Aquafin-2KM_022423 TDS.pdf
4 Pages
610 KB
Download
<h1>Aquafin-2KM_022423 TDS.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>AQUAFIN®-2K/M</p> <p>Flexible Cementitious Protective & Waterproof Coating/Membrane <br />CSI Div. 07 + 09 <br />07 16 14 Acrylic Modified Cement Waterproofing <br />09 97 32 Concrete and Masonry Coatings <br />LEED Points <br />MR Credit 5.1, Regional Materials:…..................…. Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials, Paints and Coatings: 1 Point</p> <p>Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />AQUAFIN-2K/M (in short 2K/M) is a state-of the art, asbestos free, <br />cementitious, acrylic emulsion based, flexible protective coating and <br />waterproof barrier. This product is two-component (powder and liquid) and <br />resistant to water and mild abrasion. <br />Typical Applications: <br />• Above or below grade exterior applications. <br />• Horizontal, vertical, or overhead applications to concrete, cementitious <br />overlays, masonry, brick and parging (render). <br />• Above grade block (CMU) and concrete substrates as a waterproofing <br />base coat under stucco/texture coats. <br />• Exterior waterproofing of new or old below grade foundations. <br />• Terraces and balconies over unoccupied space (stand-alone or under <br />tiles), parapets, planter boxes, plaza decks, stadiums. <br />• Mechanical & equipment rooms. <br />• Underneath flexible thin-set tile mortars (i.e. shower pans, sanitary rooms, <br />kitchens, balconies, etc.). <br />• Potable water, wastewater, sea water and marine aquarium tanks and <br />other reinforced concrete structures. <br />Advantages: <br />• Self curing, 2-component waterproofing membrane <br />• Solvent Free - 0g/L VOC <br />• Potable water NSF/ANSI 61certified by WQA <br />• Does not support the growth of mold & mildew <br />• Meets or exceeds ANSI A118.10 and 12 <br />• UV, weather & freeze/thaw resistant <br />• Breathable (not a vapor barrier) <br />• Applied to moist/damp substrates <br />• Resists strong positive side hydrostatic pressure <br />• Active barrier to carbon dioxide (CO2) <br />• Carbonation protection and carbon dioxide-screen: 40 mils (1 mm) <br />2K/M thickness warrants same protection as 12” (300 mm) of <br />concrete. <br />Substrate Preparation: <br />The substrate must be sound, clean, and free from voids, bug holes, gaping <br />cracks, honey combs, or ridges and open pored (like medium grit sand <br />paper). <br />• Remove bond breakers, such as oil, grease, dirt, loose particles, remains <br />of form oils, water repellents, rust or other coatings by high pressure <br />Check our website for the latest version of the Technical Data Sheet. <br />www.aquafin.net</p> <p>Physical & Technical Data <br />AQUAFIN-2K/M: Dry Powder Component-A <br />Aggregate State:</p> <p>Gray & White</p> <p>Bulk Density:</p> <p>~88 lb/ft³ (~1.4 kg/dm³)</p> <p>Liquid Component-B <br />Aggregate State:</p> <p>White liquid</p> <p>Density at 68°F (20°C):</p> <p>~8.74 lb/gal (~1.05 kg/L)</p> <p>pH-value:</p> <p>7.5</p> <p>AQUAFIN-2K/M: Wet Mix <br />Density of wet mix:</p> <p>~100 lb/ft³ (~1.6 kg/dm³)</p> <p>Pot life (approximate):</p> <p>60 min. at 73° F (23° C) 60% RH <br />20 min. at 95° F (35° C) 65% RH</p> <p>Application Temperature:</p> <p>40° F to 95° F (+5° C to +35° C)</p> <p>VOC:</p> <p>0% (0 g/L)</p> <p>AQUAFIN-2K/M: Cured <br />Color:</p> <p>Gray, white or pigmented</p> <p>Shore ‘A’ Hardness:</p> <p>~85 (ASTM D-2240)</p> <p>Service Temperature: <br />• Traffic: <br />• Non-traffic</p> <p>5° F – 122° F (-15° C – +50° C) <br />-4° F – 140° F (-20° C – +60° C)</p> <p>Elongation at rupture at <br />80 mils (2 mm) thickness: <br />(ASTM D-412-98a)</p> <p>70% Gray at 73° F (23° C) <br />40% White (all without fabric)</p> <p>Crack Bridging Capacity:</p> <p>1/16” (1.6 mm) at 60 mils