072600 + 099656 Moisture vapor control VAPORTIGHT COAT-SG3 1210.pdf
4 Pages
211 KB
Download
<h1>072600 + 099656 Moisture vapor control VAPORTIGHT COAT-SG3 1210.pdf</h1> <p>GUIDE SPECIFICATION</p> <p>VAPORTIGHT COAT®-SG3 <br />Copyright 2001, AQUAFIN, Inc., 505 Blue Ball Rd., #160, Elkton, MD 21921 <br />(410) 392-2300 (800-394-1410) <br />************************************************************************************** <br />SECTION 072600 <br />SURFACE APPLIED VAPOR REDUCTION SYSTEMS <br />or <br />SECTION 099656 <br />EPOXY MOISTURE MITIGATION SYSTEMS <br />PART 1 - GENERAL <br />1.1</p> <p>SECTION INCLUDES <br />A.</p> <p>Furnish all labor, materials, tools and equipment as necessary to perform installation of a <br />surface applied moisture mitigation system (vapor retarder) on new and/or existing concrete <br />slabs free of oil contamination or previously treated with a sealer, as shown on drawings and <br />as specified in this section.</p> <p>B.</p> <p>Repairs and preparation of concrete floors.</p> <p>C.</p> <p>Related Sections: (Specifier: Delete or add necessary Sections) <br />1. <br />2. <br />3. <br />4. <br />5. <br />6. <br />7. <br />8.</p> <p>1.2</p> <p>1.3</p> <p>See section 033000 Cast-in-Place Concrete. <br />See section 096200 Specialty Flooring. <br />See section 096300 Masonry Flooring. <br />See section 096400 Wood Flooring. <br />See section 096500 Resilient Flooring. <br />See section 096600 Terrazzo Flooring. <br />See section 096700 Fluid-Applied Flooring. <br />See section 096800 Carpet.</p> <p>REFERENCES <br />A.</p> <p>ASTM F 1869 - Standard Test Method for Measuring Moisture Vapor Emission Rate of <br />Concrete Subfloor Using Anhydrous Calcium Chloride; 1998.</p> <p>B.</p> <p>ASTM F 2170 - Standard Test Method for Determining Relative Humidity in Concrete Floor <br />Slabs Using in situ Probes; 2009.</p> <p>C.</p> <p>ASTM E 1907 - Standard Practices for Determining Moisture-Related Acceptability of <br />Concrete Floors to Receive Moisture-Sensitive Finishes; 1997.</p> <p>D.</p> <p>ASTM E 96 - Standard Test Methods for Water Vapor Transmission of Materials; 1995.</p> <p>E.</p> <p>ASTM D 4541 B - Pull-Off Strength of Coatings; 1995, Modified.</p> <p>F.</p> <p>ASTM E 648-03 - Standard Test Method for Critical Radiant Flux of Floor-Covering Systems <br />using a Radiant Heat Energy Source.</p> <p>SUBMITTALS</p> <p>072600-1 or 099656-1</p> <p>1.4</p> <p>1.5</p> <p>1.6</p> <p>1.7</p> <p>A.</p> <p>General: <br />Submit manufacturer's certification that proposed materials, details and systems as indicated <br />and specified fully comply with manufacturer's details and specifications. If any portion of <br />Contract Documents do not conform to manufacturer's standard recommendations, submit <br />notification of portions of design that are at variance with manufacturer's specifications.</p> <p>B.</p> <p>Product Data: <br />1. <br />Submit manufacturer's literature, installation instructions and MSDS (Material Safety <br />Data Sheet) for each product. <br />2. <br />Test data: <br />Submit independent testing laboratory data for product, evidencing: <br />a. <br />up to 97% reduction of water vapor transmission (tested as per <br />ASTM E 96-95). <br />b. <br />product is insensitive to alkaline environment up to pH 14 (tested <br />as per ASTM D 1308) <br />c. <br />no after flaming, no delamination, warpage or flaming pieces when <br />subjected to radiant heat as per ASTM E 648-03.</p> <p>QUALITY ASSURANCE <br />A.</p> <p>Manufacturer Qualifications: <br />1. <br />Company specializing in manufacturing products specified in this Section with <br />minimum 10 years documented experience.</p> <p>B.</p> <p>Installer Qualifications: <br />1. <br />Acceptable to manufacturer with documented experience on at least 3 projects of <br />similar nature in past 5 years and/or training provided by the product manufacturer.</p> <p>DELIVERY, STORAGE AND HANDLING <br />A.</p> <p>Deliver and store in a dry, well ventilated area at minimum 50 deg F (10 deg C) and <br />maximum 90 deg F (32 deg C).</p> <p>B.</p> <p>Deliver materials in manufacturer's unopened containers fully identified with brand, type, <br />grade, class and all other qualifying information. Provide Material Safety Data Sheets for <br />each product.</p> <p>SYSTEM REQUIREMENTS <br />A.</p> <p>Coordinate floor sealing installation with other trades.</p> <p>B.</p> <p>Provide materials and accessories in timely manner so as not to delay Work.</p> <p>PROJECT CONDITIONS <br />A.</p> <p>Maintain surfaces to be sealed and surrounding air temperature at not less than 50 deg F (10 <br />deg C).</p> <p>B.</p> <p>Exercise caution when temperatures exceed 90 deg F (32 deg C).</p> <p>PART 2 - PRODUCTS <br />2.1</p> <p>MANUFACTURERS <br />A.</p> <p>Approved Manufacturers: AQUAFIN, Inc. 505 Blue Ball Rd., #160, Elkton, MD, Phone (800) <br />394-1410 or (410) 392-2300; Fax (410) 392-2324; e-mail info@aquafin.net.</p> <p>072600-2 or 099656-2</p> <p>B.</p> <p>2.2</p> <p>Requests for substitutions will be considered only if submitted to the architect/engineer in <br />writing and must include substantiation of product performance, 10 days prior to the original <br />bid date.</p> <p>MATERIALS <br />A.