3 Aquafin 1K 062926.pdf
4 Pages
170 KB
Download
<h1>3 Aquafin 1K 062926.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />e: info@aquafin.net <br />e: technical@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>AQUAFIN®-1K</p> <p>Cementitious Waterproofing & Protective Coating <br />CSI Div. 07, 09, 13, 32, + 33 <br />07 11 16 Cementitious Dampproofing <br />07 14 16 Cold Fluid-Applied Waterproofing <br />07 16 00 Cementitious and Reactive Waterproofing <br />07 16 13 Polymer Modified Cement Waterproofing <br />09 97 23 Concrete and Masonry Coatings <br />09 97 23.24 Concrete Water Storage Tank Painting <br />09 97 26 Cementitious Coatings <br />09 97 26.13 Interior Cementitious Coatings <br />09 97 26.23 Exterior Cementitious Coatings <br />13 01 13 Operation and Maintenance of Aquariums <br />32 32 13 Cast-in-Place Concrete Retaining Walls <br />32 32 19 Unit Masonry Retaining Walls <br />33 01 10 Operation and Maintenance of Water Utilities <br />33 16 00 Water Utility Storage Tanks <br />33 16 36 Ground-Level Reinforced Concrete Water Storage Tanks <br />33 16 61 Underground Concrete Water Storage Cisterns <br />33 36 00 Wastewater Utility Storage Tanks <br />33 36 36 Ground-Level Reinforced Concrete Wastewater Storage Tanks <br />33 36 43 Underground Reinforced Concrete Wastewater Storage Tanks <br />33 49 23 Storm Drainage Water Retention Structures</p> <p>Physical and Technical Data</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials:……....... ..................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials, Paints and Coatings:.....1 Point. <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above. <br />EPD (Environmental Product Declaration) available by request.</p> <p>Product Description: <br />AQUAFIN®-1K is a cement-based, polymer modified, waterproof coating. <br />Mixed with water, it forms a dense, rigid surface barrier. It consists of <br />Portland cement, well graded quartz sand and polymer enhanced <br />chemical ingredients. <br />Typical Applications: <br />AQUAFIN®-1K is commonly used for a wide variety of positive and <br />negative side waterproofing on interior and exterior concrete and masonry <br />substrates, including above, on, and below grade projects such as: <br />• Basement walls and foundation walls <br />• Elevator pits <br />• Parking garage walls <br />• Retaining walls <br />• Water tanks: drinking, storm, reclaimed, and open wastewater <br />• Zoo ponds and aquarium tanks <br />• As the required base coat for a variety of waterproofing applications <br />prior to receiving AQUAFIN®-2K/M top coat <br />Advantages: <br />• One-component, just mix with water <br />• Stand-alone coating or use in combination with AQUAFIN®-2K/M <br />• Polymer modified <br />Check our website for the latest version of the Technical Data Sheet. <br />www.aquafin.net</p> <p>Aggregate State:</p> <p>Powder</p> <p>Color:</p> <p>Gray or White</p> <p>Bulk Density:</p> <p>88 lb/ft3 (1.4 kg/L) dry; <br />116 lb/ft3 (1.85 kg/L) wet</p> <p>VOC:</p> <p>0% (0 g/L)</p> <p>Pot Life:</p> <p>Approx. 60 minutes</p> <p>Drying Time:</p> <p>~2 to 4 hours at 68°F (20°C)</p> <p>Compressive Strength (ASTM C109):</p> <p>4,000 psi (27.6 MPa) @ 28 <br />days. Gray and White</p> <p>Flexural Strength <br />EN 196/1 (ASTM C348 modified):</p> <p>300 psi (2.07 MPa) @ 28 <br />days. Gray and White</p> <p>Shrinkage (ASTM C596):</p> <p>28 days: -0.014%</p> <p>Vapor Permeability <br />Permeance - (ASTM E96):</p> <p>Permeance: 8 perms <br />(untreated control: 10 perms)</p> <p>Potable water certified NSF/ANSI/ <br />CAN Standard 61 by WQA:</p> <p>For a copy of approval go to <br />www.wqa.org</p> <p>Microbiological growth <br />DVGW-W270 Germany:</p> <p>not supported</p> <p>Permeability +/- side water head. <br />DIN 1048 sample 80 mils (2.0 mm) <br />thick:</p> <p>No water ingress with: 50 ft <br />(15 m) (1.5 bar) hydrostatic <br />pressure.