AQUAFIN-2KM waterproofing specification sketches - 070414.pdf
17 Pages
591 KB
Download
<h1>AQUAFIN-2KM waterproofing specification sketches - 070414.pdf</h1> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>AQUAFIN-2K/M <br />FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Typical Waterproofing Specifications</p> <p>Table of Contents:</p> <p>No.</p> <p>Waterproofing Specification</p> <p>Specification No.</p> <p>1 <br />2 <br />3 <br />4 <br />5 <br />6 <br />7 <br />8 <br />9 <br />10 <br />11 <br />12 <br />13 <br />14 <br />15 <br />16</p> <p>Exterior waterproofing of CMU or brick walls <br />Interior waterproofing of existing foundation wall & slab <br />Exterior waterproofing of concrete walls <br />Waterproofing of tiled swimming pool <br />Waterproofing of fountain / decorative water feature <br />Waterproofing of open or vented sewage and other tanks <br />Waterproofing of a planter <br />Waterproofing of covered underground parking garage deck <br />Waterproofing under topping slabs or pavers <br />Waterproofing of marine aquarium and zoo concrete tanks <br />Waterproofing of tiled balcony <br />Waterproofing of tiled fountain <br />Waterproofing/protecting of non-tiled balcony <br />Typical sealing around pipe penetrations <br />Waterproofing of construction joints, expansion joints & cracks <br />Waterproofing of wall / floor expansion joint</p> <p>1.1.3 - 1 <br />1.1.3 - 2 <br />1.1.3 - 3 <br />1.1.3 - 4 <br />1.1.3 - 5 <br />1.1.3 - 6 <br />1.1.3 - 7 <br />1.1.3 - 8 <br />1.1.3 - 9 <br />1.1.3 - 10 <br />1.1.3 - 11 <br />1.1.3 - 12 <br />1.1.3 - 13 <br />1.1.3 - 14 <br />1.1.3 - 15 <br />1.1.3 - 16</p> <p>Note: These specification sketches have been prepared with our best knowledge and experience available at the time of publishing. As technology <br />advances and construction methods change we may have to update them. We therefore kindly ask the user to check the date on this page of this issue <br />and to re-check with us whether you have the latest edition. It is our goal to serve you and the construction industry as best as possible. <br />Copyright 2006, Aquafin, Inc. - Revision 07/04/14</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 info@aquafin.net http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 1</p> <p>Building <br />Product Systems</p> <p>EXTERIOR WATERPROOFING OF CMU OR BRICK WALLS <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketches</p> <p>1</p> <p>Above grade</p> <p>2</p> <p>///=///=///=///=///=///= <br />Below grade</p> <p>2 <br />3 <br />4 <br />0</p> <p> Seal exterior cracks, vertical and horizontal joints with AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING <br />TAPE. <br />Alternative: form cove of AQUAFIN MORTAR-LN or MORTAR-40 at wall/foundation joint.</p> <p> Seal porous surfaces and mortar joints with one scratch coat AQUAFIN-1K or approx. 60 mils (1/16”) thickness <br />[1.6 mm].</p> <p> Apply AQUAFIN-2K/M to walls at 1/16” [60 mils] (1.6 mm) total thickness. Apply base coat by brush ensuring good <br />adhesion. Apply top coat with brush, roller, trowel or spraying. Smooth with a trowel if desired.</p> <p> If desired, embed AQUAFIN-4x4-MESH to increase tear resistance into 1st coat of AQUAFIN-2K/M using a steel <br />trowel. Cover with 2nd coat AQUAFIN-2K/M.</p> <p>Note: <br />In areas with poor drainage or where high hydrostatic pressure is anticipated, increase total application rate of <br />AQUAFIN-2K/M to 80 - 90 mils (2.0 - 2.25 mm). <br />Refer to product data sheet for further information. