505 Blue Ball Rd. #160
Elkton, MD 21921
Low-viscosity, low surface tension, 100% solids epoxy
EPOXY100-SEAL is a highly penetrating, two-component epoxy
healer/sealer. Its rapid cure time allows traffic to re-open in less than six
EPOXY100-SEAL is designed to prolong the life of concrete by sealing
cracks against moisture and chloride ion intrusion. Specific applications
▫ Bridge decks
▫ Parking decks
▫ Concrete floors
▫ Airport runways & taxiways
▫ Columns & beams in splash zones
▫ Consolidation of porous & dusting surfaces
▫ Primer or pre-treatment for subsequent epoxy or urethane deck
• Excellent bond strength
• Moisture insensitive
• High early strength
• Easy to mix - 2:1 ratio
• 100% solids
• Low viscosity
• High tensile strength providing for superior retention of aggregates
• Low odor
• Designed for automated pump or hand mix application
• ASTM C881 (Type III. Grade 1. Class B & C.)
• VOC compliant, 0 g/L
• Made in America
• 3-gallon unit
Component A: (2) 1-gallon cans
Component B: (1) 1-gallon can
• 15-gallon unit
Component A: (2) 5-gallon pails
Component B: (1) 5-gallon pail
• 165-gallon unit
Component A: (2) 55-gallon drums
Component B: (1) 55-gallon drum
Check our website for the latest version of the Technical Datasheet
• 750-gallon unit
Component A: (2) 250-gallon totes
Component B: (1) 250-gallon tote
Physical and Technical Data
C-881 Gel Time
C-884 Thermal Compatibility
D-2240 Shore D Hardness
C-882 Bond Strength (2 day cure)
C-882 Bond Strength (14 day cure)
D-695 Compressive Modulus
C-695 Compressive Strength
D-2566 Linear Coefficient of Shrinkage 0.0021
D-638 Tensile Strength
D-638 Tensile Elongation
D-790 Flexural Strength
ACI 503R Adhesion to Concrete
>500 psi (concrete failure)
Clean surface by shot-blasting or sandblasting to remove all contaminants
and open surface and cracks. Remove dust and debris by blowing off with
oil-free compressed air.
Minimum Coverage Rates
1 gallon/60-80 sq. ft.
4-8 lbs./sq. yd.
1 gallon/100-150 sq. ft.
Use the table below to determine minimum cure times based on the
temperature of the materials and the substrate.
Average Temperature of Materials & Substrate (°F)
*Set times are merely averages, site conditions will dictate actual cure response.
Page 1 of 2
Mechanically mix Component A with Component B 2:1 by volume with Jiffy
type mixer and low-speed variable drill at 300 rpm for a minimum of 3
minutes. Mix only the quantity that can be used within its gel time. BULK:
For bulk mixing, a positive displacement pump, incorporating a static mixing
wand and meter, is recommended.
Apply neat EPOXY100-SEAL by pouring or spraying on the surface.
Distribute material evenly with a squeegee, roller or broom, maintaining a
liquid head over cracks until refusal. Remove all excess material with
squeegee or broom. Broadcast select aggregate to properly cover liquid
resin. The aggregate should be moisture free and free of dirt, clay, etc. After
initial cure of first course, remove excess aggregate.
When used as primer or pre-treatment prior to overlay, consult AQUAFIN
• For professional use only
• Do not thin with solvents
• Compressed air equipment must have an oil/air separator.
• Minimum age of concrete must be 28 days before applying as an
• Substrate temperatures must be 50°F and rising prior to installation;
50°F must be maintained minimum of 10 hours post installation or meet
curing guidelines stated above for proper cure.
• Maximum of one flood coat application
• EPOXY100-SEAL is a vapor barrier after curing.
• Consult AQUAFIN representative when mixing or placing outside of the
temperature recommendations listed.
EQUIPMENT: Uncured material can be removed with approved solvent.
Cured material can only be removed mechanically.
MATERIAL: Collect with absorbent material. Flush area with water. Dispose
of in accordance with local, state and federal disposal regulations.
Storage and Shelf Life:
Shelf Life: 2 years in original unopened container
Storage: 50°F to 95°F in dry and dark conditions
Temperature Considerations: IMPORTANT! Epoxy resins are temperature
sensitive and care should be taken to condition all components to between
60°F to 85°F for a minimum of 24 hrs. prior to mixing and placement.
Temperatures colder than stated range increase viscosity of resins and
inhibit mixing and flow of materials. Temperatures warmer than stated
range decrease viscosity of resins, hasten the cure and reduce the working
time. Mixing and curing at less than ideal temperatures, <60°F or >95°F,
will require special considerations.
READ SDS PRIOR TO USING PRODUCT!
• Component A: Irritant
• Component B: Corrosive
• Product is a strong sensitizer.
• Use of safety goggles and chemical resistant gloves are recommended.
• Use in a well-ventilated area and avoid breathing vapors
• Use of a NIOSH/MSHA organic vapor respirator is recommended if
ventilation is inadequate.
• Avoid overspray or mist conditions when applied by sprayer.
• Avoid skin contact
EYE CONTACT: Flush immediately with water for at least 15 minutes.
Contact physician immediately.
RESPIRATORY CONTACT: Remove person to fresh air.
SKIN CONTACT: Remove any contaminated clothing.
Remove epoxy immediately with a dry cloth or paper towel. Solvents should
not be used as they carry the irritant into the skin. Wash skin thoroughly with
soap and water.
IF INGESTED: Do not induce vomiting. If swallowed give water to drink.
Seek medical treatment immediately.
GENERAL: Remove contaminated soaked clothing immediately. In the event
of persistent symptoms receive medical treatment.
CURED EPOXY RESINS ARE INNOCUOUS.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one
year from the date of installation to be manufactured free of defects and to be
consistent with its technical properties as stated in our current Technical Data Sheet.
This product must be used as directed and within its stated shelf life. AQUAFIN INC.
will replace or at our discretion refund the purchase price of any product, excluding
cost of labor, which is proven to be defective. Our product recommendations are
based on industry standards and testing procedures. It is the buyer’s obligation to test
the suitability of the product for an intended use prior to using it. We assume no
warranties written, expressed or implied as to any specific methods of application or
use of the product. AQUAFIN INC. MAKES NO WARRANTY AS TO
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED.
AQUAFIN, INC. shall not be liable for damages of any sort including remote or
consequential damages, down time, or delay. Any claim for a defective product must
be filed within 30 days of discovery of a problem, and must be submitted with written
proof of purchase.
For Professional Use Only.
Page 2 of 2