</p> <p>All data are average values obtained under laboratory conditions. In practical <br />use temperature, humidity, and absorbency of the substrate may influence the <br />above given values</p> <p>• Potable water certified as per NSF/ANSI/CAN Standard 61 <br />• Resists strong hydrostatic pressure <br />• Not a vapor barrier - lets concrete “breathe” <br />• Excellent freeze/thaw resistance <br />• Can be applied to moist concrete/substrate <br />• UV stable <br />• Non flammable - no odor - non toxic <br />Please refer to Technical Bulletin “Recoating and Repairs <br />with 1K and 2K/M” for additional information. <br />Plug Active Water Leaks: <br />• If water is accumulating from an active leak(s) through cracks or <br />joints in in masonry walls, concrete walls, or concrete floors, Aquafin <br />recommends the process of injection grouting as a first step in stopping <br />severe water intrusion. For more information about Aquafin’s extensive <br />line of Injection Grouts, contact your local Aquafin Representative. <br />• Leaking cracks and other minor leaks (with little to no water <br />accumulation) can be plugged using MORTAR-LN, FIX 10-S, or <br />MORTAR-PLUG-IC. Contact Aquafin Technical Services for guidance. <br />Refer to the current MORTAR-LN, FIX 10-S, or MORTAR-PLUG-IC <br />Page 1 of 4 <br />(06/29/26-EK,AC)</p> <p>AQUAFIN®-1K <br />Technical Data Sheet (TDS) for substrate preparation instructions and <br />other important information. <br />Substrate Preparation: <br />• All substrates must be strong, solid, stable and of load bearing capacity. <br />• Areas designated to receive repairs must remain structurally sound <br />and stable during demolition and surface preparation work, and these <br />conditions must continue throughout the course of the repair work. Any <br />areas of concern or uncertainty should be discussed immediately with <br />the site Superintendent and brought to the attention of the EOR (Engineer <br />of Record). <br />• Substrates must be clean and free from all potential bond breakers such <br />as sand, dirt, dust, efflorescence and mineral deposits, cement laitance, <br />grease, oil, previous coatings, paint, sealers, water repellants, curing <br />compounds, etc. Mechanically clean the substrate to remove any bondinhibiting substances and/or contaminants. <br />• New concrete must be at least 5 days old, or concrete must have <br />reached a minimum 2,500 psi (17.2 MPa) compressive strength. <br />• Repair any loose masonry units on CMU block, brick, and rubble stone <br />masonry walls. <br />• All concrete and masonry surfaces should be even and flush, and free <br />from voids, bug holes, gaping cracks, honey combs, or ridges. <br />•M <br /> echanically remove all laitance, loose or deteriorated concrete by <br />suitable means. <br />• Mechanically prepare all surfaces (including new concrete) to achieve <br />a surface profile equal to CSP 3-5 as per ICRI Guideline No. 310.2R13. Wet or dry sand-blasting, vertical shot blasting, and hydro blasting <br />(high pressure water-blasting at > 5,000 psi) are the preferred methods. <br />• Properly clean mechanically profiled area(s) by hydro blasting (waterblasting) or thorough pressure washing. <br />• Pre-water (thoroughly soak) the substrate extremely well with clean <br />water. Pay particular attention to substrates with excessive absorption <br />such as CMU block walls and any applications during hot/windy <br />conditions. <br />• All surfaces must be saturated surface dry (SSD), which is damp but with <br />no standing water, immediately prior to the application of AQUAFIN®1K. <br />• The surface of MORTAR-V/O CI, MORTAR- QuickPatch, and MORTARScreed CI also require mechanical preparation. <br />• Repairs and parge coats using MORTAR-LN do not require additional <br />mechanical preparation. Apply AQUAFIN®-1K over MORTAR-LN while <br />it is still “green”. <br />• Mechanical preparation is not typically required over repairs with <br />MORTAR-40 CI if finished with a rough texture. <br />In addition to general surface preparation requirements listed above, the <br />following supplementary guidance is also provided: <br />•C <br /> oncrete Floors (such as elevator pit floors): <br />• (Interior floors): Use MORTAR-LN, MORTAR-QuickPatch, <br />MORTAR-40 CI or MORTAR-Screed CI to repair interior concrete <br />floors. <br />•C <br /> oncrete Tank Bottoms: <br />•U <br /> se MORTAR-LN or MORTAR-40 CI to repair concrete tank <br />bottoms. <br />•C <br /> oncrete Wall Structural Repairs: <br />•U <br /> se MORTAR-40 CI for structural repairs on interior and exterior <br />concrete walls. <br />•C <br /> oncrete Wall Non-Structural Repairs: <br />• (Interior walls): Use MORTAR-LN or MORTAR-V/O CI to fill in <br />surface voids (bug holes), and perform non-structural repairs. <br />• (Exterior walls): Use MORTAR-V/O CI to fill in surface voids (bug <br />holes), and perform non-structural repairs.