TDS-EPOXY-MV.pdf
2 Pages
149 KB
Download
<h1>TDS-EPOXY-MV.pdf</h1> <p>EPOXY-MV <br />MULTI-PURPOSE, HIGH-MODULUS, MEDIUM-VISCOSITY BONDING ADHESIVE <br />DESCRIPTION <br />EPOXY-MV is a 100% solids, two-component, high-modulus, <br />medium-viscosity, moisture-insensitive, structural epoxy <br />adhesive. <br />APPLICATIONS <br />EPOXY-MV is designed as an adhesive for bonding freshly <br />mixed concrete to hardened concrete, for bonding hardened <br />concrete to hardened concrete and other materials, and as a <br />binder for epoxy mortars. EPOXY-MV may also be used for <br />anchoring bolts or dowels and reinforcing steel in concrete. <br />ADVANTAGES <br />▪ Medium-viscosity formula works well in bulk dispensing <br />pumps for efficient application <br />▪ Moisture insensitive for use in damp environments <br />▪ High modulus <br />▪ Excellent adhesion to most materials makes for a versatile, <br />multi-purpose structural epoxy adhesive <br />COMPLIANCES <br />▪ ASTM C881 (Type I, II. Grade 2. Class B & C.) <br />▪ AASHTO M235 <br />▪ VOC compliant, 0 g/L <br />PACKAGING <br />21.2 oz cartridge <br />▫ side by side cartridge (1:1 mix ratio) <br />▫ 12 cartridges per case <br />1-gallon unit <br />▫ Component A: (1) ½-gallon can <br />▫ Component B: (1) ½-gallon can <br />2-gallon unit <br />▫ Component A: (1) 1-gallon can <br />▫ Component B: (1) 1-gallon can <br />10-gallon unit <br />▫ Component A: (1) 5-gallon pail <br />▫ Component B: (1) 5-gallon pail <br />Appearance of Components: A - Clear, B - Amber <br />Shelf Life: 2 years in original unopened container <br />Storage: 40°F to 95°F in dry and dark conditions <br />Temperature Considerations: IMPORTANT! Epoxy resins are <br />temperature sensitive and care should be taken to condition all <br />components to between 65°F to 85°F for a minimum of 24 hrs. <br />prior to mixing and placement. Temperatures colder than stated <br />range increase viscosity of resins and inhibit mixing and flow of <br />materials. Temperatures warmer than stated range decrease <br />viscosity of resins, hasten the cure and reduce the working time. <br />Mixing and curing at less than ideal temperatures, <60°F or <br />>95°F, will require special considerations. <br />COVERAGE <br />Apply EPOXY-MV at a thickness of approximately 20 mils [80 <br />sq. ft. /gallon]. One gallon will yield 231 cubic inches.</p> <p>CURE TIME <br />Use the table below to determine minimum cure times based on <br />the temperature of the materials and the substrate. <br />Average Temperature of Materials & Substrate (°F) <br />Cure Temp</p> <p>60-64</p> <p>65-69</p> <p>70-74</p> <p>75-79</p> <p>80-84</p> <p>85+</p> <p>Cure Time</p> <p>8 hrs</p> <p>7 hrs</p> <p>6 hrs</p> <p>5 hrs</p> <p>4 hrs</p> <p>3.5 hrs</p> <p>*Set times are merely averages, site conditions will dictate actual cure response. <br />INSTALLATION <br />Surface Preparation: Surface to be bonded must be clean and <br />sound. Remove oil, dirt, grease, laitance, curing compounds and <br />other foreign matter that may cause a problem with bond. <br />Abrasive cleaning and mechanical removal methods are <br />recommended. All drilled holes must be cleaned with a <br />cylindrical bristle brush to remove all loose material. Use clean, <br />oil free, compressed air to blow out any remaining dust or debris <br />prior to installation. <br />Mixing: CARTRIDGE: Remove the protective cap from the <br />adhesive cartridge and insert the cartridge into the <br />recommended dispensing tool. Before attaching the mixing <br />nozzle, balance the cartridge by dispensing a small amount of <br />material until both components are flowing evenly. Screw the <br />provided mixing nozzle on to the cartridge (do not modify mixing <br />nozzle). Confirm that internal mixing element is in place prior to <br />dispensing adhesive. Begin squeezing a small amount of <br />material from the mixing nozzle onto a disposable surface until <br />the material extruded is a smooth uniform color with no streaks. <br />Material with an off color or streaking is not properly mixed and <br />will not set properly or perform as expected. Do not use this part <br />for installation. Once the proper mixture is achieved, discard the <br />material that was initially extruded from the nozzle per federal, <br />state, and local regulations, then begin installation. BULK: Mix <br />equal volumes of Component A and Component B for 3 minutes <br />with a low speed drill (300 rpm), jiffy mixer, or paddle. Mix only <br />what can be used during the pot life. <br />Placement: As a structural adhesive and for bonding fresh <br />concrete to hardened concrete, apply the EPOXY-MV material <br />neat by brush, roller or spray and work into substrate. While <br />EPOXY-MV is still tacky, place the fresh