TDS-ELASTOSEAL-5000_052025.pdf
4 Pages
109 KB
Download
<h1>TDS-ELASTOSEAL-5000_052025.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />e: info@aquafin.net <br />e: technical@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>ELASTOSEAL-5000</p> <p>Elastomeric, Urethane/Polyurea, Water-activated Waterproofing Membrane <br />CSI Div. 07, 09 + 32 <br />07 14 16 Cold Fluid Applied Waterproofing <br />07 01 50 Maintenance of Membrane Roofing <br />07 50 00 Membrane Roofing <br />07 72 46 Roof Walkways <br />07 76 00 Roof Pavers <br />07 76 16 Roof Decking Pavers <br />09 01 90 Maintenance of Painting and Coating <br />32 94 33 Planters <br />LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />ELASTOSEAL-5000 is a unique single component, cold fluid applied, <br />high performing, elastomeric, urethane and polyurea membrane that uses <br />water as a catalyst. It is designed to function as a specialty waterproofing <br />membrane for podium decks under pedestal set roof pavers and for the <br />interior waterproofing of large outdoor planters. ELASTOSEAL-5000 is <br />available in two different formulas; one for vertical applications and one <br />for horizontal applications. <br />• E LASTOSEAL-5000H (horizontal - for podium decks) <br />• E LASTOSEAL-5000V (vertical - for planters and exterior foundation wall <br />applications) <br />Typical Applications: <br />•H <br /> orizontal (above grade) Waterproofing: <br />•A <br /> pplications over elevated concrete slabs under pedestal set roof <br />pavers on balconies, terraces, sundecks, plaza decks, and above <br />grade walkways <br />• Interior bottom of concrete planters <br />•V <br /> ertical Waterproofing: <br />• Interior side walls of concrete planters <br />•B <br /> elow grade exterior foundation walls (concrete or CMU block) <br />NOTE: Contact Aquafin Technical Department for any projects, uses, <br />applications or areas not listed on this Technical Data Sheet. <br />Advantages: <br />• Available in two formulas (vertical and horizontal) for proper consistency <br />and ease of use <br />• One component, just mix with water <br />• Elastomeric, excellent flexibility with temperature changes <br />• Monolithic and seamless <br />• Meets the requirements of ASTM C836 <br />• Meets the requirements of ASTM E96 <br />• Does not contain coal tar <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Technical Properties: <br />ELASTOSEAL-5000H</p> <p>ELASTOSEAL-5000V</p> <p>Viscosity at <br />80°F (27°C):</p> <p>3500 ± 1000 cps</p> <p>30,000 ± 5000 cps</p> <p>Pot Life @ 75°F (24°C):</p> <p>~20 min</p> <p>~20 min</p> <p>Total Solids by Weight, <br />(ASTM D2369):</p> <p>96 ± 3%</p> <p>96 ± 3%</p> <p>Total Solids by Volume, <br />(ASTM D2697):</p> <p>85 ± 3%</p> <p>85 ± 3%</p> <p>Specific Gravity:</p> <p>1.20 ± 0.3</p> <p>1.19 ± 0.1</p> <p>Hardness, (ASTM <br />D2240, Shore A):</p> <p>30 ± 5</p> <p>30 ± 5</p> <p>Tensile Strength, <br />(ASTM D412):</p> <p>350 ± 50 psi <br />2.41 ± 0.3 MPa</p> <p>350 ± 50 psi <br />2.41 ± 0.3 MPa</p> <p>Tear Resistance, Die C, <br />(ASTM D624):</p> <p>80 ± 15 pli <br />14 ± 2.6 kN/m</p> <p>100 ± 15 pli <br />17.5 ± 2.6 kN/m</p> <p>Ultimate Elongation, <br />(ASTM D412):</p> <p>550 ± 50%</p> <p>550 ± 50%</p> <p>Service Temperature:</p> <p>-25°F to 150°F <br />-31.7°C to 65°C</p> <p>-25°F to 150°F <br />-31.7°C to 65°C</p> <p>Color:</p> <p>Black</p> <p>Black</p> <p>VOCs <br />(ASTM D-2369):</p> <p><0.42 lb/gal, <br /><50 gm/liter</p> <p><0.42 lb/gal, <br /><50 gm/liter</p> <p>All data are averages of several tests under laboratory conditions. In practice <br />climatic variations such as temperature, humidity, and porosity of substrate may <br />affect these values.