25 mm) wide. Clean cavity <br />and remove any excess water.</p> <p>e Form a plug with AQUAFIN-PLUG-IC or AQUAFIN FIX 10-S and press this into the cavity, filling to approx. 1” depth. Hold this in <br />place for about 30 - 60 seconds, until it has set. In case of a strong water flow, insert a drain (i.e. 3/8” - 1/2” clear plastic pipe) <br />into the cavity immediately before inserting the PLUG-IC or FIX 10-S.</p> <p>f When plug is fully hardened and leakage has stopped, remove any excess material and prime remaining cavity with one slurry <br />coat of AQUAFIN-IC.</p> <p>g While slurry is still moist (“green”) fill cavity flush to surface with AQUAFIN MORTAR-IC. Where a drain has been used, carefully <br />remove drain soonest next day, or when mortar has reached at least 2/3 of its final strength, and plug the remaining hole as <br />described above.</p> <p>h When mortar has set, apply surface waterproofing (AQUAFIN-IC, AQUAFIN-1K or AQUAFIN-2K/M) over concrete surface.</p> <p>AQ 10/06</p> <p>Refer to product data sheets for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 11</p> <p>Building <br />Product Systems</p> <p>TYPICAL SEALING AROUND PIPE PENETRATIONS <br />AQUAFIN-IC <br />Schematic sketches <br />A. Sealing around steel or concrete pipes</p> <p>Rout out 1" x 1" triangular reglet, and <br />fill cavity with MORTAR-IC.</p> <p>Steel or concrete pipe</p> <p>Apply AQUAFIN-IC <br />surface waterproofing</p> <p>B. Sealing around PVC pipes</p> <p>B.1</p> <p>B.1: Small pipes (6" and 6" ) <br />Install cove of MORTAR-LN or IC at pipe penetration. <br />Apply AQUAFIN-2K/M surface waterproofing, <br />extending 6" (15 cm) onto pipe. <br />Ckeck possibility of using AQUAFIN SEALING <br />GASKET-18/18 or 2K-FABRIC.</p> <p>Note: Mechanically roughen PVC surface and degrease/clean with isopropanol or aceton prior to application <br />of AQUAFIN-2K/M. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQ 11/01</p> <p>B.2</p> <p>Gasket size: 18" x 18" (450 x 450 mm) <br />can be cut to required size and shape</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 12</p> <p>Building <br />Product Systems</p> <p>INTERNAL WATERPROOFING OF DIAPHRAGM OR SECANT PILE WALLS <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches <br />Ground level</p> <p>///////// <br />3</p> <p>Soil</p> <p>DIAPHRAGM or SECANT PILE WALL</p> <p>4</p> <p>Intermediate slab</p> <p>4 <br />3 <br />1</p> <p>2 <br />3</p> <p>Foundation mat <br />Mud slab <br />Swellable (hydrophilic) waterstop <br />(by others)</p> <p>0</p> <p>b Install underslab waterproofing membrane by others, or AQUAFIN-IC at 2.25 - 2.8 lb/yd2 (1.2 - 1.5 kg/m2) over mud slab. <br />c Install AQUAFIN-IC to freshly poured slab in dry-shake form at 2.0 lb/yd2 (1.0 kg/m2). (Consult Technical Guideline G001.) <br />d Where waterstops are not installed or joint is leaking, rout out reglets along construction joints (1 - 2” x 1 - 2” [25 - 50 x 25 - 50 <br />mm]). Stop active leakage with AQUAFIN-PLUG-IC, prime remaining cavity with AQUAFIN-IC and fill flush to surface with <br />AQUAFIN-MORTAR-IC. Where necessary use chemical grout injection.</p> <p>e Apply AQUAFIN-IC slurry to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each (total 2.5 - 2.8 lb/yd2 (1.5 kg/m2)). <br />f Extend AQUAFIN-IC slurry in one coat at 2.0 lb/yd2 (1.0 kg/m2) approx. 2’ (0.6 m) beyond wall/floor and wall/ceiling joints. <br />AQUAFIN MORTAR-IC as per Waterproofing Specification No. 2.1.1-9, item (4). <br />Alternative to (0) and (1): Add AQUAFIN-IC ADMIX liquid crystalline waterproofing admix to the concrete during batching. <br />Refer to standard specifications and various product data sheets for further information. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQ 10/06</p> <p>g Seal leaking vertical construction joints with AQUAFIN MORTAR-LN. Seal horizontal construction joints in foundation mat with</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 2.1.1 - 13</p> <p>Building <br />Product Systems</p> <p>INTERNAL WATERPROOFING OF BELOW GROUND CONCRETE WALL <br />SUBJECT TO HYDROSTATIC PRESSURE <br />AQUAFIN-IC CRYSTALLINE WATERPROOFING <br />Schematic sketches</p> <p>///=///=///=///= <br />3</p> <p>1 <br />Waterstop <br />schematic</p> <p>c In case of leaking wall/slab joint, install reglet (seal strip) of AQUAFIN MORTAR-IC. <br />Refer to Specification No.2.1.1 - 9, Item 2.</p> <p>e Apply AQUAFIN-IC slurry to vertical surfaces in 2 coats at 1.25 - 1.4 lb/yd2 (0.75 kg/m2) each. Apply <br />2nd coat while 1st coat is still “green” (tacky). Total application = 2.5 - 2.8 lb/yd2 (1.5 kg/m2)</p> <p>AQ 10/06</p> <p>Refer to standard specifications and various product data sheets for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p>
