TDS-Fix 10-S_051619.pdf
2 Pages
37 KB
Download
<h1>TDS-Fix 10-S_051619.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>FIX 10-S</p> <p>Ultra Fast-setting Cementitious Water Stop <br />CSI Div. 03 <br />03 01 00 Maintenance of Concrete</p> <p>Technical Properties: <br />Physical state</p> <p>Powder</p> <p>LEED Points</p> <p>Color</p> <p>Gray</p> <p>Bulk density</p> <p>~75 lbs/ft3 Bulk (1.22 kg/L)</p> <p>pH - Value</p> <p>11 - 13.5</p> <p>Compressive Strength: <br />ASTM C-109</p> <p>1100 psi (8 MPa) at 1 hr <br />4000 psi (32 MPa) at 24 hr <br />10000 psi (70 MPa) at 7 d <br />10800 psi (75 MPa) at 28 d</p> <p>Flexural Strength:</p> <p>250 psi (1.8 MPa) at 1 hr <br />580 psi (4 MPa) at 24 hr <br />870 psi (6 MPa) at 1 d <br />940 psi (6.5 MPa) at 28 d</p> <p>MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />FIX 10-S is an ultra fast setting, chloride free hydraulic cement which sets <br />immediately when exposed to water. <br />Typical Applications: <br />Applied to concrete, masonry, stone, positive or negative water pressure <br />side, to: <br />• Plug/stop active water leaks <br />• Dry out wet areas <br />• Seal leaky joints, cracks or formtie holes <br />Advantages: <br />• Stops water leaks in less than 30 seconds <br />• Easy application - no mixing needed in most cases <br />• Waterproof <br />• Durable <br />• No odor - no fumes <br />Substrate Preparation: <br />The substrate must be sound, clean, and free from any surface <br />contamination. Remove any soft, deteriorated, unsound substrate, leaving <br />an appropriate opening for the FIX 10-S. Rout out cracks to a U-shaped <br />profile. Do not apply to substrates below 40°F (5°C). <br />Mixing: <br />Note: In most cases FIX 10-S can be applied as dry powder without <br />mixing. Where mixing is desired carry out as follows: <br />• Mix with clean water to obtain desired consistency. <br />• Setting time is dependent on the amount of mixing water used and the <br />temperature of the water. <br />• Warm temperatures accelerate the set, cold temperatures retard it. <br />• Mix only small quantities of material at a time.</p> <p>Physical Properties: The values stated are applicable with ambient temperatures of +23° C and 50% relative air humidity. Higher temperatures shorten <br />the processing time, lower temperatures extend processing times. <br />Storage/Shelf Life/Packaging <br />Cool and dry, 12 months in original sealed <br />packaging</p> <p>13 lb pails (5.8 kg)</p> <p>Approximate Yield: 1 lb. (0.45 kg) will fill a cavity of approx. 1” x <br />1” x 24” (25 mm x 25 mm x 600 mm). <br />Application: <br />Read all instructions thoroughly prior to installation. <br />• Dry Method: <br />For most leaking areas, firmly press FIX 10-S powder against the <br />active leak, and rub until the water stops. For large areas of moisture <br />penetration, rub FIX 10-S powder into wet surface area. <br />• Mixed Method: <br />When desired, mix an appropriate amount of material as described <br />above. Place FIX 10-S firmly into the crack or hole using gloved hand or <br />a brick jointer. Hold firmly in place until material has set, approx. 10 - 30 <br />seconds. Strike off flush with surface. <br />Clean-up <br />Promptly wash hands and tools with water before material <br />hardens. Cured material must be removed mechanically. <br />Note: <br />Installer is responsible for proper product application. Site visits by Aquafin <br />personnel or representatives are solely for the purpose of making technical <br />recommendations, not for providing supervision or quality control.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Page 1 of 2 <br />(updated 05/16/19-SM,BE)</p> <p>FIX 10-S <br />Safety: <br />Refer to SDS. This product contains portland cement and sand <br />(crystalline silica) and is highly alkaline (irritant) in contact with water. Avoid <br />breathing dust. May cause delayed lung injury (silicosis). Use rubber <br />gloves and goggles during mixing and application. Protect skin and eyes. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of cool water and seek medical advice. <br />KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a <br />period of one year from the date of installation to be manufactured free <br />of defects and to be consistent with its technical properties as stated in our <br />current Technical Data Sheet. This product must be used as directed and <br />within its stated shelf life. AQUAFIN INC. will replace or at our discretion <br />refund the purchase price of any product, excluding cost of labor, which <br />is proven to be defective. Our product recommendations are based on <br />industry standards and testing procedures. It is the buyer’s obligation to <br />test the suitability of the product for an intended use prior to using it. We <br />assume no warranties written, expressed or implied as to any specific <br />methods of application or use of the product. AQUAFIN INC. MAKES <br />NO WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A <br />PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER <br />WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down <br />time, or delay. Any claim for a defectiveproduct must be filed within 30 <br />days of discovery of a problem, and must be submitted with written proof of <br />purchase. <br />For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(updated 05/16/19-SM,BE)</p>