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 info@aquafin.net http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p> Install protection boards or drain mats before backfilling.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 2</p> <p>Building <br />Product Systems</p> <p>INTERIOR WATERPROOFING OF EXISTING FOUNDATION WALL & SLAB <br />Schematic sketches</p> <p>///=///=///=///=///</p> <p>1</p> <p>eg <br />le <br />co t o <br />ve r</p> <p>2 <br />0</p> <p>R</p> <p>Brick <br />Stone <br />CMU <br />Concrete</p> <p> Install sealing reglet (~1” x 3/4”) or cove (~1.5” x 1.5”) with AQUAFIN-MORTAR-LN at wall/slab joints. <br /> <br />A. Brick and stone rubble walls: <br />a. Level surface and mortar joints with minimum 1/2” (12 mm) thick MORTAR-LN. <br />b. Apply 1-2 coats AQUAFIN-1K (gray or white) at total 1/16” [60 mils] (1.6 mm) thickness. <br />B. CMU block walls: <br />a. Apply 2 coats AQUAFIN-1K (gray or white) at total 1/16” [60 mils] (1.6 mm) for dampproofing or <br />1/10” [100 mils] (2.5 mm) for waterproofing. <br />C. Concrete walls: <br />a. Apply 2 coats AQUAFIN-IC (gray or white) at total 1/32” [32 mils] (0.8 mm) thickness (2.8 lb/yd2 (1.5 kg/m2)). <br />Alternative for aesthetic appearance: <br />a. Apply 2 coats AQUAFIN-1K (gray or white) at total 1/16” [60 mils] (1.6 mm) for dampproofing or 1/10” [100 mils] (2.5 mm) for <br />waterproofing.</p> <p>VAPORTIGHT COAT7-SG3 vapor and moisture emission barrier if vapor emission exceeds 3 lbs/24 hrs•1000 ft2 (0.6 g/hr •m2) or <br />>75% RH as per ASTM F-2170. <br />Refer to product data sheets for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 11/13</p> <p> For basements being converted to offices or habitable areas that will receive carpeting, VCT, hardwood flooring, etc. install AQUAFIN</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 3</p> <p>Building <br />Product Systems</p> <p>EXTERIOR WATERPROOFING OF CONCRETE WALLS <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketches</p> <p>Above grade</p> <p>1 <br />2</p> <p>///=///=///=///=///=///= <br />Below grade</p> <p>2 <br />1</p> <p>3 <br />4 <br />0</p> <p> Seal exterior cracks, vertical and horizontal joints with AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING <br />TAPE. <br /> Alternative: form cove of AQUAFIN MORTAR-LN or MORTAR-40 at wall/foundation joint.</p> <p> Seal (“sack”) “bug holes” with AQUAFIN-1K. Use MORTAR-LN or MORTAR-40 for patching honey combs. <br /> Apply AQUAFIN-2K/M to walls at 1/16” [60 mils] (1.6 mm) total thickness. Apply base coat by brush ensuring good <br />adhesion. Apply top coat with brush, roller, trowel or spraying. Smooth with a trowel if desired.</p> <p> If desired, embed AQUAFIN-4x4-MESH into 1st coat of AQUAFIN-2K/M using a steel trowel. Cover with 2nd coat <br />AQUAFIN-2K/M. Contact Aquafin office for recommendations.</p> <p> Install protection boards or drain mats before backfilling.</p> <p>Refer to product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p>Note: <br />In areas with poor drainage or where high hydrostatic pressure is anticipated, increase total application rate of <br />AQUAFIN-2K/M to 80 - 90 mils (2.0 2.25 mm).