505 Blue Ball Rd. #160
Elkton, MD 21921
Two-Component, Solvent-Free, Low Viscosity, Epoxy Resin
CSI Div. 03 + 07
03 64 00 Injection Grouting
07 18 00 Traffic Coatings
EPOXY-SLV is a two-component, very low viscosity, structural epoxy
adhesive for low temperature injection grouting.
• Crack repair in concrete and masonry
• Cures to form a super tough, strong bond
• Bonds effectively to damp concrete and masonry
• Fills narrow cracks as small as 2 mils wide
• Zero VOC’s
• ASTM C881 (Type IV, Grade 1, Class B and Class C)
• AASHTO M235 (Type IV, Grade 1, Class B and Class C)
• All surfaces must be free from loose sand, dirt, dust, oil, grease, and
other foreign substances that could interfere with adhesion.
• Flush cracks clean using an appropriate cleaning solution and rinse well.
Cracks may be dry or damp, but must be free of standing water.
• Use clean, oil free, compressed air to blow out any remaining dust or
debris prior to installation.
• CARTRIDGE: Remove the protective cap from the adhesive cartridge
and insert the cartridge into the recommended dispensing tool. Before
attaching the mixing nozzle, balance the cartridge by dispensing a small
amount of material until both components are flowing evenly. Attach the
provided flow restrictor, screw the provided static mixing nozzle on to
the cartridge (do not modify mixing nozzle). Confirm that internal mixing
element is in place prior to dispensing adhesive. Begin squeezing a
small amount of material from the static mixing nozzle onto a disposable
surface until the material extruded is a smooth uniform color with no
streaks. Material with an off color or streaking is not properly mixed and
will not set properly or perform as expected. Do not use this part for
installation. Once the proper mixture is achieved, discard the material
that was initially extruded from the nozzle per federal, state, and local
regulations, then begin installation.
• BULK: The volume mixing ratio is 2 Part-A to 1 Part-B (2A:1B). Combine
components A and B and mix for 3 minutes with a low speed drill (300
rpm), jiffy mixer, or paddle. Mix only what can be used during the pot
Check our website for the latest version of the Technical Datasheet.
Physical and Technical Data
Gel Time, (ASTM D2471)
Cure Time @ 73°F (± 4°F)
Viscosity, (ASTM D2393)
Compressive Yield Strength,
Bond Strength (ASTM C882)
2 day cure
14 day cure
Elongation at Break
All data are averages of several tests under laboratory conditions. In practice
climatic variations such as temperature, humidity, and porosity of substrate may
affect these values
• First prepare the surfaces adjacent to the cracks to expose clean,
sound concrete. The injection ports should be spaced from 8” to 36”
apart, depending on the crack width and the thickness of the member
to be injected. Next, the crack should be sealed at the surface with
EPOXY-GEL at a paste width of 1.5” on each side of the crack. After
the EPOXY-GEL has cured, inject EPOXY-SLV epoxy with pressurized
dispensing equipment or use the EPOXY-SLV cartridges. EPOXY-SLV
cartridges are only designed for small repair projects with cracks at
least 1/16” in width or larger. For large projects and/or crack widths
less than 1/16”, use EPOXY-SLV bulk units with automated dispensing
equipment. Please contact Aquafin Technical Department for additional
guidance and procedures.
Page 1 of 2
Binding Mortar and Grout for Patching
• Premix entire unit of A and B or exact portions, 2 parts A to 1 part B
by volume, with low speed (300 rpm) Jiffy mixer for 3 minutes. Hold
back some neat resin for priming patch. Paint concrete to be patched
with just enough neat resin to wet out the surface. Slowly add ovendried aggregate (typically 4-5 parts of aggregate to 1 part epoxy)
to the mixed epoxy while mixing with a slow speed Jiffy mixer, being
careful not to mix in air. Prepared mortar must be placed before primer
becomes tack free. Epoxy mortar may be placed and leveled with
trowels. Do not disturb patch until it is fully cured.
• Inspect and Seal underside of slab prior to filling reflective cracks. Pour
neat EPOXY-SLV into crack, continuing placement until crack is full. It may
be necessary to “V”-notch cracks to aid in placement.
EQUIPMENT: Uncured material can be removed with approved solvent.
Cured material can only be removed mechanically or by soaking in an
MATERIAL: Collect with absorbent material. Flush area with water. Dispose
of in accordance with local, state and federal disposal regulations.
• Do not thin with solvents
• Compressed air equipment must have an oil/air separator.
• Minimum age of concrete must be 28 days before applying.
• Always test a small amount to ensure that the product is mixed properly
and that the material will harden properly before proceeding with the
• Do not inject cracks wider than ¼” without contacting Aquafin.
• Surface temperatures must be 35°F or above.
• Do not use in temperatures above 90°F.
• Do not expose stored or uncured product to cold or freezing
temperatures below 35°F for any length of time.
• Consult Aquafin Technical Department when mixing or placing outside
of the temperature recommendations listed.
Storage and Shelf Life:
Shelf Life: 2 years in original unopened container
Storage: 60°F to 90°F in dry and dark conditions
Temperature Considerations: IMPORTANT! Epoxy resins are temperature
sensitive and care should be taken to condition all components to between
60°F to 80°F for a minimum of 24 hrs. prior to mixing and placement.
Temperatures colder than stated range increase viscosity of resins and
inhibit mixing and flow of materials. Temperatures warmer than stated
range decrease viscosity of resins, hasten the cure and reduce the working
time. Mixing and curing at less than ideal temperatures, <40°F or >90°F,
will require special considerations.
Refer to SDS. For commercial use only. Avoid contact with skin and eyes.
Wear rubber gloves and safety goggles during mixing and application.
After contact with skin, wash with plenty of water. In case of eye contact,
rinse immediately with plenty of water for 15 minutes and seek medical
advice. KEEP OUT OF REACH OF CHILDREN.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year
from the date of installation to be manufactured free of defects and to be consistent
with its technical properties as stated in our current Technical Data Sheet. This product
must be used as directed and within its stated shelf life. AQUAFIN INC. will replace
or at our discretion refund the purchase price of any product, excluding cost of
labor, which is proven to be defective. Our product recommendations are based
on industry standards and testing procedures. It is the buyer’s obligation to test the
suitability of the product for an intended use prior to using it. We assume no warranties
written, expressed or implied as to any specific methods of application or use of the
product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable
for damages of any sort including remote or consequential damages, down time, or
delay. Any claim for a defective product must be filed within 30 days of discovery of a
problem, and must be submitted with written proof of purchase.
For Professional Use Only.
Proper application is the responsibility of the user. Field visits by AQUAFIN
personnel are for the purpose of making technical recommendations and
not for supervising or providing quality control on-site.
• 16 oz. cartridge (473 ml)
side by side cartridge (2:1 mix ratio)
10 cartridges per case
• 3-gallon unit (11.35 L)
Component A: (2) 1-gallon can
Component B: (1) 1-gallon can
• 15-gallon unit (56.78 L)
Component A: (2) 5-gallon pail
Component B: (1) 5-gallon pail
Page 2 of 2