</p> <p>Substrate Preparation: <br />• All concrete substrates must be strong, solid, stable, and of load bearing <br />capacity. <br />• Areas designated to receive repairs must remain structurally sound <br />and stable during demolition and surface preparation work, and these <br />conditions must continue throughout the course of the repair work. Any <br />areas of concern or uncertainty should be discussed immediately with <br />the site Superintendent and brought to the attention of the Engineer of <br />record. <br />• Concrete and CMU block substrates must be clean and free from all <br />potential bond breakers such as loose sand, dirt, dust, efflorescence <br />and mineral deposits, cement laitance, grease, oil, previous coatings, <br />paint, sealers, water repellants, curing compounds, form release agents, <br />etc. Mechanically clean the substrate to remove any bond-inhibiting <br />substances and/or contaminants that could interfere with adhesion. <br />• Concrete must be a minimum 5 days old or have reached a minimum <br />2,500 psi (17 MPa) compressive strength, to be treated with <br />ELASTOSEAL-5000. <br />Page 1 of 4 <br />(05/20/25-EK,VB,AC)</p> <p>ELASTOSEAL-5000 <br />• On elevated concrete decks, all drains must be unclogged and working <br />properly. <br />• For best results, all exterior horizontal surfaces should be sloped <br />according to industry standards to facilitate water removal. All water <br />should drain and/or evaporate within 48 hours. <br />• All concrete and CMU block surfaces should be free from voids, bug <br />holes, honey combs, ridges, or low spots that are more than 1/4” (6 <br />mm) in depth. <br />• E LASTOSEAL-5000 can be applied up to 1/4“ (6mm) thick to correct <br />minor low spots and to increase slope in order to facilitate water <br />removal in small areas [up to 4 ft2 (0.37 m2)]. <br />• CMU (concrete masonry unit) block walls must be at least 10 days old <br />to be treated with ELASTOSEAL-5000. <br />• Repair any loose CMU block units. <br />• Following repairs, all concrete must be mechanically prepared to a <br />concrete surface profile (CSP) 3 – 4 per the International Concrete <br />Repair Institute (ICRI) Guideline No. 310-2R-2013. Steel shot blasting, <br />and hydro blasting (high pressure water-blasting at > 5,000 psi) are the <br />preferred methods. Acid etching is not allowed, broom finish on new <br />concrete as a substitute for mechanical preparation is not acceptable. <br />Burn off any reinforcing fibers and vacuum remains. <br />• After mechanical preparation, check the porosity of the concrete surface <br />using the water drop test method (ASTM F3191). Beading water drops <br />signal a non-absorptive condition. Additional profiling will be necessary <br />until the water drop test verifies an absorptive, porous concrete surface. <br />If additional profiling does not remedy the non-absorptive condition, <br />contact Aquafin Technical Department. <br />• After mechanical preparation, perform job site mock-ups and bond tests <br />(peel and adhesion tests) prior to the application of ELASTOSEAL-5000 <br />on concrete surfaces. <br />• If the bond test does not show satisfactory results, the use of PRO-Tekt SP <br />(Sealant Primer) or VAPORTIGHT COAT® SG2 will be required prior to <br />the application of ELASTOSEAL-5000. Refer to the current PRO-Tekt SP <br />(Sealant Primer) or VAPORTIGHT COAT® SG2 Technical Data Sheet <br />for all application instructions, including surface preparation, and other <br />important information. <br />• The surface of PRO-Tekt SP (Sealant Primer) or VAPORTIGHT COAT® <br />SG2 must be clean and dry prior to application of ELASTOSEAL-5000. <br />• If a primer is not used, all concrete (and CMU block surfaces) must be <br />clean and dry prior to the application of ELASTOSEAL-5000. <br />NOTES: It is the applicator’s responsibility to test and determine if <br />ELASTOSEAL-5000 can be applied directly over solid concrete surfaces <br />without the use of a recommended Aquafin primer. Primers are generally <br />not required over CMU block surfaces. <br />In addition to general surface preparation requirements listed above, the <br />following supplementary guidance is also provided: <br />•H <br /> orizontal Structural Concrete Repairs: <br />• Use MORTAR-40 CI, MORTAR-Screed CI, Pavemend DOTLine, or <br />Pavemend SL. <br />SL <br />•H <br /> orizontal Resurfacing, Re-Sloping, and Non-Structural Concrete <br />Repairs: <br />• Use MORTAR-QuickPatch or MORTAR-Screed CI.. <br />•V <br /> ertical Structural Concrete Repairs: <br />•U <br /> se MORTAR-40 CI (spray-apply or form & pour) <br />•V <br /> ertical Resurfacing and Non-Structural Concrete Repairs: <br />•U <br /> se MORTAR-V/O CI to repair non-leaking, static cracks, fill in <br />surface voids (bug