TDS SLQ 040419.pdf
2 Pages
94 KB
Download
<h1>TDS SLQ 040419.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>An AQUAFIN Brand Product</p> <p>Technical Datasheet</p> <p>Pavemend SLQ™</p> <p>Semi-Leveling, Extended VERY RAPID REPAIR MORTAR <br />CSI Div. 03 <br />03 31 23 High Performance Structural Concrete</p> <p>Physical and Technical Data <br />NEAT 2” Cubes</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />SLQ is a cementitious, very rapid setting, self-leveling structural repair <br />mortar suitable for very rapid concrete repair in all climates, especially in <br />near freezing and below freezing applications. It is a single component <br />powder that is water activated, and is suited for aggregate extension. SLQ <br />has 2-4 minutes working time and will reach compressive strengths up to <br />3000 psi within 60 minutes of final set. Designed for horizontal and formed <br />applications.SLQ can be applied in ambient temperature ranges from <br />-20°F to 110°F without special mixing or curing equipment. <br />Typical Applications: <br />Ideal for moderate to cold weather repairs of roads and bridges, airport <br />runways, warehouse or manufacturing facility floors, post tension cable <br />repairs and form and pour projects. Can be used as a temporary repair for <br />asphalt pavement. <br />Surface Preparation: <br />• Concrete surfaces must be structurally sound, free of any loose or <br />deteriorated concrete, dirt, dust, grease, oil, sealers, curing compounds <br />and all other bond-inhibiting materials. <br />• Mechanically prepare surfaces to achieve a surface profile equal to <br />CSP 5-7 as per ICRI Guideline No. 310.2R-13 <br />• Properly clean profiled area by water-blasting. All surfaces must be <br />saturated surface dry (SSD) but with no standing water, immediately <br />prior to application. <br />• Repair areas must have saw cut straight edges with a minimum 3/8” (10 <br />mm) depth as per ICRI Guideline 310.1R – 2008. <br />Mixing: <br />Critical Mix Temperature (CMT): SLQ undergoes an exothermic chemical <br />reaction during blending Heat, the by-product of the reaction, is the <br />indication that the reaction is complete and that the product is ready to <br />be poured. SLQ has a CMT of 85°F/29°C which MUST BE REACHED <br />before placing to ensure performance. Mixing time to reach the CMT <br />will vary with ambient air and mix water temperatures. Contact Aquafin <br />Technical Department with questions regarding CMT and cold or hot <br />weather placements. The use of an infrared thermometer <br />is required for the mixing process to ensure that the CMT <br />85 <br />has been achieved.</p> <p>Compressive <br />Strengths, psi (MPa) <br />ASTM C 109M / <br />ASTM C 39</p> <p>3,000 @ 1 hours <br />> 4,000 @ 3 hours <br />> 4,500 @ 24 hours <br />> 5,000 @ 7 days <br />> 6,000 @ 28 days</p> <p>Flexural Strength, psi <br />(MPa) <br />ASTM C 78</p> <p>> 500 @ 7 days <br />> 600 @ 28 days</p> <p>Splitting Tensile <br />Strength, psi (MPa) <br />ASTM C 496</p> <p>> 150 @ 28 days <br />> 250 @ 28 days</p> <p>Bond Strength, psi <br />(MPa) <br />ASTM C 882</p> <p>> 1,200 @ 24 hours <br />> 1,375 @ 7 days</p> <p>Rapid Freeze Thaw <br />Resistance <br />ASTM C 672</p> <p>99.6% @ 300 cycles <br />(Durability Factor - Retained <br />percentage of Dynamic <br />Modulus)</p> <p>Scaling Resistance, <br />ASTM C 672</p> <p>0 @ 50 cycles <br />lbs/ft2 (kg/m2)</p> <p>Modulus of <br />Elasticity, psi <br />ASTM C 469</p> <p>1.93 EE6 @ 28 days</p> <p>Coefficient of <br />Thermal Expansion,</p> <p>2.95 @ 28 days <br />in/in/°F AASHTO TP 60</p> <p>Length Change, % of <br />total length ASTM <br />C 157</p> <p>< -0.020 @ 28 days soak <br />< -0.030 @ 28 days dry</p> <p>Extended w/ 3/8” <br />Pea Gravel <br />(4” x 8” Cylinders) <br />3,000 @ 1 hours <br />> 4,000 @ 3 hours <br />> 4,500 @ 24 hours <br />> 5,000 @ 7 days <br />> 6,000 @ 28 days</p> <p>Results provided by licensed engineering test laboratory and represent typical results from production <br />materials. Actual results may vary from third party testing results; however, Pavemend materials meet and/or <br />exceed ASTM C928, and exceed established internal quality control standards. All samples were air cured.</p> <p>Additional Physical Properties <br />Set Times at 72°F/22°C <br />Initial set: 2 - 4 minutes <br />Final set: 4 - 10 minutes <br />Yield per Unit</p> <p>Unit Weight (neat): <br />approximately 115 lb/ft3 (1,842 kg/ <br />m3) <br />Neat</p> <p>Extended 50% with 3/8”or <br />1/2”fractured aggregate</p> <p>46 lb. <br />(20.9 kg)</p> <p>0.42 ft3 <br />(0.012 m3)</p> <p>0.60 ft3 <br />(0.017 m3)</p> <p>11 lb <br />(4.99 kg)</p> <p>0.10 ft3 (0.003 m3)</p> <p>0.15 ft3 <br />(0.004 m3)</p> <p>SLQ</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net • www.pavemend.com</p> <p>Page 1of 2 <br />(04/04/19-SM)</p> <p>For <br />& As</p> <p>Pavemend SLQ™ <br />Standard NEAT Procedures (Bucket Mixing with Drill & Paddle) <br />• To ensure product performance, do not divide/separate individual units <br />into smaller portions. Mix entire contents at one time. <br />• Do not hand mix. A drill (6 amp minimum) with a mixer blade turning at <br />least 500 to 800 rpm is required. Drills with speeds greater than 800 <br />rpms may entrain air in the mix. <br />• Ideal water temperature is between 65°F/18°C and 75°F/24°C. <br />If ambient temperatures are above 85°F/29°C, use cold water at <br />approximately 55°F/13°C. <br />1. To begin: Tumble bucket on ground to loosen materials, then dry mix <br />powders in the bucket for approx. 