concrete. <br />For anchoring dowels, bolts, reinforcing steel, etc., the depth of <br />the hole should be approximately 9 to15 times the bolt diameter. <br />The space (annulus) around the bolt in the hole should not <br />exceed 1/8”. Always dispense the EPOXY-MV into the <br />anchoring hole filling from the bottom up. Insert the bolt, dowel <br />or anchor turning slowly during insertion. After insertion, the hole <br />should be completely full of epoxy. <br />To produce a mortar for patching repairs, mix 1 to 4-1/2 parts by <br />volume clean, dry, well graded silica sand to 1 part by volume of <br />mixed EPOXY-MV. Mix thoroughly until all of the sand is wet and <br />evenly dispersed. First, apply a prime coat over the area to be <br />repaired with the neat EPOXY-MV. Place the mortar, working it <br />well into the surface of the concrete before the prime coat <br />becomes tack free. Lifts should not exceed 1” in thickness.</p> <p>05/05/2020</p> <p>1 <br />AQUAFIN Inc. | 505 Blue Ball Rd. #160 | Elkton, MD 21921 | Phone: 410-392-2300 | Fax: 410-392-2324 <br />www.aquafin.net</p> <p>EPOXY-MV <br />MULTI-PURPOSE, HIGH-MODULUS, MEDIUM-VISCOSITY BONDING ADHESIVE <br />LIMITATIONS <br />▪ For professional use only <br />▪ Always test a small amount of EPOXY-MV to ensure that the <br />product is mixed properly and thoroughly and that the material <br />will harden properly before proceeding with the installation. <br />▪ If the EPOXY-MV is no longer tacky during bonding <br />operations, and within 16 hours after application of the <br />bonder, clean and solvent wipe the area and re-apply the <br />EPOXY-MV epoxy. <br />▪ If more than 16 hours has lapsed since application, the area <br />must be lightly sanded or abraded and solvent wiped clean <br />prior to re-application of the EPOXY-MV. <br />▪ Consult AQUAFIN representative when mixing or placing <br />outside of the temperature recommendations listed.</p> <p>FIRST AID <br />EYE CONTACT: Flush immediately with water for at least 15 <br />minutes. Contact physician immediately. <br />RESPIRATORY CONTACT: Remove person to fresh air. <br />SKIN CONTACT: Remove any contaminated clothing. <br />Remove epoxy immediately with a dry cloth or paper towel. <br />Solvents should not be used as they carry the irritant into the <br />skin. Wash skin thoroughly with soap and water. <br />IF INGESTED: Do not induce vomiting. If swallowed give water <br />to drink. Seek medical treatment immediately. <br />GENERAL: <br />Remove <br />contaminated <br />soaked <br />clothing <br />immediately. In the event of persistent symptoms receive <br />medical treatment. <br />CURED EPOXY RESINS ARE INNOCUOUS.</p> <p>CLEAN UP <br />EQUIPMENT: Uncured material can be removed with CClean100 or approved solvent. Cured material can only be <br />removed mechanically. <br />MATERIAL: Collect with absorbent material. Flush area with <br />water. Dispose of in accordance with local, state and federal <br />disposal regulations.</p> <p>WARRANTY <br />This product is warranted and guaranteed to be of good quality. <br />Manufacturer, as its sole and exclusive liability hereunder, will <br />replace material if proved defective. This warranty and <br />guarantee are expressly in lieu of all others, express or implied, <br />including any implied warranty of merchantability or fitness for a <br />particular purpose and may not be extended by representatives <br />or any persons, written sales information, or drawing in any <br />manner whatsoever. While the manufacturer recommends uses <br />for the product based on tests believed reliable, no warranties, <br />express or implied, or guarantees can be given as to particular <br />methods of use or application, nor can performance be <br />warranted, expressly or impliedly, or guaranteed under special <br />conditions. <br />Distributors, <br />salespersons <br />or <br />company <br />representatives are not authorized to extend or vary any <br />warranties or guarantees beyond those outlined herein, nor may <br />the manufacturer’s or seller’s limitation of liability be waived or <br />altered in any manner whatsoever.</p> <p>CAUTIONS <br />READ SDS PRIOR TO USING PRODUCT! <br />▪ Component A: Irritant <br />▪ Component B: Corrosive <br />▪ Product is a strong sensitizer. Use of safety goggles and <br />chemical resistant gloves are recommended. <br />▪ Use in a well-ventilated area and avoid breathing vapors <br />▪ Use of a NIOSH/MSHA organic vapor respirator is <br />recommended if ventilation is inadequate. <br />▪ Avoid skin contact <br />▪ Do not take internally <br />▪ Keep out of reach of children</p> <p>05/05/2020</p> <p>2 <br />AQUAFIN Inc. | 505 Blue Ball Rd. #160 | Elkton, MD 21921 | Phone: 410-392-2300 | Fax: 410-392-2324 <br />www.aquafin.net</p>
