55 AQUAFIN-SLU-PRIMER-042413.pdf
1 Page
65.1 KB
Download
<h1>55 AQUAFIN-SLU-PRIMER-042413.pdf</h1> <p>SLU-PRIMER <br />High Performance Primer for <br />Porous and Non-porous <br />Substrates <br />† Zero VOC (0 g/L) - water based - non flammable <br />† Qualifies for LEED credits <br />† Rapid drying <br />† Excellent bond <br />Product Description <br />AQUAFIN®-SLU-PRIMER is a water based, V.O.C. free, one component acrylic latex resin that improves the adhesion of cementitious self-leveling underlayment’s or topping materials. Applied <br />over standard absorbent or non-absorbent substrates, such as <br />AQUAFIN-”SG3” moisture mitigation, terrazzo, marble, metal <br />decking, ceramic and quarry tile.</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials*…………………. Up to 2 points <br />IEQ Credit 4.2, Low-Emitting Materials <br />Paints and Coatings …………………….…1 point <br />* Using this AQUAFIN product helps contribute to LEED certification of projects in the categories shown above.</p> <p>Typical Applications <br />SLU-PRIMER can be applied over: <br />A. absorbent cementitious substrates. <br />B. non-absorbent substrates, such as: <br /> AQUAFIN-”SG3” epoxy moisture vapor reduction system or <br />similar; <br /> Terrazzo; Marble; Metal decking; Quarry and Ceramic tile; <br />prior to application of cementitious underlayment's, topping materials or separation screeds.</p> <p>Substrate Preparation</p> <p>Mixing & Application <br /> Pre-condition cooler containers</p> <p>505 Blue Ball Road, # 160 <br />Phone (410) 392-2300</p> <p> <br /></p> <p></p> <p>Absorbent substrates: apply even coat of primer, working it <br />into the substrate with a push broom or brush. Do not use a <br />roller to apply. Additional coats may be required over extremely porous concrete and to prevent substrate outgassing. Broom <br />out any puddles of primer. <br />Non-absorbent substrates (i.e. AQUAFIN-”SG3”): apply a <br />thin, even coat of primer to the substrate using a non-shed <br />short-nap roller. Do not spray, broom, or mop apply. <br />Install self-leveling underlayment’s, topping materials or separation screeds after SLU-PRIMER has turned to a transparent <br />film (with no milky spots) after approximately 1 - 3 hours. Maximum wait time from initial application is 24 hrs. <br />If SLU-PRIMER sits for more than 24 hrs, re-apply a second <br />coat and install underlayment within correct application window. If application window is missed again, remove primer <br />mechanically and start the installation on clean substrate.</p> <p>Coverage:</p> <p>400 - 600 SF/gal (9.8 - 14.7 m2/L), depending on surface profile.</p> <p>Drying Time:</p> <p>About 1 – 3 hours.</p> <p>Clean Up: <br />Clean tools and equipment with water immediately after use. <br />Cured material can only be removed mechanically.</p> <p>Packaging: <br />2.5 and 5 gal (9.5 and 18.9 L) plastic pails. <br />264 gal (1000 L) tote. (Heavy-duty intermediate bulk container (IBC)). <br />One year in unopened container. Store in a cool, dry area and <br />keep from freezing. Do not expose container to sun.</p> <p>Note: <br /> Prior application of SLU-PRIMER, a test area is highly recom <br /></p> <p>mended insuring suitability for intended use. <br />Low substrate temperatures and/or high ambient humidity <br />lengthen drying time, whereas higher temperatures and low <br />humidity shorten drying time of SLU-PRIMER. <br />Once cured, mixed product presents no ecological risk.</p> <p>Safety: Refer to MSDS (Material safety Data Sheet). Contains <br />no hazardous materials. Use rubber gloves and goggles during mixing <br />and application. Avoid contact with eyes and skin. After contact with <br />skin, wash with plenty of water. In case of eye contact, rinse immediately with plenty of water and seek medical advice. In case of handling <br />large quantities, provide good ventilation if indoors. <br />KEEP OUT OF REACH OF CHILDREN.</p> <p>to minimum 65oF (18oC) to</p> <p>allow uniform mixing. <br />Plastic pail: remove lid and stir mix thoroughly for approximately 3 minutes to a homogenous mix, using a slow speed (300 500 rpm) mechanical mixer (“jiffy” mixing paddle). <br />Tote: remove top cover and stir mix thoroughly to a homogenous mix, using an appropriate slow speed (300 - 400 rpm) <br />long shaft mechanical mixer with one or two mixing cages.</p> <p>AQUAFIN, Inc.</p> <p></p> <p>Do not apply SLU-PRIMER at room or substrate temperature <br />below 50oF (10oC) or maximum 95oF (35oC). Maintain temperature range for minimum 72 hours after applying SLU-PRIMER <br />and finished material. Use indirect auxiliary heaters to maintain <br />minimum temperatures in cooler conditions.</p> <p>DISTRIBUTED BY: <br />Elkton, MD 21921</p> <p>Fax (410) 392-2324</p> <p>TOLL FREE 1 - 866 - AQUAFIN (1-866-278-2346)</p> <p>For commercial use only!</p> <p>LIMITED WARRANTY: AQUAFIN, INC. warrants its products to be manufactured free of <br />defects for one year and to be consistent with its standard high quality. We will replace or, at <br />our election, refund the purchase price of, any product which is proven to be defective, provided that the product was properly applied. Our product recommendations are based on Industry <br />Standards and testing procedures. We assume no warranties either written, expressed or <br />implied as to any specific methods of application or use of the product. AQUAFIN, INC. <br />MAKES NO WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR <br />PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR <br />IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. User shall determine the suitability of the product <br />for his intended use and assume all risks and liability in connection therewith.</p> <p>E-mail: info@aquafin.net <br />http://www.aquafin.us <br />CHECK WEBSITE FOR LATEST UP-DATES</p> <p>(Up-date 04/24/13)</p> <p>B. AQUAFIN-”SG3”: <br />1. Install “SG3” as per “SG3” data sheet and let cure for minimum <br />12 hours at 73oF (23oC) before applying SLU-PRIMER.</p> <p></p> <p></p> <p>Shelf Life & Storage:</p> <p>A. Concrete: <br />1. All cementitious substrates must be sound, dimensionally stable, clean, free from voids, oil, wax, grease, paint, gypsum <br />compounds, loose debris and toppings and any other contaminant that might act as a bond breaker. <br />2. Pay particular attention to sufficiently mechanically roughen <br />cementitious substrates to ICRI CSP 3 or greater profile. Use <br />steel shot blasting, wet or dry sand blasting, diamond-grinding <br />or other engineer approved methods. <br />3. Remove all dirt and dust by vacuuming. <br />4. Repair holes, defects, irregular surfaces, weak mortar joints, <br />etc. with MORTAR-LN or MORTAR-40 (fast setting).</p> <p></p> <p>Application: <br /> SLU-PRIMER is milky when wet and clear when dry.</p>