</p> <p>AQUAFIN <br />AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 4</p> <p>Building <br />Building <br />ProductSystems <br />Systems <br />Product</p> <p>WATERPROOFING OF TILED SWIMMING POOL - AQUAFIN-2K/M <br />Schematic sketches</p> <p>Cast-in-place</p> <p>Water level</p> <p>Detail</p> <p>Above ground: <br />Base + top coat: <br />AQUAFIN-2K/M</p> <p>1</p> <p>Inground: <br />Base coat: AQUAFIN-1K <br />Top coat: AQUAFIN-2K/M</p> <p>Ceramic tile</p> <p>2</p> <p>tile grout</p> <p>0 <br />Concrete</p> <p>3</p> <p>Flexible thin set tile mortar <br />AQUAFIN-2K/M or <br />AQUAFIN-1K + 2K/M <br />Leveling mortar ("brown coat", etc.) <br />AQUAFIN-WATERSTOP</p> <p>Substrate: Cast-in-place concrete or gunite (shotcrete) <br />Note: Install leveling coats (i.e. “mud bed”, “brown coat”, plaster, etc.,) to the concrete substrate, prior to the application of AQUAFIN-1K and/or AQUAFIN-2K/M.</p> <p> Install AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING TAPE to seal cracks and cold joints and JOINT <br />SEALING TAPE-2000-S to seal expansion joints. Refer to No. 1.1.3-15 for details.</p> <p> Above ground + elevated: Apply AQUAFIN-2K/M to interior pool surfaces in 2 coats at a total thickness of 80 mils <br />(2.0 mm).</p> <p> In-ground: <br /> Apply 1st (base) coat AQUAFIN-1K at 60 mils (1.6 mm); <br /> Apply 2nd (top) coat AQUAFIN-2K/M at 60 mils [1/16”] (1.6 mm) thickness to walls and floor, wherever rain or <br />groundwater (negative side) pressure can be expected (i.e. inground pools, ponds, etc.). This can also apply to <br />gutters. See application rates on AQUAFIN-2K/M data sheet.</p> <p> Install ceramic or glass tiles and tile grout. Observe TCNA Guidelines for movement joint spacing. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p> Apply flexible thin set tile mortar over AQUAFIN-2K/M.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 5</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF DECORATIVE WATER FEATURE <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketches</p> <p>In-ground</p> <p>///=///=///</p> <p>On grade</p> <p>2 <br />1 <br />1 <br />0 a.)</p> <p>0 b.)</p> <p>///=///=/// <br />AQUAFIN-WATERSTOP</p> <p> a.) Install cove with AQUAFIN MORTAR-LN or MORTAR-40 [~1.5” x 1.5”] (~38 x 38 mm) at non-moving (static) <br />wall/slab joints. <br /> b.) Alternative: Seal cracks and non-moving joints with JOINT SEALING TAPE-2000 or CRACK SEALING TAPE and <br />dynamic (expansion) joints with JOINT SEALING TAPE-2000-S. Refer to No. 1.1.3-15 for details.</p> <p> On grade, above ground + elevated: <br />For water levels < 13’ (<4 m) apply AQUAFIN-2K/M to walls and slabs at 1/16” [60 mils] (1.6 mm). <br />In-ground:</p> <p>(negative side) pressure can be expected (i.e. inground structures, etc.). See application rates on AQUAFIN-2K/M data <br />sheet. <br />Wait minimum 24 hrs. before applying top coat over base coat. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p> Apply 1st (base) coat AQUAFIN-1K at 60 mils (1.6 mm). <br /> Apply 2nd (top) coat AQUAFIN-2K/M at 60 mils (1.6 mm) thickness to walls and floor, wherever rain or groundwater</p> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>Waterproofing Specification <br />No. 1.1.3 - 6</p> <p>WATERPROOFING OF OPEN OR VENTED SEWAGE AND OTHER TANKS <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />(Clarifiers, digesters, pumping stations, etc.) <br />Schematic sketches</p> <p>1 <br />0 a.)</p> <p>0 b.)</p> <p>AQUAFIN-WATERSTOP</p> <p> a.) Install cove with AQUAFIN MORTAR-LN or MORTAR-40 at non-moving (static) wall/slab joints. <br /> b.) Alternatively, install AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING TAPE. Use JOINT SEALING TAPE-2000-S <br />at expansion joints. Refer to No. 1.1.3-15 for details.