30 seconds with drill and paddle. <br />2. Pour all required water into bucket, on top of SLQ powder. It is very <br />important to rapidly incorporate all of the dry SLQ powders into water <br />to achieve a uniform wet mixture within the first 30 seconds of mixing.: <br />For Each: <br />Add: <br />46 lb (20.9 kg) 5 gallon (18.9 L) <br />11 lb (4.99 kg) 2 gallon (7.6 L) </p> <p>1 U.S. gallon (3.8 L) water <br />1 U.S. quarts (.95 L) water</p> <p>3. Mix material until CMT of 85°F/29°C is reached. Place material into <br />repair area and spread with a trowel, straight edge or squeegee, filling <br />voids and edges. <br />For Aggregate Extension: (Bucket Mixing with Drill & Paddle) <br />• Use only 3/8” (1 cm) or 1/2” (1.3cm) #7 clean washed fractured <br />stone up to 50% maximum by weight. <br />• Add aggregate to mixed material after mixing for 30 seconds. <br />• See mixing instruction for NEAT application above. <br />Application: <br />• Minimum product thickness (neat) is 1/4” (6 mm), and (extended) is 1” <br />(25 mm). There are no restrictions to the depth of product thickness. <br />• For best results, Aquafin recommends monolithic placement of repair <br />materials. Maintain a minimum thickness of 1.0” if repair material must <br />be layered. <br />• Place onto properly prepared concrete substrate and spread with a <br />trowel, come-a-long, or screed to a thickness that matches surrounding <br />concrete. <br />• Upon initial set, finish material to desired finish texture. <br />• Upon final set, the material can be saw-cut, drilled, sanded and/or <br />polished. DO NOT use additional water during the finishing process. <br />• All previously existing joints must be re-established within 1-3 hours of <br />final set. <br />• General loading in 1 hour for wheeled traffic and 20 minutes for <br />foot traffic. For applications 0.5” thick and greater, in ambient and/ <br />or surface temperatures below 50°F/10°C, extend the loading time <br />by 30 minutes for each 10° below 50°F/10°C. For applications <br />1.0” thick and greater, in ambient and/or surface temperatures below <br />40°F/4°C extend the loading time by 30 minutes for each 10° below <br />40°F/4°C. <br />• Self-curing. <br />• Clean all tools and equipment with water prior to the material reaching <br />final set. Cured material must be mechanically removed.</p> <p>Packaging & Shelf Life: <br />• Packaging <br />46 lb (20.9 kg) 5 gallon (18.9 L) bucket GSA P/N: C300 <br />11 lb (4.99 kg) 2 gallon (7.6 L) bucket GSA P/N: C350 <br />• Shelf Life: 3 years (when stored in original unopened bucket) <br />• Storage: Buckets are environmentally sealed and require no special <br />storage requirements. <br />Note: <br />Installer is responsible for proper product application. Site visits by Aquafin <br />personnel or representatives are solely for the purpose of making technical <br />recommendations, not for providing supervision or quality control. <br />Safety: <br />Refer to Safety Data Sheet (SDS). The use of a dust mask, safety <br />goggles and gloves is recommended. This document does not purport to <br />address all of the safety concerns, if any, associated with its use. It is the <br />responsibility of the user of this document to establish appropriate safety <br />and health practices and to determine the applicability of regulatory <br />limitations prior to use. Dispose of water and materials in accordance with <br />Federal, State and Local regulations. Keep out of the reach of children. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one <br />year from the date of installation to be manufactured free of defects and to be <br />consistent with its technical properties as stated in our current Technical Data Sheet. <br />This product must be used as directed and within its stated shelf life. AQUAFIN INC. <br />will replace or at our discretion refund the purchase price of any product, excluding <br />cost of labor, which is proven to be defective. Our product recommendations are <br />based on industry standards and testing procedures. It is the buyer’s obligation <br />to test the suitability of the product for an intended use prior to using it. We <br />assume no warranties written, expressed or implied as to any specific methods of <br />application or use of the product. AQUAFIN INC. MAKES NO WARRANTY AS <br />TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND THIS <br />WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED. <br />AQUAFIN, INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. Any claim for a defectiveproduct <br />must be filed within 30 days of discovery of a problem, and must be submitted with <br />written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Limitations: <br />• Not recommended for surface temperatures above 110°F/43°C <br />or below -20°F/10°C. (Contact Aquafin Technical Department for <br />temperatures below 50°F). <br />• Will not bond to polymers. <br />• Cannot be pumped or mixed in grout mixer or rotating drum concrete <br />mixers due to rapid set times. <br />• Do not add cement or any other admixtures to material.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2of 2 <br />www.aquafin.net • www.pavemend.com <br />(04/04/19-SM)</p>
