IDENTITY: InjectPro-PM3811-FAST (COMPONENT-A–Liquid Resin) Date prepared: Date revised:
SAFETY DATA SHEET SDS No M1.1.2.A
JULY 2014 JANUARY 2019
SDS No. IM.1.1.2.A
Section 1 – Product Identification IDENTITY:
Product Name:
Chemical Characterization: Product Use Description:
InjectPro-PM3811-FAST (SDS 1 of 3) Component – A (Liquid Resin)
Aqueous preparation on basis of a specific acrylate and methacrylate Injection resin
AQUAFIN, INC. 505 BLUE BALL RD. #160 ELKTON, MD 21921
24 hr Emergency Phone: Chem-Tel (800) 255-3924 Information Phone No.
(410) 392-2300
www.aquafin.net info@aquafin.net
Section 2 – Hazards Identification GHS Classification: Skin irritation, Category 2 Skin sensitization, Category 1 Eye irritation, Category 2A
H315: Causes skin irritation. H317: May cause an allergic skin reaction. H319: Causes serious eye irritation.
GHS Label element: Hazard Pictograms GHS07 Signal Word:
Warning
Hazard Statements: H301: H315: H319:
Toxic if swallowed. Causes skin irritation. Causes serious eye irritation.
Precautionary Statements: Prevention: P102: Keep out of reach of children. P261: Avoid breathing dust/fume/gas/mist/vapours/spray. P264: Wash skin thoroughly after handling. P270: Do not eat, drink or smoke when using this product. P280: Wear protective gloves/protective clothing/eye protection/face protection. Response: P301 + P315: P330: P302 + P352: P332 + P313: P362: P304 + P340: P305 + P351 + P338: P337 + P313
IF SWALLOWED: Get immediate medical advice/attention. Rinse mouth. IF ON SKIN: Wash with plenty of soap and water. IF SKIN irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. IF eye irritation persists: Get medical advice/attention. Page 1 of 6
IDENTITY: InjectPro-PM3811-FAST (COMPONENT-A–Liquid Resin)
Storage: P403 + P410: P405:
Store in a well-ventilated place. Protect from sunlight. Store locked up.
Disposal: P501:
Dispose of contents/container to an approved waste disposal site.
Section 3 – Composition / Information on Hazardous Ingredients CAS number:
Not applicable. Solution of acrylate and methacrylate monomers and salts in water.
Note: There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
Section 4 – First Aid Measures Inhalation:
Supply fresh air and consult a physician if breathing becomes difficult.
Ingestion:
Immediately drink plenty of milk or water and get medical attention.
Skin Contact:
Rinse skin with soap and plenty of water immediately. Do not use solvents or thinners. Remove contaminated clothing and shoes. Seek medical advice. Wash clothing before reuse.
Eye Contact:
Rinse cautiously with water for at least 15 minutes, lifting upper and lower eyelids occasionally. Remove contact lenses. Obtain medical attention, preferably from an ophthalmologist.
Section 5 – Fire Fighting Measures Extinguishing Media: Unsuitable extinguishing media: Fire Fighting Procedures:
Use water spray, alcohol resistant foam, dry chemical or carbon dioxide. None. As in any fire, wear self-contained breathing apparatus pressuredemand, MSHA/NIOSH (approved or equivalent) and full protective gear. Containers can build up pressure if exposed to heat (fire). Cool with water spray. Do not scatter material with high pressure water streams.
Hazardous Decomposition Products: Carbon oxides. Unusual Fire and Explosion Hazards: Bursting and explosion of container possible due to increase of pressure when exposed to increasing heat. In case of fire, cool nearby containers with water fog.
Section 6 – Accidental Release Measures Person-related Safety Precautions:
Provide plenty of fresh air. Avoid eye and skin contact. Avoid inhalation of vapors. Wear personal protective equipment. Remove or eliminate all ignition sources. Emergency procedures are not required. Page 2 of 6
Methods for cleaning-up:
Contain and collect spillage with non-combustible, absorbent materials. I.e. sand, earth, vermiculite, diatomaceous earth, universal binders, sawdust and place in container for disposal.