</p> <p> Above ground tanks: Apply AQUAFIN-2K/M to walls and slabs at 3/32” [90 mils] (2.4 mm) total thickness.</p> <p>Note: Use epoxy coatings in H2S environments. <br />Refer to standard specifications and product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p>Inground tanks: Apply 1st (base) coat AQUAFIN-1K at 60 mils (1.6 mm) and 2nd (top) coat AQUAFIN-2K/M at 60 mils <br />[1/16”] (1.6 mm) thickness to walls and floor, wherever rain or groundwater (negative side) pressure can be expected (i.e. <br />inground structures, etc.). See application rates on AQUAFIN-2K/M data sheet.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 7</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF A PLANTER <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketches</p> <p>///=///=///=///</p> <p>///=///=///=///</p> <p>2 <br />1 <br />0</p> <p> Install JOINT SEALING TAPE-2000 or CRACK SEALING TAPE at cold joints and TAPE-2000-S at dynamic <br />cracks and joints. Refer to No. 1.1.3-15 for details.</p> <p> Apply AQUAFIN-2K/M at 1/16” [60 mils] (1.6 mm) in one coat by trowel. Alternatively apply in two <br />brush or roller coats to 1/16” (1.6 mm) thickness. Smooth with a trowel if desired.</p> <p> Static cracks can be covered with AQUAFIN-4x4-MESH.</p> <p>up-date AQ 11/13</p> <p>Refer to product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>Waterproofing Specification <br />No. 1.1.3 - 8</p> <p>WATERPROOFING OF COVERED UNDERGROUND PARKING GARAGE DECK <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketches</p> <p>2</p> <p>Drain mat</p> <p>1</p> <p>0</p> <p> Seal static cracks and construction joints with AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING TAPE. Use <br />JOINT SEALING TAPE-2000-S at expansion joints and dynamic cracks. Refer to No. 1.1.3-15 for details.</p> <p> Apply AQUAFIN-2K/M to walls and slab at 3/32” [90 mils] (2.4mm) in two coats by trowel or spray. <br />If desired, embed AQUAFIN-4x4-MESH into 1st coat of AQUAFIN-2K/M using a steel trowel. Cover with 2nd coat <br />AQUAFIN-2K/M.</p> <p>Refer to product data sheet for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p> Install drain mat, root protection and planting system according to specifications.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 15</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF CONSTRUCTION JOINTS, EXPANSION JOINTS & CRACKS <br />AQUAFIN-2K/M & JOINT SEALING TAPE <br />Schematic sketches <br />Construction Joint or Crack</p> <p>B-1</p> <p>JOINT SEALING TAPE <br />CRACK SEALING TAPE</p> <p>AQUAFIN-2K/M <br />minimum <br />3/4" (20 mm)</p> <p>minimum <br />3/4" (20 mm)</p> <p>Static = TAPE-2000 <br />Dynamic = TAPE-2000-S <br />JOINT SEALING TAPE <br />CRACK SEALING TAPE</p> <p>Expansion joint sealed for interior tank surfaces</p> <p>B-2 Expansion joint exposed to pedestrian traffic or fountains and <br />other water features in visible, decorative areas</p> <p>AQUAFIN-2K/M <br />approx. 