DFT</p> <p>Tensile Strength: <br />(ASTM D– 412-98a)</p> <p>600 psi (4.2 MPa) @ 80 mils <br />(2 mm) thickness at 73° F (23° C)</p> <p>Adhesion to concrete: <br />(ASTM C-297 modified)</p> <p>145 psi (1.0 MPa) @ 7 d <br />215 psi (1.5 MPa) @ 28 d</p> <p>Abrasion Resistance: <br />(ASTM D-4060)</p> <p>109 mg/1000 cycles, CS-17 wheel <br />(Taber 5150 Abrader)</p> <p>Rapid Chloride Permeability <br />• Untreated control: <br />• 80 mils (2 mm) thickness: <br />Percentage Reduction:</p> <p>Chloride Penetration: <br />3750 Coulombs <br />509 Coulombs <br />86% <br />(ASTM C-1202.97)</p> <p>Flammability: (ASTM E-108)</p> <p>Passed: Class A, Spread of Flame</p> <p>Static Coefficient of Friction: <br />Dry: with sealer CS/250 <br />Wet: with sealer CS/250</p> <p>Non-slip - (ASTM C-1028) <br />1.2 (ADA: 0.8 for ramps) <br />0.9 (ADA: 0.6 or higher)</p> <p>waterblasting (>5000 psi (34.5 MPa)) or wet or dry sandblasting. <br />• Prepare surfaces by mechanical means to obtain a concrete surface <br />profile (CSP) of 3 - 5 per ICRI Guideline No. 310.2-R-2013. <br />Page 1 of 4</p> <p>(02/24/23-EK,VB, AC)</p> <p>AQUAFIN®-2K/M <br />• Repair holes, defects, irregular surfaces, weak mortar joints, etc. with <br />MORTAR-40 CI, MORTAR-V/O CI or MORTAR-LN. <br />• Round edges at vertical external joints. <br />• Close large open pores and joint recesses of CMU blocks and joint <br />unevenness in brick walls with MORTAR-V/O. <br />• Dampen substrate with clean water to saturated surface dry (SSD) <br />condition, with no standing surface water. <br />• Roughen fiberglass substrates using diamond grinding, zek/wire wheel, <br />etc. and clean with acetone prior to applying 2K/M. <br />Mixing: (SEE LAST PAGE FOR STEP-BY-STEP ILLUSTRATION) <br />Mixing ratio by volume: ~5:3 (powder to liquid) <br />• Pigmenting: When using liquid pigments with AQUAFIN-2K/M White, <br />add and mix the liquid pigments with liquid Component-B prior to mixing <br />Component-A with Component-B. <br />• Pour 2/3 liquid Component-B into a clean container, add 2K/M <br />powder (Comp-A) and mix to a lump free creamy consistency. Add <br />remaining 1/3 liquid and mix total 2 - 3 minutes with a strong, slow <br />speed (300 rpm) mechanical mixer. <br />NOTE: In hot weather conditions water can be added after initial mixing to <br />adjust application consistency as follows: <br />max. 10 fl. oz. (0.3 L) per 46 lb (21 kg) unit <br />max. 16 fl. oz. (0.5 L) per 77lb (35 kg) unit. <br />Application: <br />NOTE: Do not apply 2K/M at temperatures below 40°F (5°C) or <br />to frozen substrates. Can be applied to 3 day old concrete at >86°F <br />(>30°C) temperature and 5 day old at 60-70°F (15-21°C), or when <br />concrete reaches minimum 2,000 psi (13.8 MPa). <br />• Application tools: 2K/M may be applied by brush, roller, trowel or <br />appropriate compressed-air spray equipment. Do not pre-dampen brush <br />or roller with water. <br />• Negative Side Waterproofing: AQUAFIN-2K/M is not resistant to <br />negative side water pressure. Substrates prone to negative side water <br />infiltration must be treated with a product designed to resist negative side <br />water pressure, such as AQUAFIN-1K, prior to installation of AQUAFIN2K/M. <br />• Static cracks: Repair static (non-moving) cracks with AQUAFIN <br />CRACK SEALING TAPE (80% elongation), or rout (cut) out and fill with <br />MORTAR-V/O and cover with 2K/M. <br />• Dynamic cracks: Seal dynamic (moving) cracks with JOINT SEALING <br />TAPE-2000-S (600% elongation). <br />• Horizontal and vertical control joints: Seal horizontal wall-floor joints and <br />internal vertical corners with JOINT SEALING TAPE 2000-S. Alternative: <br />form cove (minimum 1.5“ x 1.5“ [38 x 38 mm] with MORTAR-LN or <br />MORTAR-V/O. <br />• Expansion joints: Seal non-traffic bearing expansion joints with JOINT <br />SEALING