TDS TR 120420.pdf
2 Pages
476 KB
Download
<h1>TDS TR 120420.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>An AQUAFIN Brand Product</p> <p>Technical Datasheet</p> <p>Pavemend TR™</p> <p>Extendable, Semi-Leveling, RAPID REPAIR, TROWELABLE MORTAR <br />CSI Div. 03 <br />03 31 23 High Performance Structural Concrete</p> <p>Physical and Technical Data <br />NEAT 2” Cubes</p> <p>Extended w/ 3/8” <br />Pea Gravel <br />(4” x 8” Cylinders)</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, L ow-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />TR is a single component, water activated, rapid setting slope grade <br />(up to 60%) structural repair mortar with a gel like consistency suitable <br />for troweling on horizontal and/or sloped grades and for aggregate <br />extension. TR has 15 to 20 minutes of working time and reaches >2500 <br />psi compressive strengths within 3 hours of final set. TR can be applied in <br />ambient temperature ranges from 40° to 120° Fahrenheit and can be <br />re-tempered repeatedly to a gel state prior to final set without additional <br />water, providing ease of use and reduced material waste.</p> <p>Compressive <br />Strengths, psi (MPa) <br />ASTM C 109 / <br />ASTM C 39</p> <p>> 2,800 @ 3 hours <br />> 5,000 @ 24 hours <br />> 6,000 @ 7 days <br />> 7,000 @ 28 days</p> <p>Flexural Strength, psi <br />(MPa) <br />ASTM C 78</p> <p>> 600 @ 7 days <br />> 1,400 @ 28 days</p> <p>Splitting Tensile <br />Strength, psi (MPa) <br />ASTM C 496</p> <p>> 200 @ 7 days <br />> 400 @ 28 days</p> <p>Bond Strength, psi <br />(MPa) <br />ASTM C 882</p> <p>> 1,200 @ 24 hours <br />> 1,900 @ 7 days</p> <p>Rapid Freeze Thaw <br />Resistance <br />ASTM C 672</p> <p>Typical Applications: <br />Designed specifically for use in horizontal and/or sloped applications, <br />TR is an ideal repair material for roads and bridges, airport runways, <br />warehouse or manufacturing facility floors, loading dock ramps, parking <br />garages, post-tension cable repairs, form and pour projects, overlayment <br />of concrete surfaces, joint repair, pavements etc. Can be used as a <br />temporary repair for asphalt. <br />Surface Preparation: <br />• Concrete surfaces must be structurally sound, free of any loose or <br />deteriorated concrete, dirt, dust, grease, oil, sealers, curing compounds <br />and all other bond-inhibiting materials. <br />• Mechanically prepare surfaces to achieve a surface profile equal to <br />CSP 5-7 as per ICRI Guideline No. 310.2R-13 <br />• Properly clean profiled area by water-blasting. All surfaces must be <br />saturated surface dry (SSD) but with no standing water, immediately <br />prior to application. <br />• Repair areas must have saw cut straight edges with a minimum 3/8” (10 <br />mm) depth as per ICRI Guideline 310.1R – 2008. <br />Mixing: <br />Critical Mix Temperature (CMT): TR undergoes an exothermic chemical <br />reaction during blending Heat, the by-product of the reaction, is the <br />indication that the reaction is complete and that the product is ready to be <br />poured. TR has a CMT of 90˚F/32˚C which MUST BE REACHED before <br />placing to ensure performance. Mixing time to reach the <br />CMT will vary with ambient air and mix water temperatures. <br />Contact Aquafin Technical Department with questions <br />90 <br />regarding CMT and cold or hot weather placements. The <br />use of an infrared thermometer is required for the mixing <br />process to ensure that the CMT has been achieved.</p> <p>> 3,000 @ 3 hours <br />> 3,000 @ 24 hours <br />> 3,000 @ 7 days <br />> 3,000 @ 28 days</p> <p>100% @ 300 cycles</p> <p>(Durability Factor - Retained percentage of Dynamic Modulus)</p> <p>Scaling Resistance, <br />lbs/ft2 (kg/m2) ASTM <br />C 672</p> <p>0 @ 50 cycles</p> <p>Modulus of <br />Elasticity, psi <br />ASTM C 469</p> <p>2.77 @ 28 days</p> <p>Coefficient of <br />Thermal Expansion,</p> <p>2.52 @ 28 days <br />in/in/˚F <br />AASHTO-T336-11</p> <p>Length Change, % of <br />total length ASTM <br />C 157</p> <p>TBD/ -0.020 @ 28 days <br />soak/dry</p> <p>Results provided by licensed engineering test laboratory and represent typical results from production <br />materials. Actual results may vary from third party testing results; however, Pavemend materials meet and/or <br />exceed ASTM C928, and exceed established internal quality control standards. All samples were air cured.