1/8" (3.0 mm)</p> <p>minimum <br />3/4" (20 mm)</p> <p>Tape width</p> <p>Wall/floor joint</p> <p>A-2</p> <p>JOINT SEALING TAPE-2000-S <br />minimum <br />3/4" (20 mm)</p> <p>5</p> <p>AQUAFIN-2K/M</p> <p>No Tape</p> <p>Joint sealant</p> <p>Joint sealant or <br />preformed profile</p> <p>A-1 & A-2. Application/Installation steps:</p> <p> <br /> <br /> <br /></p> <p></p> <p>Apply 1st coat of AQUAFIN-2K/M, extending min. 3/4” (20 mm) <br />beyond either side of tape. <br />Instantly embed JOINT SEALING TAPE or CRACK SEALING TAPE <br />uniformly into 1st coat of AQUAFIN-2K/M, leaving no wrinkles. <br />Let 1st coat cure minimum 4-6 hrs and assure that the TAPE is fully <br />bonded before starting the next step. <br />Cover JOINT SEALING TAPE or CRACK SEALING TAPE with 2nd coat <br />of AQUAFIN-2K/M (same or next day) and smooth the surface with <br />a damp brush. <br />Note: Use JOINT SEALING TAPE-2000-S for areas subject to <br />movement. <br />Coating 2K/M over the exposed tape will most likely break. <br />However, tape will not leak.</p> <p>Note: If necessary protect tape from mechanical damage. However, be aware that 2K/M top coat may crack due to larger <br />movement of tape, not affecting the waterproofing process of the tape. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p>approx. 1/10" (2.5 mm)</p> <p>A-1</p> <p>Static (non-moving) = TAPE-2000 <br />Dynamic (moving) = TAPE-2000-S</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 16 <br />15.1</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF WALL / FLOOR EXPANSION JOINT <br />AQUAFIN-2K/M & JOINT SEALING TAPE 2000-S <br />Schematic sketch</p> <p>Expansion joint sealed with 1 tape <br />minimum <br />3/4" (20 mm)</p> <p>Joint Sealing Tape-2000-S <br />3/4" (20 mm) minimum</p> <p>AQUAFIN-2K/M <br />Concrete</p> <p>Concrete</p> <p>Joint packed with compressible fill material <br />Alternative: Backer rod (foam) & elastomeric sealant</p> <p>D. Sealing of wall/floor expansion joints, using 1 tape:</p> <p> Apply 1st coat of AQUAFIN-2K/M, extending min. 3/4” (20 mm) beyond either side of tape. <br /> Immediately embed JOINT SEALING TAPE-2000-S uniformly into 1st coat of AQUAFIN-2K/M, <br />leaving no wrinkles. Allow sufficient slack to accommodate joint movement.</p> <p> Let 1st coat cure minimum 4-6 hrs and assure that the TAPE is fully bonded before starting the next step. <br /> Cover JOINT SEALING TAPE-2000-S with 2nd coat of AQUAFIN-2K/M (same or next day), stopping <br />at joint edge, and smooth the surface with a damp brush. <br />AQ 11/13</p> <p>D.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 14</p> <p>Building <br />Product Systems</p> <p>TYPICAL SEALING AROUND PIPE PENETRATIONS WITH AQUAFIN-2K/M <br />Schematic sketches</p> <p>A. Sealing around steel or concrete pipes <br />Apply AQUAFIN-2K/M <br />surface waterproofing, <br />extending at least 4" (10 cm) <br />onto pipe</p> <p>Steel or concrete pipe <br />4" <br />10 cm</p> <p>B. Sealing around PVC pipes <br />and drains:</p> <p>B.1 <br />4"</p> <p>AQUAFIN-2K/M</p> <p>AQUAFIN SEALING GASKET:</p> <p>(10 cm)</p> <p>Concrete</p> <p>Size: 18” x18” (450 x 450 mm) <br />can be cut to required size and <br />shape</p> <p>.</p> <p>B.1: Pipes < 6" I.D.: <br />Apply AQUAFIN-2K/M surface waterproofing, <br />extending 4" (10 cm) onto pipe.</p> <p>PVC pipe</p> <p>B.1.A.: Alternative: Embed AQUAFIN-SEALING <br />GASKET-18/18 into AQUAFIN-2K/M, flush to pipe. <br />Cove 1.5" x 1.5" <br />MORTAR-LN or 40</p> <p>AQUAFIN-2K/M <br />4" - 6" <br />(10 - 15 cm)</p> <p>B.2: Pipes > 6" I.D.: <br />Install cove of MORTAR-"LN or "40" at pipe penetration. <br />Apply AQUAFIN-2K/M surface waterproofing, <br />extending 4"-6" (100-150 mm) onto pipe. <br />Check possibility of using AQUAFIN SEALING <br />GASKET-18/18, 4x4-MESH or TAPE-2000-S.