TDS-InjectProECO-Polygel_93019.pdf
2 Pages
413 KB
Download
<h1>TDS-InjectProECO-Polygel_93019.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectProECO-Polygel</p> <p>Hydrophilic, flexible polyurethane grout for stopping active water leaks <br />CSI Div. 03 <br />03 64 00 Injection Grouting <br />Product Description: <br />InjectProECO-Polygel is a solvent-free, polyurethane injection grout designed <br />to react with added water to produce an impermeable foam or elastomeric <br />soft gel. <br />Typical Applications: <br />Any concrete structure with heavy water leaks such as <br />• Water retaining/storage structures <br />• Concrete Dams <br />• Tunnels <br />• Manholes <br />• Expansion joints <br />Reaction Times: <br />Gel:Water </p> <p>Cream Time</p> <p>Gel Time</p> <p>End Product</p> <p>1:1</p> <p>20-30 sec</p> <p>50-60 sec</p> <p>Strong foam</p> <p>1:5</p> <p>45 sec</p> <p>Strong gel</p> <p>1:10</p> <p>80 sec</p> <p>Gel</p> <p>1:15</p> <p>180 sec</p> <p>Soft gel</p> <p>Installation Procedures: <br />Refer to Aquafin InjectPro Grouting Guide for full instructions. <br />InjectProECO-Polygel is injected with a two-component pump with water as <br />the second component. Polygel only needs water to achieve the final foam <br />or gel, to control the reaction speed and to flush the machine. <br />• Heavy water leakages <br />Because of the high reactivity in combination with water, InjectProECOPolygel is used for shutting off heavy water leakages (up to 5 m³ per <br />minute). The ratio to be used is 1:1 or pure resin. <br />• Expansion joints <br />InjectProECO-Polygel can be used in expansion joints because of the <br />foaming capability and good flexibility of the end product as well as a <br />good adhesion to the aggregate. The ratio to be used: InjectProECOPolygel to water 1:4 or 1:5. <br />• Gel membrane/screen injection <br />Because of the low viscosity of the water/polymer mixture, it can be <br />used as a liquid but solidifying gel membrane applied to the positive <br />side of a concrete structure from the negative side; ratio to be used <br />InjectProECO-Polygel to water 1:10. The gel mixture will fill the voids from <br />the aggregates (like sand etc.) behind the wall to avoid that water will <br />come into the wall construction. The procedure is drilling through the wall <br />and pumping the Polygel water mixture via packers. <br />• Masonry walls/screen injection <br />Because of the low viscosity in combination with a relatively long pot life <br />the Polygel can be used in masonry walls as a vertical barrier to fill the <br />voids/joints in masonry walls to avoid that water comes through the voids <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Physical Properties</p> <p>InjectProECO-Polygel</p> <p>Color</p> <p>Clear Yellow</p> <p>Specific Gravity</p> <p>1.04 g/cc</p> <p>Viscosity @ 25°C (77°F)</p> <p>1366 cps</p> <p>Shelf Life</p> <p>18 months</p> <p>to the surface of the wall. Ratio to be used Polygel to water 1:12/13. <br />The procedure is drilling holes to 80 % of the wall thickness or until 5 <br />cm from the back of the wall and pumping the Polygel-water mixture via <br />packers in the wall. <br />• Gel encapsulation <br />Because of the low viscosity in combination with a good adhesion Polygel <br />can be used for the gel encapsulation method where voids are filled with <br />a jelly material (e.g. delaminated concrete slabs etc.). The ratio to be used <br />Polygel to water 1:10. <br />• Oakum technique <br />Because of the reactivity with water the Polygel can be used for the <br />activated oakum technique where oakum or any other kind of carrier <br />material is soaked in purePolygel. The oakum and the Polygel are applied <br />into any void where small water leakages can be a problem (pipe outlet <br />through walls etc.). <br />• Injection hoses <br />Because of the low viscosity in combination with a relatively long pot <br />life the Polygel can be used for injection hoses being installed in new <br />structures for immediate waterproofing or for later waterproofing. The ratio <br />to be used Polygel to water 1:12/13. <br />Packaging: <br />InjectProECO-Polygel: 5 gallon pails <br />Storage & Shelf Life: <br />2 years when stored properly in unopened original container. Product is <br />highly moisture sensitive. Store in original sealed containers at temperature <br />between 60°F – 90°F. Opened containers must be handled properly to <br />prevent moisture contamination. <br />Limitations: <br />• Temperature significantly affects viscosity. Protect material from excessive <br />heating and cooling prior to grouting to avoid affecting viscosity. <br />• If using water baths to cool or heat pails avoid splashes to prevent water <br />coming in direct contact with resin - this will activate the reaction. <br />• Do not warm material or packaging above 90°F. <br />• Do not reseal containers of contaminated materials as it can create <br />pressure. <br />• Clean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material such as <br />clay or vermiculite and transfer to metal waste containers. Wash area with <br />decontamination solution (5-10% solution of sodium carbonate). Dispose <br />of waste in accordance with federal, state and local regulations. <br />Page 1 of 2</p> <p>(09/30/19 EK-BE)</p> <p>InjectProECO-Polygel <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and not <br />for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. After <br />contact with skin, wash with plenty of water. In case of eye contact, rinse <br />immediately with plenty of water for 15 minutes and seek medical advice. <br />KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period <br />of one year from the date of installation to be manufactured free of defects <br />and to be consistent with its technical properties as stated in our current <br />Technical Data Sheet. This product must be used as directed and within its <br />stated shelf life. AQUAFIN INC. will replace or at our discretion refund the <br />purchase price of any product, excluding cost of labor, which is proven to be <br />defective. Our product recommendations are based on industry standards <br />and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or <br />use of the product. AQUAFIN INC. MAKES NO WARRANTY AS TO <br />MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND <br />THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS <br />OR IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort <br />including remote or consequential damages, down time, or delay. Any <br />claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase. <br />For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(09/30/19 EK-BE)</p>