TAPE-2000-S. <br />Note: 2K/M applied over all tapes in visible areas will <br />crack over the tape due to substrate movement. However, <br />the tape and the structure will still be waterproof. Therefore, wherever <br />aesthetics are important (i.e. walkways, decks, patios, etc.) honor all joints <br />& cracks with an appropriate elastomeric joint sealant or pre-manufactured <br />joint profile. <br />• Construction & Movement joints under Tile: Ensure that construction and <br />movement joints in tiles or stones are foreseen as per industry standards <br />such as per ANSI specification A108.01-3.7 “Requirements for <br />Movement Joints: Preparations by Other Trades” or TCNA detail EJ-171 <br />“Movement Joints-Vertical & Horizontal”. <br />• PVC pipe penetrations & stainless steel flanges: Abrade (sand) PVC <br />pipes and stainless steel flanges and degrease with isopropanol or <br />acetone. Apply 2K/M and embed SEALING GASKET-18/18 or <br />JOINT SEALING TAPE-2000-S as per TDS. <br />Check our website for the latest version of the Technical Data Sheet. <br />www.aquafin.net</p> <p>Vapor Permeability <br />• Untreated control: <br />• 1/16” (1.6 mm) thickness: <br />• 3/32” (2.4 mm) thickness:</p> <p>(ASTM E-96) <br />10.3 perms (100%) <br />2.3 perms <br />(22.3%) <br />1.4 perm <br />(13.6%)</p> <p>Water Permeability: <br />(CRD-C 48-92 at 1/16” <br />(1.6 mm) thickness)</p> <p>No measurable leakage up to 200 <br />psi (460 feet (140 m)) head <br />pressure (positive side).</p> <p>Root Resistance: <br />(EMPA test)</p> <p>No punctures, tested with Lupinus <br />albus</p> <p>Adhesion of Tiles: ANSI A118.10 Results <br />Fungus & Micro-Organism <br />Resistance: test period 14 d</p> <p>Fungus: Aspergillius Niger <br />Pass. No growth was observed</p> <p>Seam Strength: <br />(ASTM-D 751)</p> <p>14.9 lb (6.8 kg) = Pass <br />Requirement 8 lb (3.6 kg)</p> <p>Breaking Strength: <br />(ASTM-D 751)</p> <p>677 psi (4.7 MPa) = Pass <br />Requirement 170 psi (1.2 MPa)</p> <p>Dimensional Stability: <br />+158°F (70°C) <br />-15°F (-26°C) <br />(ASTM-D 1204)</p> <p>Pass <br />0.000% <br />0.000% <br />Requirement: 0.7% maximum</p> <p>Waterproofness: <br />(ASTM-D 4068-99)</p> <p>Pass <br />2’(0.6 m) water column over 48 hr</p> <p>7-Day Shear Strength: <br />(ASTM-C 482-1996)</p> <p>107 psi (0.74 MPa) = Pass <br />Required = 50 psi</p> <p>7-Day Water Immersion <br />Shear Strength: (C 482)</p> <p>86 psi (0.59 MPa) = Pass <br />Required = 50 psi</p> <p>28-Day Shear Strength: <br />(ASTM-C 482-1996)</p> <p>107 psi (0.74 MPa) = Pass <br />Required = 50 psi</p> <p>45-Day Shear Strength: <br />(ASTM-C 482-1996)</p> <p>114 psi (0.79 MPa) = Pass <br />Required = 50 psi</p> <p>100-Day Water Immersion <br />Shear Strength: (C 482)</p> <p>166 psi (1.15 MPa) = Pass <br />Required = 50 psi</p> <p>Adhesion of Tiles: ANSI A118.12 Results <br />Point Load Resistance Test:</p> <p>Pass (after 28 day cure)</p> <p>Compressive Strength:</p> <p>5,000 psi (34.5 MPa) calculated <br />from Point Load Resistance Test</p> <p>System Crack Resistance <br />Test:</p> <p>Standard Performance Requirement <br />1/16” (1.6 mm) = Pass</p> <p>Adhesion to Steel: <br />(ASTM D-4541)</p> <p>250 psi (1.7 MPa) cohesive failure <br />(in-house testing)</p> <p>All data are averages of several tests under laboratory conditions. In practice <br />climatic variations such as temperature, humidity, and porosity of substrate may <br />affect these values.