</p> <p>Note: Mechanically roughen PVC surface and degrease/clean with isopropanol or acetone prior to application of <br />AQUAFIN-2K/M. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 11/13</p> <p>B.2</p> <p>AQUAFIN</p> <p>Building <br />Product Systems</p> <p>Waterproofing Specification <br />No. 1.1.3 - 9</p> <p>WATERPROOFING UNDER TOPPING SLABS OR PAVERS <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketch</p> <p>3 4x4-MESH</p> <p>1 J.S.TAPE-2000-S <br />6 Topping slab</p> <p>or pavers <br />5 Drain/protection <br />board <br />2 + 4</p> <p>90 mils <br />(2.4 mm)</p> <p>AQUAFIN-2K/M <br />Structural slab</p> <p> Seal cracks with AQUAFIN JOINT SEALING TAPE-2000-S as per data sheet. <br /> Apply 1st (base) coat AQUAFIN-2K/M at 45 mils (1.2 mm) thickness. <br /> Immediately embed AQUAFIN-4x4-MESH into fresh (wet) AQUAFIN-2K/M, insuring full saturation. <br /> Apply 2nd (top) coat AQUAFIN-2K/M at 45 mils (1.2 mm) thickness after 1st coat has sufficiently hardened <br />(3 - 5 hrs), depending on temperature, or next day.</p> <p> Install drain/protection board/mat after AQUAFIN-2K/M reaching Shore A Hardness >85 (between 3 - 7 <br />days).</p> <p>Refer to product data sheets for further information.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 11/13</p> <p> Pour topping slab or place precast pavers.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 10</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF MARINE AQUARIUM AND ZOO CONCRETE TANKS <br />AQUAFIN-2K/M FLEXIBLE CEMENTITIOUS WATERPROOFING <br />Schematic sketches</p> <p>A. Shotcrete tanks</p> <p>B. Cast-in place tanks</p> <p>Structural shotcrete wall</p> <p>Structural cast-in-place concrete wall</p> <p>2</p> <p>Texture coat <br />~2" (50 mm) thick <br />applied over minimum <br />3 day cured 2K/M</p> <p>1</p> <p>Optional: <br />Texture coat <br />and/or rock work</p> <p>1 <br />0 <br />AQUAFIN-WATERSTOP</p> <p> Install AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING TAPE or JOINT SEALING TAPE-2000-S (8” wide) depending <br />on expected joint movement. Refer to No. 1.1.3-15 for details. Use in all horizontal and vertical joints and cracks (4.75” <br />wide tape).</p> <p> Apply AQUAFIN-2K/M to walls and slabs at 3/32” [90 mils] (2.4 mm) total thickness. Let cure for minimum 3 days if a</p> <p>Note: For cast-in-place tanks, apply 1st coat AQUAFIN-1K at 60 mils (1.6 mm) and 2nd coat AQUAFIN-2K/M at 60 mils <br />(1.6 mm) thickness to walls and floor, wherever rain or groundwater (negative side) pressure can be expected (i.e. inground <br />structures, etc.). See application rates on AQUAFIN-2K/M data sheet. Call Aquafin for guidance regarding possible use of <br />AQUAFIN-4x4-MESH.</p> <p> For added protection, incorporate AQUAFIN-IC-ADMIX crystalline waterproofing admix where applicable. <br />Refer to standard specifications and product data sheet for further information. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p>texture coat or other topping is to be applied. If a primer is used, apply over dry 2K/M. Prevent texture coat or topping from <br />shrinkage to avoid delamination or damaging the 2K/M.</p> <p>AQUAFIN</p> <p>Waterproofing Specification <br />No. 1.1.3 - 11</p> <p>Building <br />Product Systems</p> <p>WATERPROOFING OF TILED BALCONY - AQUAFIN-2K/M <br />Schematic sketches</p> <p>Bldg. Fassade</p> <p>0</p> <p>1</p> <p>2</p> <p>3</p> <p>Concrete <br />balcony</p> <p> Install AQUAFIN JOINT SEALING TAPE-2000, 8” (200 mm) wide, to seal wall/slab construction joint and JOINT SEALING <br />TAPE-2000-S to seal expansion joints. Refer to No. 1.1.3-15 for details.