holes), and perform repairs. <br />•C <br /> MU Block Walls: <br />•U <br /> se MORTAR-V/O CI to fill in any missing mortar in the mortar</p> <p>joints and create a flush, even surface. <br />NOTES: Refer to the current MORTAR-40 CI, MORTAR-Screed CI, <br />MORTAR-QuickPatch, MORTAR-V/O CI, Pavemend DOTLine, or <br />Pavemend SL Technical Data Sheet for application instructions, including <br />surface preparation, and other important information. <br />Plug Active Water Leaks <br />• If water is accumulating from an active leak(s) through cracks or joints in <br />masonry walls, concrete walls, or concrete floors, Aquafin recommends <br />the process of injection grouting as a first step in stopping water <br />intrusion. For more information about Aquafin’s extensive line of Injection <br />Grouts, contact your local Aquafin Representative. <br />Concrete Moisture Testing: <br />Aquafin recommends moisture testing of all concrete slabs prior to <br />application of ELASTOSEAL-5000. However, moisture testing is only a <br />guideline and can be influenced by environmental factors. <br />• E xterior Concrete Slabs: To obtain an approximate measurement of <br />the moisture in exterior concrete slabs, Aquafin recommends using a <br />combination of in-situ RH content (%) testing and surface MC (%) testing <br />and then comparing the results. <br />Mitigate Moisture Vapor <br />• If there is evidence of a moisture vapor issue(s) in existing concrete, <br />Aquafin recommends the application of a topical epoxy vapor barrier <br />prior to the application of ELASTOSEAL-5000. <br />• For more information about Aquafin’s VAPORTIGHT COAT®-SG <br />products visit: www.vaportightcoat.com or contact your local Aquafin <br />Representative. <br />Remediate Oil and Grease: <br />• Trace amounts of oil, grease, or similar substances, must be thoroughly <br />degreased using a cleaner that is appropriate for the substrate. <br />• Follow all written instructions for the cleaner and completely remove all <br />residue left from the cleaning process. <br />• If the concrete slab has the appearance of oil or grease contamination, <br />Aquafin recommends the application of a topical epoxy oil barrier <br />coating prior to the application of ELASTOSEAL-5000. <br />• For more information about Aquafin’s VAPORTIGHT COAT®-SG2 visit: <br />www.vaportightcoat.com or contact your local Aquafin Representative. <br />Cracks and Joints: <br />• Control Joints, Expansion Joints, Active (dynamic) Cracks, and Static <br />(non-moving) Cracks: <br />• Treat control joints, expansion joints, active (dynamic) cracks, and <br />static cracks according to project specifications. <br />• If a sealant is specified, as your local Aquafin Representative about <br />PRO-Tekt Caulk and PRO-Tekt Joint Sealant products. Refer to the <br />current PRO-Tekt Caulk or PRO-Tekt Joint Sealant Technical Data <br />Sheet for all application instructions, including surface preparation, <br />and other important information. <br />• Static (non-moving) Cracks up to 1/16” (1.5 mm) wide can be pretreated using ELASTOSEAL-5000: <br />•A <br /> pply a stripe coat of ELASTOSEAL-5000 at a minimum 35 - 37 <br />mils DFT (dry film thickness) over the cracks. See chart on page 4 <br />for coverage and guidance for WFT (wet film thickness). <br />• E xtend ELASTOSEAL-5000 over cracks by at least 1” on all sides. <br />•A <br /> llow to cure for at least 4 hours. <br />• Static (non-moving) Cracks from 1/16” (1.5 mm) to 1/8” (3 mm) <br />wide can be chased and repaired:</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 2 of 4 <br />(05/20/25-EK,VB,AC)</p> <p>ELASTOSEAL-5000 <br />• R out out static (non-moving) cracks to a U-shaped configuration, <br />approx. ¾” to 1” (19 mm to 25 mm) wide and approx. 