</p> <p>• Alkali sensitive substrates: Protect and seal alkali sensitive metal <br />substrates such as copper, aluminum, galvanized or zinc treated metal <br />first with a primer (i.e. KRYLON Primer, or equal) prior to applying (overcoating) 2K/M. <br />• Reinforcement Mesh: Contact Aquafin Technical Department. <br />• Protect areas not to be treated from 2K/M. Hardened 2K/M can only <br />be removed mechanically. <br />Applications: <br />1. Standard Application: Apply 2K/M in two coats as specified. High <br />Page 2 of 4</p> <p>(02/24/23-EK,VB, AC)</p> <p>AQUAFIN®-2K/M <br />ambient temperatures can create flash setting when product leaves the <br />spray nozzle, creating pinholes in the applied layer. If applied in full <br />sunshine product can skin-up on the surface and de-bond, resulting in <br />post-bubbling. <br />•A <br /> pply 1st coat by brush to force material into the substrate. <br />• Apply 2nd coat (or multiple coats) as soon as the 1st coat has sufficiently <br />hardened (approx. 4–6 hrs @ 68°F (20°C)/63% RH) or max. 24 <br />hours. Do not pre-dampen 1st or following coats. (If longer than 24 <br />hours, 2KM surface must be prepared by high pressure water blasting <br />or sanding/roughening and allowed to dry). Apply by brush, roller, <br />trowel or appropriate compressed-air spray equipment. If sprayed, <br />even out and seal surface by back-troweling, brushing, rolling to <br />achieve a void-free membrane. <br />• Thickness: 60 mils = 2x30 mils (2x0.8 mm) <br />80 mils = 2x40 mils (2x1.0 mm) <br />90 mils = 2x45 mils (2x1.1 mm). <br />2. CMU Block Substrates, 120 mils [1/8”] (3.2 mm): <br />• Apply 2K/M in two coats at total 60 mils (1/16” (1.6 mm))thickness <br />as per item 1. <br />3. Potable water holding tanks. Can be carefully filled after 3 days. Do not <br />fill large tanks faster than 6½ feet per 24 hrs. (2 m/24 hrs). <br />4. Marine aquarium and zoo tanks: <br />• Structure coat containing waterproofing admixtures: verify with <br />admixture manufacturer that cementitious top coatings will bond to the <br />concrete surface prior to installation of 2K/M. Aquafin recommends <br />AQUAFIN-IC-ADMIX (liquid or powder). <br />• Overlaying texture coat: Let 2K/M cure for at least 3—5 days before <br />applying texture coat. Ensure that proper measures are taken to avoid <br />shrinkage of the overlaying “texture coat”. Internal stresses of shrinking <br />“texture coat” can negatively affect the bond to 2K/M, or the integrity <br />of the 2K/M. <br />Exposure(at 68°F {20°C} and 60% humidity) of Application <br />to: <br />• Rain: vertical surfaces after ~3 hrs, horizontal surfaces min. 6 hrs. <br />• Foot traffic: after ~24 hrs. <br />• Flexible tile mortar and tiles: after ~1 day. <br />• Positive side hydrostatic pressure: after 2K/M reaches min. Shore A <br />Hardness 80, check with “finger-nail test”. Typically 3–7 days <br />• Back filling: after ~3 days. <br />Sealing & Protecting: <br />• Clear sealer: In areas such as walkways, balconies, etc. where higher <br />than usual surface contamination can be expected, the surface of 2K/M <br />can be sealed with a clear acrylic sealer. The 2K/M should be cured <br />for min. 24 hrs. before applying sealer. <br />• Painting: Cured 2K/M can be painted with a water-based, “breathable” <br />acrylic paint after 3 days (at 68°F (20° C). <br />Clean-Up: <br />Clean tools and equipment with water immediately after use. Cured <br />material can only be removed mechanically or with a soy based paint <br />remover. <br />Curing & Protection: <br />• Self curing, do NOT use water. It may discolor pigmented applications <br />during the fresh stage. Provide suitable protection against extreme <br />weather conditions while curing. <br />• Expect prolonged setting and hardening time in rooms with high <br />humidity, poorly ventilated areas and corners (i.e. water tanks, etc.). The <br />use of fans will accelerate the setting and curing time. <br />• Attach drainage and protection boards after full curing (3 days). DO <br />NOT mechanically attach. <br />Check our website for the latest version of the Technical Data Sheet. <br />www.aquafin.net</p> <p>Chemical Resistance <br />Acid Solution (pH 2.5), Alkali Solution (pH 11.5), Solvent (90% <br />Acetone)</p> <p>*)</p> <p>Aqueous ammonia, Aqueous sodium hydroxide, Silage</p> <p>+</p> <p>Aqueous magnesium sulfate, Aqueous sodium chloride solution, <br />Aqueous sodium sulfate, Diesel, Hydraulic Oil, Olive oil, Salt water (Sea water) & Marsh Water, Sewage (domestic), Transformer <br />oil, Water</p> <p>++</p> <p>Citric acid, Formic acid, Fuel (hydrocarbons, benzene containing), Inorganic acids, Mineral oil</p> <p>-</p> <p>*) = Slight discoloration after 48 hrs (ASTM D-543 spot test) <br />+ = Short Term Resistance - splashes and spills <br />++ = Long Term - Permanent Resistance <br />- = Not Resistant <br />Limitations: <br />• Do NOT use 2K/M in pools, hot tubs, or fountains. <br />• Do not use as an adhesive to install ceramic tile or natural stone. <br />• Do not use as a roofing membrane or in lieu of a roofing membrane. <br />• Do not install directly over single layer wood floors. <br />• Protect application from direct sunlight and wind to prevent premature <br />surface drying, bubbling and shrinkage cracks. <br />• Do NOT directly apply 2K/M over AQUAFIN-IC or similar crystalline <br />waterproofing products. <br />• Do not use solvent based adhesives, epoxies, etc. directly on 2K/M. <br />• Do not expose the application to water during the setting time. <br />• Soft water: contact our office if water hardness is <30 mg CaO/L. <br />• Product can be tinted (pigmented), however, color uniformity cannot <br />be guaranteed. Note: color fading of pigmented product will occur in <br />submerged zones with water containing increased chlorine or ozone <br />concentrations. <br />Maintenance: <br />Mechanically damaged 2K/M can be easily repaired by thoroughly <br />cleaning (sanding) the surface and reapplying a new coat of 2K/M. <br />Packaging: <br />• 46 lb (21 kg) Comb-unit: 5 gal pail containing bag + pail <br />A-Component (powder): 33 lb (15 kg) bag <br />B-Component (liquid): 1.5 gal / 13 lb pail (5.7 L /6 kg) <br />• 77 lb (35 kg) Unit: bag + pail separate <br />A-Component (powder): 55 lb (25 kg) bag <br />B-Component (liquid): 2.5 gal / 22 lb pail (9.5 L /10 kg) <br />Note: Pigments for tinting 2K/M are packaged separately. <br />Shelf Life: <br />Approx. 12 months for powder Component-A and up to 24 months for <br />liquid Component-B in unopened packaging, stored dry, cool and <br />frost-free. <br />Note: <br />Proper use is the responsibility of the applicator. Applicators are expected <br />to know and follow industry standards. Site visits by Aquafin personnel <br />or representatives are solely for the purpose of making technical <br />recommendations, not for providing supervision or quality control. This <br />product is not sold to the Do-it-Yourself market. For Professional Use <br />Only.</p> <p>Page 3 of 4</p> <p>(02/24/23-EK,VB, AC)</p> <p>AQUAFIN®-2K/M <br />General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time <br />of printing. Depending on specific applications, in particular regarding <br />substrates, processing and environmental conditions may affect the final <br />results. <br />Safety: Refer to SDSs. For commercial use only. <br />A-Component (powder) contains sand (crystalline silica) and Portland <br />cement and is highly alkaline (irritant) in contact with water. Prevent <br />inhalation of dust before and during mixing with liquid Component-B. <br />B-Component (liquid) contains no hazardous materials. Use rubber gloves <br />and goggles during mixing and application. Avoid contact with eyes and <br />skin. After contact with skin, wash with plenty of water. In case of eye <br />contact, rinse immediately with plenty of water and seek medical advice. In <br />case of handling large quantities, provide good ventilation if indoors. <br />KEEP OUT OF REACH OF CHILDREN.