</p> <p> Apply AQUAFIN-2K/M to slab and wall surfaces in 2 coats at a total thickness of 80 mils (2.0 mm). <br /> Apply flexible thin set tile mortar over AQUAFIN-2K/M. <br /> Install ceramic tile and tile grout as per tile manufacturer. Observe TCNA Guidelines for movement joint spacing.</p> <p> If necessary pitch to floor drain using MORTAR-LN, QUICK-Patch or MORTAR-Screed.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 11/13</p> <p>Note: <br /> The same Aquafin system applies in case of 24” x 24” pavers, set in a mortar bed of minimum 3/4” thickness in lieu of <br />thin set tile mortar.</p> <p>Waterproofing Specification <br />No. 1.1.3 - 12</p> <p>AQUAFIN <br />AQUAFIN</p> <p>Building <br />Building <br />Building <br />Product <br />Product <br />Systems <br />Systems <br />Product <br />Systems</p> <p>WATERPROOFING OF TILED FOUNTAIN - AQUAFIN-2K/M <br />Schematic sketches</p> <p>Water level</p> <p>Detail</p> <p>1</p> <p>///=///=///=/// <br />Ceramic tile</p> <p>2</p> <p>tile grout</p> <p>0</p> <p>3</p> <p>Thin set tile mortar <br />AQUAFIN 2K/M <br />AQUAFIN-WATERSTOP</p> <p> Install AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING TAPE, to seal wall/slab construction joint and JOINT <br />SEALING TAPE-2000-S to seal expansion joints. Refer to No. 1.1.3-15 for details.</p> <p> Above ground + elevated: Apply AQUAFIN-2K/M to interior surfaces in 1 - 2 coats at a total thickness of 60 mils <br />[1/16”] (1.6 mm). <br />Inground: Apply 1st (base) coat AQUAFIN-1K at 60 mils (1.6 mm) and 2nd (top) coat AQUAFIN-2K/M at 60 mils [1/16”] <br />(1.6 mm) thickness to walls and floor, wherever rain or groundwater (negative side) pressure can be expected. See application rates on AQUAFIN-2K/M data sheet.</p> <p> Apply flexible thin set tile mortar over AQUAFIN-2K/M. <br /> Install ceramic or glass tiles and tile grout as per tile manufacturer. Observe TCNA Guidelines for movement joint spacing. <br />AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p>Note: Install leveling coats (i.e. “mud bed”, “brown coat”, plaster, etc.,) prior to the application of AQUAFIN-1K and/or <br />AQUAFIN-2K/M.</p> <p>Waterproofing Specification <br />No. 1.1.3 - 13</p> <p>AQUAFIN <br />AQUAFIN</p> <p>Building <br />Building <br />Product <br />Product <br />Systems <br />Systems</p> <p>WATERPROOFING/PROTECTING OF NON-TILED BALCONY - AQUAFIN-2K/M <br />Schematic sketches</p> <p>Bldg. Facade <br />Oriented Strand Board (OSB) <br />Dense Glass Board <br />Plywood <br />Cement Board</p> <p>0</p> <p>1</p> <p>2</p> <p>concrete <br />balcony</p> <p> Install AQUAFIN JOINT SEALING TAPE-2000 or CRACK SEALING TAPE, to seal wall/slab construction joint and JOINT SEALING <br />TAPE-2000-S to seal expansion and movement joints and cracks. Refer to No. 1.1.3-15 for details.</p> <p> Apply AQUAFIN-2K/M to slab and wall surfaces in 2 coats at a total thickness of 1/16” [60 mils] (1.6 mm). <br /> Protect AQUAFIN-2K/M surface with AQUAFIN-CS/250 clear acrylic sealer or AQUAFIN-Color-Seal pigmented sealer to match</p> <p>Note: <br />If necessary pitch to drain using MORTAR-LN,QUICK-Patch or MORTAR-Screed.</p> <p>AQUAFIN, INC. 505 Blue Ball Rd., #160 Elkton, MD 21921 <br />Phone: (410) 392-2300 FAX: (410) 392-2324 http://www.aquafin.net</p> <p>up-date AQ 07/14</p> <p>existing color of 2K/M.</p>