1” to 2” <br />(25 mm to 51 mm) deep. <br />• R emove all dirt and debris from routed cracks with a brush or with <br />compressed air. <br />• F lush cracks clean with water. <br />• F ill prepared cracks with MORTAR-QuickPatch (horizontal cracks) <br />or MORTAR-V/O (vertical cracks). <br />Jobsite Preparation: <br />• Protect areas not to be treated from ELASTOSEAL-5000. Cured <br />ELASTOSEAL-5000 can only be removed mechanically. <br />•O <br /> nly proceed with application when ambient and surface temperatures <br />are between 50°F (10°C) to 100°F (38°C) and falling and more than <br />6°F (3°C) above the dew point. <br />• Only proceed with application when ambient humidity is minimum of <br />40% and maximum of 75%. <br />• Installation should be done in late afternoon or evening hours. <br />•D <br /> o not apply ELASTOSEAL-5000 when temperatures are expected to <br />fall below 50°F (10°C) within 48 hours after placement. <br />•D <br /> o not apply ELASTOSEAL-5000 to frozen or frost covered concrete <br />surfaces. <br />•D <br /> o not apply ELASTOSEAL-5000 if humidity is at or above 80%. <br />• Do not apply ELASTOSEAL-5000 when rain is expected within 24 hours <br />after placement [based on 75°F (24°C) and 50% relative humidity]. <br />•H <br /> ot surfaces should be cooled and shaded while cold surfaces should <br />be heated and sheltered. <br />• Do not apply ELASTOSEAL-5000 in direct sunlight. Protect mixing and <br />application area from direct sunlight and wind. Provide artificial shade <br />and wind breaks when needed. <br />Mixing: <br />• Condition material to 70°F to 80°F (21°C to 27°C) prior to mixing <br />and application. <br />• Open container and mix at slow speeds (not exceeding 500 rpm) for <br />3 minutes to evenly distribute pigments and other ingredients that may <br />have settled, until a homogeneous mixture is achieved. Thoroughly <br />scrape sides of pail as material is mixed. <br />• The ratio is 1:20 (1 part water to 20 parts ELASTOSEAL-5000). <br />• Use a scientific measuring container and accurately measure out 25.5 <br />oz. (0.75 L) of water. <br />• The temperature of the water should be approx. 75ºF (24ºC). <br />• Add the pre-measured water to the 4 gallons of ELASTOSEAL-5000 <br />contained in the unit. <br />• Mix at slow speeds (not exceeding 500 rpm) for at least 3 minutes, until <br />a homogeneous mixture is achieved. Thoroughly scrape sides of pail as <br />material is mixed. <br />• Use caution not to whip air into the material as this may result in pinhole <br />blisters and/or shortened pot life. Do not mix in an up and down motion. <br />• Apply product immediately after mixing. <br />• Once mixed with water, the working time is approx. 20 minutes based <br />on 75ºF (24ºC) and 50% RH. <br />Application: <br />Read all instructions thoroughly prior to installation. <br />• Always apply ELASTOSEAL-5000 over clean, dry surfaces. <br />• Aquafin recommends the use of a squeegee, a notched squeegee, or <br />a notched trowel for application. A brush, phenolic resin core roller, or <br />an airless sprayer can be used, but extra care should be taken to avoid <br />trapping air which may result in bubbles. <br />• F irst Coat: Apply the first coat of ELASTOSEAL-5000 in a monolithic <br />application at a maximum rate of 21 ft²/gallon (0.5 m² /Liter) to <br />achieve a minimum of 70 (± 2) mils DFT (dry film thickness) per coat. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>ELASTOSEAL-5000 must be a uniformly thick, void-free, continuous <br />membrane across the entire surface of the applicaton area. Inspect <br />the surface for damage. Any surface damage on the first coat must be <br />repaired prior to the application of the second coat. Allow to cure for at <br />least 4 hours and pay close attention to recoat times. <br />•S <br /> econd Coat (optional): Apply the second coat of ELASTOSEAL-5000 <br />within 48 hours after the first coat in a monolithic application at a <br />maximum rate of 21 ft²/gallon (0.5 m² /Liter) to achieve a minimum of <br />70 (± 2) mils DFT (dry film thickness) per coat. ELASTOSEAL-5000 must <br />be a uniformly thick, void-free, continuous membrane across the entire <br />surface of the applicaton area. Allow to cure for at least 4 hours. <br />Note: See chart on page 4 for coverage and guidance for WFT (wet film <br />thickness). <br />Curing: <br />•A <br /> llow ELASTOSEAL-5000 to cure for at least 4 hours between first and <br />second coats [based on 75°F (24°C) and 50% relative humidity]. <br />• If recoat window is missed (if more than 48 hours has passed after the <br />first coat of ELASTOSEAL-5000), it is necessary to clean the surface and <br />then follow with an application of PRO-Tekt