</p> <p>LIMITED WARRANTY: AQUAFIN, INC. warrants its products to be manufactured free of defects <br />for one year and to be consistent with its standard high quality. We will replace or, at our election, <br />refund the purchase price of, any product which is proven to be defective, provided that the <br />product was properly applied. Our product recommendations are based on Industry Standards <br />and testing procedures. We assume no warranties either written, expressed or implied as to <br />any specific methods of application or use of the product. We do not guarantee compatibility <br />of Aquafin products with other brands. For this reason, we strongly recommend application of <br />a sample area at the jobsite to help determine suitability with other products. AQUAFIN, INC. <br />MAKES NO WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR <br />PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR <br />IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay.</p> <p>Certified to <br />NSF/ANSI Standard 61 <br />see www.wqa.org for use restrictions</p> <p>Consumption & Yield Do not exceed total thickness of 100 mils (2.5 mm) for 2K/M. <br />Application Condition Note: All coverage rates are listed at 2 coats. Do not apply 2K/M thicker than 45 mils</p> <p>Min. coating thickness DFT <br />(dry film thickness) <br />inch [ mils ] ( mm )</p> <p>46 LB UNIT <br />Appx. Yield <br />ft² ( m² )</p> <p>77 LB UNIT <br />Appx. Yield <br />ft² ( m² )</p> <p>• E xposed applications: walkways, balconies, mechanical rooms, planters <br />•W <br /> aterproofing, exterior above & below grade applications with water depth less than 13 ft.</p> <p>~1/16“ [ 60 ] (1.6 )</p> <p>75 ( 7.0 )</p> <p>125 (11.6 )</p> <p>•A <br /> pplications under tile: balconies, plaza decks <br />•W <br /> aterproofing, exterior above & below grade applications with water depth more than 13 ft.</p> <p>~1/12“ [ 80 ] (2.0 )</p> <p>56 ( 5.1 )</p> <p>94 ( 8.7 )</p> <p>~1/16“ [ 60 ] (1.6 ) <br />~1/16“ [ 60 ] (1.6 )</p> <p>98 ( 9.1 ) <br />75 ( 7.0 )</p> <p>98 ( 9.1 ) <br />125 (11.6 )</p> <p>~3/32“ [ 90 ] ( 2.25 )</p> <p>50 ( 4.7 )</p> <p>84 ( 7.8 )</p> <p>per coat. (Thickness: 60 mils = 2x30 mils (2x0.8 mm), 80 mils = 2x40 mils (2x1.0 mm), 90 mils = 2x45 mils (2x1.1 <br />mm).)</p> <p>•W <br /> aterproofing, interior below grade structures & all in-ground water tanks, etc.: <br />Base coat: AQUAFIN-1K (50 lb bag (22.7 kg)) <br />Top coat: AQUAFIN-2K/M applied in 2 coats</p> <p>•A <br /> quarium & Zoo Tanks: Refer to Spec Sketch No.1.1.3-10.</p> <p>Refer to waterproofing specification sketches no. 1.1.3. Failure to achieve the required DFT (dry film thickness) will compromise the effectiveness of the product and void the warranty. Yield values are <br />approximate. Variations may apply due to substrate conditions or conversion factors.</p> <p>Mixing: Mixing ratio by volume: ~5:3 (powder to liquid) <br />1. IF Pigmenting: Add and <br />mix liquid pigment with <br />liquid Component-B prior to <br />mixing Component-A with <br />Component-B.</p> <p>2. Pour 2/3 liquid Component-B into a clean container. Add 2K/M <br />powder (Comp-A) and mix to a lump free creamy consistency with a strong, <br />slow speed (300 rpm) mechanical mixer.</p> <p>COMP <br />A <br />100%</p> <p>COMP <br />B <br />66%</p> <p>3. Add remaining 1/3 liquid and <br />mix total 2 - 3 minutes.</p> <p>COMP <br />B</p> <p>COMP <br />B</p> <p>4. NOTE: In hot weather conditions, water can be added after initial mixing to adjust application consistency: <br />max. 10 fl.oz. (0.3 L) per 46 lb (21 kg) unit Max. 16 fl. oz. (0.5 L) per 77lb (35 kg) unit. Add water and mix for an additional 1 - 2 minutes. <br />Check our website for the latest version of the Technical Data Sheet. Only the current version is legally binding and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 4 of 4</p> <p>(02/24/23-EK,VB, AC)</p>