</p> <p>•C <br /> MU Block Walls: <br />• (Interior walls): Use MORTAR-LN or MORTAR-V/O CI to fill in <br />any missing mortar in the mortar joints and create a flush, even <br />surface. <br />• (Exterior walls): Use MORTAR-V/O CI to fill in any missing mortar <br />in the mortar joints and create a flush, even surface. <br />•B <br /> rick or Rubble Stone Walls: <br />• (Interior walls): Use MORTAR-LN or MORTAR-V/O CI as parge <br />coat to create a flush, even surface. <br />• (Exterior walls): Use MORTAR-V/O CI as a parge coat to create <br />a flush, even surface. <br />Note: Multiple parge coats may be required for old rubble <br />stone walls. <br />•D <br /> rilled Injection Grouting Holes and Tie Holes: <br />• (Interior walls): Prepare holes and fill flush to surface with <br />MORTAR-LN or MORTAR-V/O CI. <br />• (Exterior walls): Prepare holes and fill flush to surface with <br />MORTAR-V/O CI. <br />•S <br /> tatic Cracks Exceeding 0.02” (0.4 mm): <br />• (Interior cracks, minor leaks): Prepare interior cracks with minor <br />leaks and fill flush to surface with MORTAR-LN, FIX 10-S, or <br />MORTAR-PLUG-IC. <br />• (Interior cracks, non-leaking): Prepare non-leaking interior cracks <br />and fill flush to surface with MORTAR-LN or MORTAR-V/O CI. <br />• (Exterior cracks, non-leaking): Prepare non-leaking exterior cracks <br />and fill flush to surface with MORTAR-V/O CI. <br />•R <br /> eglets in Perimeter Joints (Wall-to-Floor Joints) or Corner Joints (Wallto-Wall Joints): <br />•C <br /> reate reglet, prepare cavity, and fill flush to surface with <br />MORTAR-LN. <br />•C <br /> ant/Cove in Perimeter Joints (Floor-to-Wall Joints), Corner Joints <br />(Wall-to-Wall Joints) or Wall-to-Ceiling Joints: <br />•U <br /> se MORTAR-LN to form a triangular cant/cove over perimeter <br />joints where the concrete floor meets the concrete or masonry wall, <br />and/or over corners where concrete and/or masonry walls meet, <br />and/or over the joint where the concrete or masonry wall meets <br />the concrete ceiling. <br />Notes: Refer to the current FIX 10-S, MORTAR-40 CI, MORTAR-LN, <br />or MORTAR-PLUG-IC, MORTAR-QuickPatch, MORTAR-Screed CI or <br />MORTAR-V/O CI TDS for preparation instructions and other important <br />information. <br />Jobsite Conditions & Preparation <br />• Protect areas not to be treated from AQUAFIN®-1K. Hardened <br />AQUAFIN®-1K can only be removed mechanically. <br />• Protect and seal alkali sensitive metal substrates such as copper, <br />aluminum, galvanized or zinc treated metal first with a primer (i.e. <br />KRYLON Primer, or equal) prior to applying (overcoating) with <br />AQUAFIN®-1K. <br />• Protect mixing and application areas from direct sunlight and wind. <br />Provide artificial shade and wind breaks when needed. <br />• Only proceed with application when ambient and surface temperatures <br />are above 40°F (4°C) and rising and below 90°F (32°C). <br />• Do not apply AQUAFIN®-1K when temperatures are expected to fall <br />below 40°F (4°C) within 24 hours after placement. <br />• Do not apply AQUAFIN®-1K to frozen or frost covered concrete or <br />masonry surfaces. <br />• Do not apply AQUAFIN®-1K when rain is expected within 4 hours after <br />placement over vertical surfaces, or within 8 hours after placement over <br />horizontal surfaces.