SP (Sealant Primer) before <br />proceeding with the next coat of ELASTOSEAL-5000. <br />Notes: Curing times, working times, and drying times are approximate and <br />will vary depending on ambient (air) temperature, mix water temperature, <br />the temperature of ELASTOSEAL-5000 in the packaging, surface <br />temperature of host concrete, host concrete profile, and the application <br />thickness. High temperatures, and high humidity will shorten the curing <br />time and working time. Low temperatures and low humidity will extend the <br />curing time. <br />Protection: <br />• Keep ELASTOSEAL-5000 protected from damage by work and other <br />trades as well as from exposure to direct sunlight. <br />• Keep ELASTOSEAL-5000 covered/shaded and install protection board, <br />geotextile drainage composite, backfill, pedestal paver system, etc. as <br />soon as possible. <br />Limitations: <br />• Do not dilute or thin product under any circumstance. <br />• Do not use ELASTOSEAL-5000 in swimming pools, waterfalls for <br />swimming pools, hot tubs, fountains, and similar water features. <br />• Do not use on swimming pool decks. <br />• Do not use ELASTOSEAL-5000 in any submerged areas. Ensure that <br />there is proper drainage in all areas where ELASTOSEAL-5000 is <br />used. For water-holding/water containment applications, ask your local <br />Aquafin representative about AQUAFIN-1K and AQUAFIN-2K/M <br />products. <br />• Do not apply ELASTOSEAL-5000 over the following substrates and <br />conditions: below grade concrete floor slabs, on grade concrete floor <br />slabs, split concrete slabs with buried membranes, sandwich slabs with <br />insulation, slabs over unvented metal pans, magnesite, or lightweight <br />concrete. Contact Aquafin Technical Department with questions. <br />• Once containers have been opened, mix and use material as soon as <br />possible. <br />• ELASTOSEAL-5000 is very sensitive to heat and moisture. Consult <br />Aquafin Technical Department when mixing or placing outside of the <br />temperature recommendations listed. <br />• ELASTOSEAL-5000 is not designed to be an aesthetic product. Product <br />will fade over time. <br />• The physical properties of ELASTOSEAL-5000 are not UV stable. <br />ELASTOSEAL-5000 cannot be used in applications where it will be left <br />uncovered and exposed to direct sunlight. <br />Page 3 of 4 <br />(05/20/25-EK,VB,AC)</p> <p>ELASTOSEAL-5000 <br />• Applications on exterior foundation walls must be followed with <br />protection board and must be backfilled. <br />• ELASTOSEAL-5000 is not abrasion resistant and it cannot be used as a <br />wear surface. <br />• Projects and applications in areas not listed on this Technical Data <br />Sheet require pre-approval from Aquafin Technical Department prior <br />to application of ELASTOSEAL-5000 in order to qualify for any type of <br />warranty. Contact Aquafin Technical Department or your local Aquafin <br />Representative for assistance. <br />• E LASTOSEAL-5000 should be applied to the entire floor and/or wall <br />surface(s) in order to perform effectively. It is not designed to be applied <br />in a small limited treatment area (such as application only over joints and <br />cracks). <br />• E LASTOSEAL-5000 is not designed for use as a pedestrian traffic <br />coating or a vehicle traffic coating or as a base coat for these systems. <br />• For applications in areas that will receive foot traffic without an <br />application of pavers, contact your local Aquafin Representative about <br />Aquafin Pedestrian Traffic Coatings. <br />• For applications in areas that will receive vehicle traffic, ask your local <br />Aquafin Representative about Aquafin Vehicle Traffic Coatings. <br />• E LASTOSEAL-5000 is not a replacement for proper repairs on <br />damaged, deteriorated, or cracked concrete or masonry structures. <br />• If structural repairs are needed, consult a licensed Engineer and ask <br />an Aquafin Representative about Aquafin structural concrete repair <br />products such as MORTAR-40 CI, MORTAR-Screed CI, Pavemend <br />DOTLine, and Pavemend SL. <br />SL</p> <p>Storage: Keep containers closed, store in a cool, dry, indoor location <br />away from heat, direct sun, sparks, open flame, and moisture and <br />protect material from freezing.