_TDS-InjectPro-61 092718.pdf
2 Pages
29 KB
Download
<h1>_TDS-InjectPro-61 092718.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectPro-61</p> <p>Hydrophobic, polyurethane grout for use in potable water applications <br />CSI Div. 03 <br />03 64 00 Injection Grouting</p> <p>Physical Properties</p> <p>Product Description: <br />InjectPro-61 is a low viscosity, hydrophobic polyurethane injection grout <br />designed for sealing leaking cracks or joints where some movement is <br />possible. The system is comprised of an “A” component (base resin) and a <br />“B” component (accelerator). The “B” component is used by the applicator <br />to adjust the set times for various job site specific conditions.</p> <p>Color</p> <p>The closed cell foam created by reaction with small amounts of water will <br />maintain its physical form and not be subject to shrinkage due to wet/ <br />dry cycles. The foam will be tough, flexible and resistant to corrosive <br />environments. <br />Typical Applications: <br />Any concrete structure with water leaks requiring NSF/ANSI 61 approved <br />materials such as water tanks, water treatment plants, dams, etc. <br />Advantages: <br />• NSF/ANSI 61 Standard certified and listed by UL <br />• 100% solids, non-flammable <br />• Pumped as a single component <br />• Hydrophobic - can be used in wet and dry environments <br />• Can expand more than 30 times initial volume <br />• Adjustable reaction times <br />• Zero VOC’s, non-hazardous shipping, non-toxic permanent seal <br />Reaction Times & Use of Accelerator: <br />The reaction time can be adjusted by the addition of accelerator “B” <br />into the base resin prior to pumping. The resulting profile is affected by <br />temperature and the amount of moisture present. <br />Typical average reaction times after contact with water: <br />Accelerator % Initial Reaction Reaction Complete <br />1.25% <br />50 seconds <br />4 minutes <br />2.5% <br />15 seconds <br />65 seconds <br />Installation Procedures: <br />Refer to the Aquafin InjectPro Grouting Guideline for full instructions. Mix <br />both the grout (component A) and accelerator (component B) before <br />combining. <br />• Pour the desired amount of InjectPro-61 component A into a clean pail. <br />• Measure the appropriate amount of accelerator component B and <br />pour into the InjectPro-61, stiring until adequately mixed. Never use <br />more accelerator than recommended. Excess accelerator will cause <br />significant expansion that is prone to shrinkage. <br />During injection, the grout will follow the path of least resistance. When <br />the material has stopped penetrating it will continue to expand against the <br />confines of the crack/joint and compress within itself, forming a very dense, <br />closed cell material stopping the leak.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Liquid (un-cured) <br />Viscosity (ASTM D-1638) <br />Specific Gravity (ASTM D-1475) <br />Flash Point (ASTM D-92) <br />Solid (cured) <br />Water Absorption (ASTM D-2842) <br />Elongation (ASTM D-3574) <br />Tensile Strength (ASTM D-3574) <br />Toxicity</p> <p>InjectPro-61 Resin</p> <p>Accelerator</p> <p>Amber</p> <p>Yellow</p> <p>500 ± 100 cps</p> <p>30 ±5 cps</p> <p>1.1</p> <p>0.95</p> <p>>250°F</p> <p>220°F</p> <p>InjectPro-61 Resin <br /><1% <br />60% <br />23 psi <br />non-toxic</p> <p>Packaging: <br />InjectPro-61 Resin: <br />5 gallon pails <br />InjectPro Accelerator: <br />1 pint (16 oz.) containers <br />Storage & Shelf Life: <br />12 months when stored properly. Product is highly moisture sensitive. <br />Store in original sealed containers at temperature between 60°F – <br />90°F. Opened containers must be handled properly to prevent moisture <br />contamination. <br />Limitations: <br />• Temperature significantly affects viscosity. Protect material from <br />excessive heating and cooling prior to grouting to avoid affecting <br />viscosity. <br />• If using water baths to cool or heat pails avoid splashes to prevent <br />water coming in direct contact with resin - this will activate the reaction. <br />Do not warm above 90°F. <br />• Do not reseal containers of contaminated materials as it can create <br />pressure. <br />• Clean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material <br />such as clay or vermiculite and transfer to metal waste containers. <br />Wash area with decontamination solution (5-10% solution of sodium <br />carbonate). Dispose of waste in accordance with federal, state and <br />local regulations. <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site.</p> <p>Page 1 of 2</p> <p>(updated 09/27/18-EK)</p> <p>InjectPro-61 <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>NSF/ANSI Standard 61 Drinking Water System <br />Components File: MH61154 Control: 3L39 <br />Maximum Surface Area to Volume ratio 15cm²/L</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(updated 09/27/18-EK)</p>