</p> <p>Moisture Vapor Emission Reduction Control System (concrete floor sealer): One-part system <br />consisting of a two-component, 100% solids, solvent free, moisture tolerant, high density, low <br />odor, chemically enhanced epoxy based product which must reduce vapor emissions <br />(MVER) to 3 lbs/24 hrs*1000 SF or less and be compatible with floor finishes and adhesives <br />approved by the manufacturer. Characteristics: <br />® <br />1. Product: <br />VAPORTIGHT COAT -SG3 <br />2. Component-A and B: <br />Precise blend of clear and yellowish liquid <br />3. VOC content: <br />0 g/L <br />4. Bond/Adhesion: (ASTM D-4541) <br />>220 psi <br />(>1.5 Mpa) at 28 day old concrete <br />-08 <br />2 <br />5. Permeance: (ASTM E-96) <br /><0.5 perm (<3.1E grams/Pa*s*m ) <br />6. Alkaline Resistance: (ASTM D-1308) up to pH 14 <br />7. Vapor Reduction: (ASTM E-96) <br />up to 97% <br />8. Cured for installation of flooring: <br />12 hrs at 73 deg F (23 deg C) <br />9. pH on cured surface: <br />7 <br />2 <br />10. Average Critical Radiant Flux: <br />1.00 W/cm (ASTM E 648-03)</p> <p>PART 3 - EXECUTION <br />3.1</p> <p>3.2</p> <p>EXAMINATION <br />A.</p> <p>Examine all construction substrates and conditions under which concrete floor sealer <br />material is to be installed. Do not proceed with the concrete floor sealer installation until <br />unsatisfactory conditions are corrected.</p> <p>B.</p> <p>Assure that surfaces to be treated do not contain any kind of sealer or organic compounds.</p> <p>C.</p> <p>Anhydrous Calcium Chloride Testing as per ASTM F-1869 and/or Relative Humidity Testing <br />as per ASTM F-2170: <br />1. Before installation of concrete floor sealer: use tests carried out by Architect/Engineer <br />during study phase, and confirm by testing through installer or independent laboratory <br />prior to installation of concrete floor sealer. <br />2. After installation of concrete floor sealer: not required by manufacturer of specified <br />concrete floor sealer, unless to be carried out on a test application, specified during bid <br />stage. <br />3. Alternatively or in addition to Calcium Chloride Testing use Relative Humidity tests <br />carried out by Architect/Engineer during study phase, and confirm by testing through <br />installer or independent laboratory prior to installation of concrete floor sealer.</p> <p>PREPARATION <br />A.</p> <p>Protect adjacent surfaces not designated to receive concrete floor sealer.</p> <p>B.</p> <p>Substrate preparation: <br />1. Remove existing floor coverings, coatings and adhesives down to bare concrete, curing <br />compounds, efflorescence, dust, grease, laitance, etc. with steel shot blasting, abrasive</p> <p>072600-3 or 099656-3</p> <p>(sand) blasting or grinding using a diamond cup blade (run in low gear to prevent <br />polishing effect). Acid etching is not allowed. <br />2. Assure that all slabs have surface profile ICRI CSP 3 - 5 (ICRI, Des Plaines, IL, <br />Guideline No.03732.) for mechanical bond (i.e. medium grit sandpaper). Smooth <br />surfaces are not acceptable, they must be shot blasted. <br />3. Burn off reinforcing fibers and collect and vacuum remains. <br />4. Repair defective areas such as honeycombs, cracks or other defects with a suitable <br />repairing or manufacturer recommended mortar. <br />5. Treat saw cut and expansion joints as per manufacturer’s application guideline. <br />6. Install cementitious underlayment, leveling mortars, flash patching, on top of surface <br />applied concrete floor sealer. <br />7. Do not apply floor sealer to unprotected surfaces or surfaces where water has <br />accumulated (puddles). <br />3.3</p> <p>INSTALLATION <br />A. Mix concrete floor sealer material in proportions recommended by manufacturer. <br />B. Apply concrete floor sealer material in quantities as per manufacturer's specifications and <br />recommendations. <br />1. Apply in one coat at specified rate. <br />2. Apply using non-shed synthetic roller or notched squeegee to the still moist substrate, and <br />carefully scrub it into the pores with a long handled scrub brush. Follow with a non-shed <br />synthetic roller to achieve a uniform coverage. <br />C. Where specified install leveling <br />recommendations.</p> <p>course</p> <p>as</p> <p>per</p> <p>manufacturer’s</p> <p>specifications</p> <p>and</p> <p>D. Where specified install floor covering as per manufacturer’s specifications and recommendations. <br />G. Note: <br />1. Water based adhesives under VCT, sheet vinyl, linoleum, rubber backed carpet or <br />other non-breathable flooring systems require a cementitious underlayment on top of the <br />concrete floor sealer for their curing process. Consult adhesive manufacturer for <br />recommended minimum thickness of cementitious underlayment. <br />2. Pressure sensitive adhesives installed directly over concrete floor sealer require a longer <br />"tack" time than listed on manufacturer's literature to prevent adhesive moisture entrapment. <br />3.4</p> <p>ACCEPTANCE <br />A.</p> <p>Remove left over materials and any foreign material resulting from the work from the site.</p> <p>B.</p> <p>Clean adjacent surfaces and materials. <br />END OF SECTION</p> <p>072600-4 or 099656-4</p> <p>Project: ........ (12/10)</p>