</p> <p>Check our website for the latest version of the Technical Data Sheet. Only the current version is legally binding and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 4 <br />www.aquafin.net <br />(06/29/26-EK,AC)</p> <p>AQUAFIN®-1K <br />Mixing: <br />• Add the AQUAFIN®-1K powder to water and mix for at least 3 minutes. <br />• Use the following powder-to-water mix ratios (by volume): <br />•B <br /> rush or Broom Application: <br />•5 <br /> parts powder to 2 parts clean water <br />• (Or) 50 lb powder to 1.6 - 1.7 gal water (22.7 kg to 6.0 - 6.4 L) <br />•M <br /> ix to a creamy slurry consistency <br />• Spray Application: <br />•5 <br /> 0 lb powder to up to 2.0 gal clean water (7.6 L) <br />•M <br /> ix to a pumpable consistency <br />Application: <br />Read all instructions thoroughly prior to installation. <br />• Always apply AQUAFIN®-1K over a damp, laitance-free, properly <br />prepared SSD substrate. <br />• AQUAFIN®-1K may be applied using a Tampico fibered brush, <br />a masonry brush, a broom or appropriate compressed-air spray <br />equipment such as a hopper gun, peristaltic pump (i.e. Quikspray <br />carrousel pump) or rotor stator pump (i.e. Hy-Flex “Spray Buddy”). Do <br />not use a roller to apply AQUAFIN®-1K. <br />Tampico Fibered Brush, Masonry Brush or Broom: <br />1. Work the first coat of AQUAFIN®-1K into the surface to ensure <br />good contact and bonding with the surface of the concrete, <br />masonry, or cement-based parge coat. <br />2. Brush-apply AQUAFIN®-1K in an East-West (left to right) direction. <br />3. Brush-apply second coat in a North-South (up and down) <br />direction. <br />Hopper Gun, Peristaltic Pump, or Rotor Stator Pump: <br />1. Apply AQUAFIN®-1K evenly ensuring a consistent thickness of <br />application. Follow the written instructions of the gun or pump <br />manufacturer. <br />2. Apply the second coat as soon as the first coat has set, but is still <br />”green“. [Normally 4 - 6 hours at 68°F (20°C), 60% RH]. Apply the <br />second coat within 24 hours. Refer to chart at the bottom of page 4 <br />on this TDS for mil thickness and number of coats. <br />Note: If the application window is missed for the second coat of <br />AQUAFIN®-1K, refer to Technical Bulletin “Recoating and Repairs with 1K <br />and 2K/M” for information. <br />Finish: <br />• After application, AQUAFIN®-1K can be left as a brushed finish, or it <br />can be smoothed flat using a rounded-edge steel trowel. <br />Decoration & Tiling: <br />AQUAFIN-1K must be completely clean and dry prior to painting, coating <br />or tiling. Clean the dry surface of AQUAFIN®-1K using a stiff, dry brush. <br />• P aint: Allow AQUAFIN®-1K to dry for at least 3 days prior to <br />painting with a breathable, water-based, acrylic paint. <br />• Tile: Allow AQUAFIN®-1K to dry for at least 3 days prior to tile <br />installation using a cement-based tile mortar. <br />• T op Coating with AQUAFIN-2K/M: Allow AQUAFIN®-1K to dry <br />for at least 24 hours. Apply AQUAFIN®-2K/M as a top coat over <br />AQUAFIN®-1K within 72 hours. <br />Note: If the application window is missed for the AQUAFIN®2K/M, refer to Technical Bulletin “Recoating and Repairs with 1K <br />and 2K/M”. <br />Protection: <br />• Protect from rain for 4 hours for vertical surfaces, and 8 hours for <br />horizontal surfaces. <br />• Protect from foot traffic for a minimum 24 hours. <br />• Do not expose to hydrostatic pressure for approx. 7 days. <br />• Do not back fill for 3 days. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Curing: <br />• Application in Hot and/or Dry Environments: <br />•D <br /> amp cure AQUAFIN®-1K for at least 3 days in hot and/or dry <br />environments. <br />• Application in Humid or Poorly Ventilated Areas (tanks, pits, etc): <br />• Provide air circulation for 24 hours following the AQUAFIN®-1K <br />treatment in poorly ventilated areas. <br />• Use de-humidifiers in indoor areas where condensation exists or <br />appears until AQUAFIN®-1K has properly set. <br />• Potable Water Applications: <br />• Damp cure AQUAFIN®-1K for at least 7 days for use in contact <br />with potable water. <br />Notes: AQUAFIN®-1K requires good air circulation for proper curing. <br />Stagnant air will extend the curing time and drying time and increase the <br />chance of discoloration. Do not cover AQUAFIN®-1K with plastic sheeting <br />or use any type of non-breathable covering as a damp-curing