SAFETY DATA SHEET SDS No. I.SF.2
IDENTITY: InjectPro-SuperFast: Component-B Date prepared: Date revised:
MAY 2015 MARCH 2019
SDS No. I.SF.2
Section 1 – Product Identification IDENTITY:
InjectPro-SuperFast Component-B
Product Name:
Product Use Description:
Polyurethane Injection Grout
AQUAFIN, INC. 505 BLUE BALL RD. #160 ELKTON, MD 21921
24 hr Emergency Phone: Chem-Tel
Recommended use of the chemical and restriction on use:
Refer to the product technical data sheet. For industrial and professional users.
Information Phone No.
(800) 255-3924 (410) 392-2300
www.aquafin.net info@aquafin.net
Section 2 – Hazards Identification GHS Classification: Skin irritation, Category 2 Serious eye damage, Category 1 Specific target organ toxicity, repeated exposure, Category 2
= H315. = H318. = H373.
GHS Label element: Hazard Pictograms GHS05
GHS08
Signal Word:
Danger
Hazard Statements: H315: H318: H373:
Causes skin irritation. Causes serious eye damage. May cause damage to respiratory system through prolonged or repeated exposure.
Precautionary Statements: Prevention: P102: Keep out of reach of children. P260: Do not breathe mist, vapours or spray. P264: Wash skin thoroughly after handling. P270: Do not eat, drink or smoke when using this product. Wear protective gloves/protective clothing/eye protection/face protection. P280: Response: P302 + P352: P332 + P313: P362: P305 + P351 + P338: P337 + P313 P310: P314:
IF ON SKIN:
Wash with plenty of soap and water. IF SKIN irritation occurs, get medical attention. Take off contaminated clothing and wash before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF eye irritation persists, get medical advice/attention. Immediately call a POISON CENTER or physician. Get medical attention if you feel unwell.
Page 1 of 5
SAFETY DATA SHEET IDENTITY:
InjectPro-Superfast B-Component
Storage: P403 + P410:
Store in a well-ventilated place. Protect from sunlight.
Disposal: P501:
Dispose of contents/container to an approved waste disposal site.
Section 3 – Composition / Information on Hazardous Ingredients CAS No.
Component: Non-hazardous polyether polyols Diethylene glycol Pentamethyldiethylenetriamine
111-46-6 3030-47-5
% (Weight) 50 - 70 ≤5 ≤4
Note: There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
Section 4 – First Aid Measures Inhalation:
Supply fresh air and consult a physician if breathing becomes difficult. Symptoms may be delayed for several hours.
Ingestion:
If person is conscious, wash out mouth with water. Do not induce vomiting unless instructed to do so by a poison center or physician.
Skin Contact:
Immediately flush skin with plenty of water. Do not use solvents or thinners. Remove contaminated clothing and shoes. Seek medical advice if irritation or rash occurs. Wash clothing before reuse.
Eye Contact:
Immediately flush eyes with plenty of water for at least 15 minutes, lifting upper and lower eyelids occasionally. Remove contact lenses, if present. Seek medical attention if irritation persists.
Section 5 – Fire Fighting Measures Extinguishing Media:
Water spray, foam, dry chemical or carbon dioxide.
Fire Fighting Procedures:
Standard. As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear. Containers can build up pressure if exposed to heat (fire). Cool with water spray. Do not scatter material with high pressure water streams.
Hazardous Combustion Products:
Carbon oxides, nitrogen oxides, and various hydrocarbons.
Section 6 – Accidental Release Measures Person-related Safety Precautions:
Provide plenty of fresh air. Avoid eye and skin contact. Avoid inhalation of vapors. Wear personal protective equipment. Remove or eliminate all ignition sources.
Methods for cleaning-up:
Prevent from entering into soil, ditches, sewers, waterways and/or groundwater. Small spills: Absorb with dry chemical absorbent, earth, Page 2 of 5
InjectPro-SuperFast: B-Component
sand or any other inert material. Clean spill area with detergent and water. Retain water for disposal. Waste Disposal Method:
Dispose in accordance with local, state and federal regulations.
Ecological Information:
Do not allow product to reach ground water, bodies of water, or storm water or sewage systems.