</p> <p>Additional Physical Properties <br />Set Times at <br />72°F/22°C <br />Initial set: 10 - 15 minutes <br />Final set: 20 - 25 minutes <br />Yield per <br />Unit</p> <p>Neat</p> <p>Unit Weight (neat): <br />approximately 115 lb/ft3 <br />(1,842 kg/m3) <br />Extended 50% with 3/8”or <br />1/2”fractured aggregate</p> <p>47 lb. <br />(21.3 kg)</p> <p>0.42 ft3 <br />(0.012 m3)</p> <p>0.60 ft3 <br />(0.017 m3)</p> <p>12 lb <br />(5.4 kg)</p> <p>0.12 ft3 <br />(0.003 m3)</p> <p>0.14 ft3 <br />(0.004 m3)</p> <p>TR <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net • www.pavemend.com</p> <p>Page 1of 2 <br />(12/04/20-EK-VB)</p> <p>For <br />& As</p> <p>Pavemend TR™ <br />Standard NEAT Procedures (Bucket Mixing with Drill & Paddle) <br />• To ensure product performance, do not divide/separate individual units <br />into smaller portions. Mix entire contents at one time. <br />• Do not hand mix. A drill (6 amp minimum) with a mixer blade turning at <br />least 500 to 800 rpm is required. Drills with speeds greater than 800 <br />rpms may entrain air in the mix. <br />• Ideal water temperature is between 65°F/18°C and 75°F/24°C. <br />If ambient temperatures are above 85˚F/29˚C, use cold water at <br />approximately 55˚F/13˚C. <br />1. To begin: Tumble bucket on ground to loosen materials, then dry mix <br />powders in the bucket for approx. 30 seconds with drill and paddle. <br />2. Pour all required water into bucket, on top of TR powder. It is very <br />important to rapidly incorporate all of the dry TR powders into water to <br />achieve a uniform wet mixture within the first 30 seconds of mixing.: <br />For Each: <br />Add: <br />47 lb (21.3 kg) unit <br />12 lb (5.4 kg) unit <br /> </p> <p>1 U.S. gallon (3.8 L) water <br />1 U.S. quarts (.95 L) water</p> <p>3. Mix material until CMT of 90˚F/32˚C is reached. Place material into <br />repair area and spread with a trowel, straight edge or squeegee, filling <br />voids and edges. <br />For Aggregate Extension: (Bucket Mixing with Drill & Paddle) <br />• Use only 3/8” (1 cm) or 1/2” (1.3cm) #7 clean washed fractured <br />stone up to 50% maximum by weight. <br />• Add aggregate to mixed material after mixing for 30 seconds. <br />• See mixing instruction for NEAT application above. <br />Application: <br />• Minimum product thickness (neat) is 1/4” (6 mm), and (extended) is 1” <br />(25 mm). There are no restrictions to the depth of product thickness. <br />• For best results, Aquafin recommends monolithic placement of repair <br />materials. Maintain a minimum thickness of 1.0” if repair material must <br />be layered. <br />• Place onto properly prepared concrete substrate and spread with a <br />trowel, come-a-long, or screed to a thickness that matches surrounding <br />concrete. <br />• Upon initial set, finish material to desired finish texture. <br />• Upon final set, the material can be saw-cut, drilled, sanded and/or <br />polished. DO NOT use additional water during the finishing process. <br />• All previously existing joints must be re-established within 1-3 hours of <br />final set. <br />• General loading in 2 to 3.5 hour for wheeled traffic and 60 minutes <br />for foot traffic. For applications 0.5” thick and greater, in ambient and/ <br />or surface temperatures below 50°F/10°C, extend the loading time by <br />30 minutes for each 10° below 50°F/10°C. For applications 1” thick <br />and greater, in ambient and/or surface temperatures below 40°F/4°C <br />extend the loading time by 30 minutes for each 10° below 40°F/4°C. <br />• Self-curing. <br />• Clean all tools and equipment with water prior to the material reaching <br />final set. Cured material must be mechanically removed.</p> <p>Packaging & Shelf Life: <br />• PACKAGING <br />47 lb (21.3 kg) pail GSA P/N: C700 <br />12 lb (5.4 kg) pail GSA P/N: C750 <br />• SHELF LIFE: <br />2 years (when stored in original unopened pail). <br />• STORAGE: <br />Store pails indoors in a cool and dry location. <br />Note: <br />Installer is responsible for proper product application. Site visits by Aquafin <br />personnel or representatives are solely for the purpose of making technical <br />recommendations, not for providing supervision or quality control. <br />Safety: <br />Refer to Safety Data Sheet (SDS). The use of a dust mask, safety goggles <br />and gloves is recommended. This document does not purport to address all <br />of the safety concerns, if any, associated with its use. It is the responsibility of <br />the user of this document to establish appropriate safety and health practices <br />and to determine the applicability of regulatory limitations prior to use. Keep <br />out of the reach of children. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed or implied as to any specific methods of application or use of the product. <br />AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defectiveproduct must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Limitations: <br />• Not recommended for surface temperatures above 110˚F/43˚C or <br />below 40°F/4°C. <br />• Will not bond to polymers. <br />• Cannot be pumped or mixed in grout mixer or rotating drum concrete <br />mixers due to rapid set times.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net • www.pavemend.com</p> <p>Page 2 of 2 <br />(12/04/20-EK-VB)</p>