method. <br />Cooler temperatures will extend the curing time and drying time. During <br />winter time, do not use un-controlled direct air blowing gas or oil heaters to <br />keep air warm. <br />Clean-up: <br />Clean tools and equipment with water immediately after use. Cured <br />material must be mechanically removed. <br />Limitations: <br />• Curing times and drying times are approximate and will vary depending <br />on ambient (air) temperature, mix water temperature, the temperature <br />of AQUAFIN®-1K dry powder in the packaging, surface temperature <br />of host concrete or host masonry, host concrete or host masonry profile, <br />and the application thickness. <br />• Do not thin AQUAFIN®-1K with additional water or any solvents. <br />• Do not use AQUAFIN®-1K as a parge coat. <br />• Do not exceed total two-coat thickness of 100 mils (2.5 mm) when <br />applying AQUAFIN®-1K. <br />• Do not use AQUAFIN®-1K in swimming pools, waterfalls for swimming <br />pools, hot tubs, or fountains. <br />• Do not use AQUAFIN®-1K in areas exposed to “soft” water. <br />• AQUAFIN®-1K is not recommended for application over hollow <br />terracotta masonry (old structural clay tile). <br />• AQUAFIN®-1K is not designed for use with AQUAFIN® CRACK <br />SEALING TAPE, AQUAFIN® JOINT SEALING TAPE-2000, AQUAFIN® <br />JOINT SEALING TAPE-2000-S or SEALING GASKET-18/18. <br />• Do not re-temper or use additional water during the finishing process. <br />The addition of excess water will negatively affect the material’s final <br />properties and appearance. <br />• Do <br />Do not apply AQUAFIN®-1K <br />1K to a dry substrate. <br />• Do not apply non-breathable, non-vapor permeable, paints or coatings <br />(such as epoxy coatings) over AQUAFIN®-1K. <br />• Do not apply solvent-based paints or coatings over AQUAFIN®-1K. <br />• Like all cementitious waterproofing products, variations in temperature, <br />humidity, substrate moisture, air movement, application methods, and <br />finishing techniques, will contribute to the end look of the finished <br />product. Consistency in areas mentioned above typically yield a <br />relatively uniform result. However, color uniformity of AQUAFIN®-1K is <br />not guaranteed. <br />• AQUAFIN®-1K should be applied to the entire wall surface in order to <br />perform effectively. It is not designed to be applied in a small limited <br />treatment area (such as application only over joints and cracks). <br />• AQUAFIN®-1K is not designed for use as a pedestrian traffic coating. <br />For applications in areas that will receive foot traffic, contact your local <br />AQUAFIN Representative about Aquafin Pedestrian Traffic Coatings <br />and Interior Epoxy Floor Coatings. <br />Page 3 of 4 <br />(06/29/26-EK,AC)</p> <p>AQUAFIN®-1K <br />• AQUAFIN®-1K is not a replacement for proper repairs on damaged, <br />deteriorated, or cracked concrete or masonry structures. <br />• If structural repairs are needed, consult a licensed Engineer and ask <br />an Aquafin Representative about Aquafin repair mortars such as <br />MORTAR-40 CI. <br />Packaging: <br />Bag: 50 lbs. (22.7 kg) <br />Storage and Shelf Life: <br />Storage: Store AQUAFIN®-1K in unopened, original, undamaged bags in <br />a dry enclosed area, off the ground in temperatures between 55°F –90°F <br />(13°C - 32°C). <br />Shelf Life: 1 year when stored according to conditions listed above. <br />Note: <br />Proper application is the sole responsibility of the user. Applicators <br />are expected to follow ICRI and ACI guidelines, common concrete <br />practices, and other applicable industry standards. Aquafin personnel or <br />representatives are not site inspectors or construction project managers <br />and therefore do not approve surface preparation, mixing, or application <br />of Aquafin products. Site visits by Aquafin personnel or representatives <br />are solely for the purpose of making technical recommendations, not for <br />providing supervision or quality control. <br />General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time of <br />printing. Depending on specific applications, in particular regarding <br />substrates, processing and environmental conditions may affect final results.