TDS-InjectProECO-LV110119.pdf
2 Pages
454 KB
Download
<h1>TDS-InjectProECO-LV110119.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectProECO-LV</p> <p>Hydrophobic, flexible polyurethane grout for stopping active leaks in cracks <br />No harmful phthalates <br />CSI Div. 03 <br />03 64 00 Injection Grouting</p> <p>ECO <br />FRIENDLY <br />TECHNOLOGY</p> <p>Product Description: <br />InjectProECO-LV is a closed cell, high performance polyurethane injection <br />grout designed for use to cut off gushing water leaks with a high flow <br />rate and/or high hydrostatic pressure in low range dynamic cracks. <br />When it comes in contact with water, the grout expands up to 800% <br />and quickly cures to a tough, flexible, closed-cell polyurethane foam that <br />is generally unaffected by common corrosive environments and is not <br />subject to shrinkage due to wet/dry cycles. InjectProECO grouts are all <br />environmentally friendly and formulated without harmful phthalates or <br />VOC’s. <br />The system is comprised of an “A” component (base resin) and a “B” <br />component (accelerator). The “B” component is used by the applicator to <br />adjust the set times for various job site specific conditions. <br />Typical Applications: <br />Any concrete structure with water leaks such as: <br />• Water Retaining Structures, Concrete Dams, Tunnels, Elevator Pits, <br />Parking Garages, etc. <br />Advantages: <br />• Zero VOC’s - meets LEED criteria <br />• 100% solids, non-flammable, non-toxic permanent seal <br />• Hydrophobic - can be used in wet and dry environments <br />• Accelerator and resin stable to -40°F. <br />• Pumped as a single component <br />• Excellent elongation creates a tight seal in moving cracks <br />• Adjustable reaction times <br />• Non-hazardous shipping <br />Reaction Times & Use of Accelerator: <br />The reaction time can be adjusted by the addition of accelerator “B” <br />into the base resin prior to pumping. The resulting profile is affected by <br />temperature and the amount of moisture present. <br />Typical reaction times: <br />Accelerator % Reaction <br />Polymerisation <br />6% <br />30 seconds <br />115 seconds <br />8% <br />25 seconds <br />90 seconds <br />10% <br />20 seconds <br />75 seconds <br />Installation Procedures: <br />Refer to the Aquafin InjectPro Grouting Guideline for full instructions. Mix <br />both the resin (Component A) and accelerator (Component B) before <br />combining. <br />• Pour the desired amount of InjectProECO-LV Resin Component A into a <br />clean pail. <br />• Measure the appropriate amount of InjectProECO-LV Accelerator <br />Component B and pour into the InjectProECO-LV Resin, stirring until <br />Check our website for the latest version of the Technical Data Sheet. <br />www.aquafin.net</p> <p>Physical Properties - liquid <br />(un-cured)</p> <p>InjectProECO-LV <br />Resin</p> <p>ECO-LV <br />Accelerator</p> <p>Amber</p> <p>Clear</p> <p>100%</p> <p>n/a</p> <p>Color <br />Solids (ASTM D2369)</p> <p>Viscosity (ASTM D1638)</p> <p>~245 cps</p> <p>~8 cps</p> <p>Density (ASTM D4659)</p> <p>~67 lbs. ft3 <br />(~1.0 g/cm3)</p> <p>~57 lbs. ft3 <br />(~0.7 g/cm3)</p> <p>Flash Point (ASTM D92)</p> <p>>300°F</p> <p>>300°F</p> <p>Physical Properties - solid (cured) InjectProECO-LV <br />Density - Free Foam (ASTM D1622)</p> <p>~2.4 lbs/ft3</p> <p>Density - Confined (ASTM D1622)</p> <p>~96 lbs/ft3</p> <p>Compressive Strength (contingent on confinement) <br />Toxicity</p> <p>26 psi <br />non-toxic</p> <p>adequately mixed. Never use more accelerator than recommended. <br />Excess accelerator will cause significant expansion that is prone to <br />shrinkage. <br />During injection, the grout will follow the path of least resistance. When <br />the material has stopped penetrating it will continue to expand against the <br />confines of the crack/joint and compress within itself, forming a very dense, <br />closed cell material stopping the leak. <br />Packaging: <br />InjectProECO-LV Resin: <br />5 gallon pails <br />InjectProECO-LV Accelerator: 32 oz. container <br />(5% dosage per 5 gallons of resin. For 10% acceleration use 2 x 32 oz.)</p> <p>Storage & Shelf Life: <br />Shelf life is two years when stored properly. Product is highly moisture <br />sensitive. Store in original sealed containers at temperature between 40°F <br />– 90°F. Opened containers must be handled properly to prevent moisture <br />contamination. <br />Limitations: <br />• Temperature significantly affects viscosity. Protect material from excessive <br />heating and cooling prior to grouting to avoid affecting viscosity. <br />• If using water baths to cool or heat pails avoid splashes to prevent water <br />coming in direct contact with resin - this will activate the reaction. Do not <br />warm material or packaging above 90°F. <br />• Do not reseal containers of contaminated materials as it can create pressure. <br />• Clean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material <br />such as clay or vermiculite and transfer to metal waste containers. <br />Wash area with decontamination solution (5-10% solution of sodium <br />carbonate). Dispose of waste in accordance with federal, state and <br />local regulations. <br />Page 1 of 2</p> <p>(11/01/19-JW, EK)</p> <p>InjectProECO-LV <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed or implied as to any specific methods of application or use of the product. <br />AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(11/01/19-JW,EK)</p>