</p> <p>Clean-up: <br />Promptly wash hands with baby oil. Clean tools and equipment with <br />Mineral Spirits immediately after use. Cured material must be removed <br />mechanically. Soaking tools in a solvent-based cleaner will help when <br />mechanical removal is necessary.</p> <p>LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed, or implied as to any specific methods of application or use of the product. <br />We do not guarantee compatibility of Aquafin products with other brands. For this <br />reason, we strongly recommend application of a sample area at the jobsite to help <br />determine suitability with other products. AQUAFIN INC. MAKES NO WARRANTY <br />AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND <br />THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED. <br />AQUAFIN, INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. Any claim for a defective product must <br />be filed within 30 days of discovery of a problem and must be submitted with written <br />proof of purchase.</p> <p>Packaging: <br />ELASTOSEAL-5000 is available in two formulas; a formula for horizontal <br />applications, and a formula for vertical applications: <br />• E LASTOSEAL-5000-H (horizontal) <br />• 5 gal pail containing 4 gal of product (15.1 liters) <br />• E LASTOSEAL-5000-V (vertical) <br />• 5 gal pail containing 4 gal of product (15.1 liters) <br />Shelf Life & Storage: <br />Shelf Life: 12 months in unopened, original packaging when stored at <br />temperatures between 65°F and 90°F (18°C to 32°C).</p> <p>Note: <br />Proper application is the sole responsibility of the user. Applicators are <br />expected to follow ICRI and ACI guidelines as well as other applicable <br />industry standards. Aquafin personnel or representatives are not site <br />inspectors or construction project managers and therefore do not approve <br />surface preparation, mixing, or application of Aquafin products. Site visits <br />by Aquafin personnel or representatives are solely for the purpose of <br />making technical recommendations, not for providing supervision or quality <br />control. <br />General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time <br />of printing. Depending on specific applications, in particular regarding <br />substrates, processing and environmental conditions may affect final results. <br />Safety: <br />Refer to SDS. Avoid contact with skin and eyes. Wear rubber gloves and <br />safety goggles during mixing and application. After contact with skin, <br />wash with plenty of water. In case of eye contact, rinse immediately with <br />plenty of water for 15 minutes and seek medical advice. KEEP OUT OF <br />REACH OF CHILDREN.</p> <p>For Professional Use Only.</p> <p>ELASTOSEAL-5000 Coverage Rate Chart <br />No. of <br />coats</p> <p>Guidance for WFT <br />(Wet Film Thickness) <br />per coat</p> <p>Total Required DFT <br />(Dry Film Thickness)</p> <p>Coverage Rate</p> <p>Yield per Unit</p> <p>mils</p> <p>mm</p> <p>mils</p> <p>mm</p> <p>ft²/gal</p> <p>m²/L</p> <p>ft²</p> <p>m²</p> <p>Elevated Concrete Decks Under Paver <br />Systems</p> <p>1-2</p> <p>74 - 126</p> <p>1.9 - 3.2</p> <p>70 - 120</p> <p>1.8 - 3.0</p> <p>12 - 21</p> <p>0.3 - 0.5</p> <p>48 - 84</p> <p>4.5 - 7.8</p> <p>Interior Coating for Concrete Planters</p> <p>1-2</p> <p>74 - 126</p> <p>1.9 - 3.2</p> <p>70 - 120</p> <p>1.8 - 3.0</p> <p>12 - 21</p> <p>0.3 - 0.5</p> <p>48 - 84</p> <p>4.5 - 7.8</p> <p>Below Grade Exterior Foundation Walls</p> <p>1-2</p> <p>74 - 126</p> <p>1.9 - 3.2</p> <p>70 - 120</p> <p>1.8 - 3.0</p> <p>12 - 21</p> <p>0.3 - 0.5</p> <p>48 - 84</p> <p>4.5 - 7.8</p> <p>Stripe Coat</p> <p>1</p> <p>37 - 39</p> <p>0.9 - 1.0</p> <p>35 - 37</p> <p>0.8 - 0.9</p> <p>40 - 42</p> <p>0.9 - 1.0</p> <p>160 - 168</p> <p>14 - 16</p> <p>Notes: Application rates and yield values are approximate. Actual coverage may vary due to due to texture, and absorption of substrate. Failure to achieve the required DFT (dry mil thickness) <br />will compromise the effectiveness of the product and void the warranty. It is the applicator’s responsibility to verify that the required DFT has been attained.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 4 of 4 <br />(05/20/25-EK,VB,AC)</p>