Section 7 – Handling and Storage Handling:
Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Follow all SDS/label precautions even after the container is emptied because it may retain product residues. Use only with adequate ventilation. Keep container closed when not in use. Do not reseal if contaminated. Keep away from heat and flame.
Storage:
Keep container tightly closed when not in use. Do not store in direct sunlight.
Storage Temperature:
4oC – 32oC (~40oF - ~90oF).
Section 8 – Exposure Controls / Personal Protection Engineering Controls:
Use adequate ventilation.
Skin Protection:
Wear chemical resistant protective clothing and footwear impervious to the product if there is a potential for skin contact.
Hand Protection:
Glove(s): neoprene.
Eye Protection:
Use safety goggles or face shield.
Work/Hygienic Practices:
Wash hands before breaks and after work, and before eating, drinking or smoking.
Section 9 – Physical and Chemical Properties Physical state: Color: Odor: Solubility in water: Boiling point: Flash point: Vapor Pressure: Flammability: Specific Gravity (water = 1) at 25oC: Viscosity, (kinematic) at 25oC: Auto ignition Temperature: Lower explosion Limit: Upper explosion Limit:
Liquid Various colors Slightly musty Insoluble, reacts with water No data >93°C (>200°F) (closed cup) No data No data 1.12 – 1.14 g/cm3 1500 - 2000 cps No data available No data available No data available
Section 10 – Stability and Reactivity Stability:
Stable.
Hazardous Decomposition Products: Carbon oxides, nitrogen oxides and various hydrocarbons. Page 3 of 5
Hazardous Polymerization:
Will not occur.
Incompatibilities:
Strong acids, bases and oxidizers.
Section 11 – Toxicological Information Acute toxicity: Diethylene glycol
Pentamethyldiethylenetriamine
Dermal: Oral: Inhalation:
LD50 LD50 LC50
11890 mg/kg (rabbit). 12565 mg/kg (rat). > 4.4 mg/L/4 h (rat).
280 mg/kg 1630 mg/kg 290 mg/L/6 h
(rabbit). (rat). (rat).
Carcinogenity: IARC: Not regulated as a carcinogen. NTP: Not regulated as a carcinogen. OSHA: Not regulated as a carcinogen.
Section 12 – Ecological Information Ecotoxicological Information:
Diethylene glycol LC50 Pentamethyldiethylenetriamine LC50
>32,000 mg/L/96h (fish) >22 mg/L/96h (golden orfe)
EC50 EC50
>84,770 mg/L/48 h (daphnia). >76 mg/L/48 h (daphnia).
Section 13 – Disposal Considerations Product waste:
Must be disposed of in a manner consistent with federal, state and local regulations.
Empty Container:
when cartridge is empty dispose with trash.
RCRA/EPA Waste Information: If discarded in its purchased form, this material is not a RCRA hazardous waste.
Section 14 – Transport Information USDOT (Domestic Surface):
Not regulated
IMO (Ocean):
IATA/ICAO (Air):
Section 15 – Regulatory Information TSCA (Toxic Substances Control Act): RCRA Status:
All components are on TSCA inventory.
If discarded in its purchased form, this material is not a RCRA hazardous waste.
US Federal Regulatory Information: SARA Title III (Superfund Amendments and Reauthorization Act: 311/312 Hazard Categories: 313 Reportable Components:
Acute, Chronic. None. Page 4 of 5
Section 16 – Other Information Abbreviations and acronyms: USDOT: IMDG: IATA: CAS: LC50: LD50: EC50: RQ:
United States Department of Transportation. International Maritime Code for Dangerous Goods. International Air Transport Association. Chemical Abstracts Service (Division of the American Chemical Society). Lethal concentration, 50 percent. Lethal dose, 50 percent. Median effective concentration. Reportable quantity.
SDS prepared by:
Aquafin product safety department.
DISCLAIMER: We believe the statements, technical information and recommendations contained herein are reliable, but they are given without warranty or guarantee of any kind, expressed or implied, and we assume no responsibility for any loss, damage, or expense, direct or consequential, arising out of their use. Aquafin shall not be responsible for the use of this product in a manner to infringe on any patent or any other intellectual property rights held by others. User is responsible for determining appropriate safety measures and for applying the legislation covering his own activities. We recommend that user makes tests to determine the suitability of a product for its particular purpose prior to use. END OF SDS
Page 5 of 5
(March 21, 2019)