</p> <p>Safety: <br />Refer to Safety Data Sheet (SDS). <br />KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period <br />of one year from the date of installation to be manufactured free of defects <br />and to be consistent with its technical properties as stated in our current <br />Technical Data Sheet. This product must be used as directed and within its <br />stated shelf life. AQUAFIN, INC. will replace or at our discretion refund the <br />purchase price of any product, excluding cost of labor, which is proven to be <br />defective. Our product recommendations are based on industry standards <br />and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or <br />use of the product. We do not guarantee compatibility of Aquafin products <br />with other brands. For this reason, we strongly recommend application of a <br />sample area at the jobsite to help determine suitability with other products. <br />AQUAFIN, INC. MAKES NO WARRANTY AS TO MERCHANTABILITY <br />OR FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN <br />LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. AQUAFIN, <br />INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. Any claim for a defective <br />product must be filed within 30 days of discovery of a problem, and must be <br />submitted with written proof of purchase. <br />For Professional Use Only.</p> <p>Certified to</p> <p>NSF/ANSI/CAN Standard 61 <br />see www.wqa.org for use restrictions</p> <p>Common Layering Systems over Concrete, CMU Block, Brick, and Rubble Stone with AQUAFIN®-1K: <br />FINISH:</p> <p>AQUAFIN®-1K “as is”</p> <p>Paint</p> <p>Install Tile</p> <p>1st Layer:</p> <p>Repairs, parge coats, reglets, triangular coves/cants, etc. using a suitable Aquafin mortar</p> <p>AQUAFIN®-2K/M</p> <p>2 Layer: 1st coat of AQUAFIN®-1K</p> <p>1st coat of AQUAFIN®-1K</p> <p>1st coat of AQUAFIN®-1K</p> <p>1st coat of AQUAFIN®-1K</p> <p>3rd Layer:</p> <p>2nd coat of AQUAFIN®-1K</p> <p>2nd coat of AQUAFIN®-1K</p> <p>2nd coat of AQUAFIN®-1K</p> <p>2nd coat of AQUAFIN®-1K</p> <p>4th Layer</p> <p>---</p> <p>Water-based breathable acrylic paint</p> <p>Tile with a cement-based tile mortar</p> <p>1st coat of AQUAFIN®-2K/M</p> <p>5 Layer</p> <p>---</p> <p>nd</p> <p>th</p> <p>---</p> <p>---</p> <p>2nd coat of AQUAFIN®-2K/M</p> <p>Notes: It is important to apply materials in the correct sequence. Contact Aquafin Technical Department for layering systems not listed. Aquafin recommends installation of <br />a mock-up (field sample) of min. 100 ft² (9.29 m²) at the project site or other pre-selected area as agreed to by owner’s representative and applicator.</p> <p>AQUAFIN®-1K Application Rate, Consumption & Yield of 50 lb (22.7 kg) bag <br />Number of <br />Coats</p> <p>Approx. Thickness <br />per Coat</p> <p>Total Thickness (2 coats)</p> <p>Application Rate <br />(dry powder)</p> <p>Approx. Yield <br />per Bag</p> <p>inch</p> <p>mils</p> <p>mm</p> <p>inch</p> <p>mils</p> <p>mm</p> <p>lb/yd²</p> <p>kg/m²</p> <p>ft²</p> <p>m²</p> <p>Dampproofing</p> <p>2</p> <p>1/32”</p> <p>30</p> <p>0.8</p> <p>1/16”</p> <p>60</p> <p>1.6</p> <p>4.6</p> <p>2.5</p> <p>98</p> <p>9.1</p> <p>Waterproofing</p> <p>2</p> <p>1/20”</p> <p>50</p> <p>1.25</p> <p>1/10”</p> <p>100</p> <p>2.5</p> <p>7.4</p> <p>4.0</p> <p>60</p> <p>5.6</p> <p>Base Coat Prior <br />to AQUAFIN®2K/M</p> <p>2</p> <p>1/32”</p> <p>30</p> <p>0.8</p> <p>1/16”</p> <p>60</p> <p>1.6</p> <p>4.6</p> <p>2.5</p> <p>98</p> <p>9.1</p> <p>Notes: Application rates and yield values are approximate. Actual coverage may vary due to absorption of substrate and substrate profile. Failure to achieve the required mil thickness will compromise the effectiveness of the product and void the warranty. It is the applicator’s responsibility to verify that the required mil thickness has <br />been attained. Mils are based on WFT (wet film thickness). <br />Check our website for the latest version of the Technical Data Sheet. Only the current version is legally binding and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 4 of 4 <br />www.aquafin.net <br />(06/29/26-EK,AC)</p>