Waste Disposal Method:
Dispose in accordance with local, state and federal regulations.
Ecological Information:
Do not allow product to reach ground water, bodies of water, or storm water or sewage systems.
Section 7 – Handling and Storage Handling:
Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Follow all SDS/label precautions even after the container is emptied because it may retain product residues.
Storage:
Keep container closed when not in use. Do not store in direct sunlight. Avoid UV light.
Section 8 – Exposure Controls / Personal Protection General Information:
Eye-wash bottle must be available. The product does not contain any relevant quantities of materials that have to be monitored at the workplace.
Engineering Controls:
Use adequate ventilation.
Respiratory Protection:
Use local exhaust ventilation.
Skin Protection:
Wear chemical resistant protective clothing and footwear impervious to the product if there is a potential for skin contact.
Hand Protection:
Glove(s): neoprene.
Eye Protection:
Use safety goggles or face shield.
Other Protective Equipment: A safety shower and eye wash fountain should be readily available. Work/Hygienic Practices:
Wash hands before breaks and after work, and before eating, drinking or smoking.
Section 9 – Physical and Chemical Properties Physical state: Color: Odor: Solubility in water: pH-value: Boiling point: Flash point: Flammability: o Specific Gravity (water = 1) at 20 C: o Viscosity, (kinematic) at 20 C: VOC: Auto ignition Temperature:
Liquid Light yellow or bluish pigmented. Acrylic at 20°C / 68°F miscible ±6 >100°C (>212°F) >100°C (>212°F) Non-flammable 3 1.18 -1.2 g/cm ~20 - 30 cps 0 g/L No data available Page 3 of 6
IDENTITY: InjectPro-PM3811-FAST (COMPONENT-A–Liquid Resin) Lower explosion Limit:
No data available
Upper explosion Limit:
Section 10 – Stability and Reactivity Reactivity:
No dangerous reaction known under conditions of normal use.
Hazardous Decomposition:
None if used as directed.
Chemical Stability:
Stable under normal temperatures and pressures. Keep away from heat sources. Contains the following stabilizer(s): MEHQ.
Conditions To Avoid:
Heat and light.
Hazardous Polymerization:
May occur.
Incompatibilities:
Strong oxidizing agents, alkali, acid, and free radical initiators.
Section 11 – Toxicological Information Information on toxicological effects: Acute toxicity:
Dermal: Oral: Inhalation:
OSHA, HCS 2012 Classification criteria not met. Acute toxicity, oral, Category 3. OSHA, HCS 2012 Classification criteria not met.
Skin corrosion/irritation:
Skin corrosion/irritation, category 2.
Serious eye damage/eye Irritation:
Serious eye damage/eye irritation, Category 2A.
Respiratory or skin sensitization:
OSHA, HCS 2012 Classification criteria not met.
Germ cell mutagenicity:
Carcinogenicity: IARC; NTP; OSHA: Potential health effects: Inhalation:
No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. Acute: No data available. Chronic: No data available.
Skin:
Acute: Chronic:
Causes skin irritation No data available.
Eye:
Causes serious eye irritation. No data available.
Toxic if swallowed. No data available.
Page 4 of 6
Section 12 – Ecological Information No information available Further Information on Ecology:
Do not allow to enter soil, waterways or waste water.
Section 13 – Disposal Considerations Product waste:
Must be disposed of in a manner consistent with federal, state and local regulations.
Packaging waste:
Section 14 – Transport Information Proper shipping name:
Non-Flammable Solution, NOS.
USDOT (Domestic Surface):
Not regulated
IMO (Ocean):
IATA/ICAO (Air):
TDG (Canada):
UN Number:
Not listed.
Section 15 – Regulatory Information TSCA Status:
Listed or exempt
US Federal Regulatory Information: Ingredient Acrylates and methacrylates
TSCA Yes
CERCLA RQ No
SARA 302 No
SARA 313 No
WHMIS:
All components are listed on the CEPA Domestic Substances List (DSL).
IDL:
Ingredient Disclosure List (IDL), the following components are on the list: Acrylates and methacrylates.
Section 16 – Other Information Abbreviations and acronyms: USDOT: IMDG: IATA: CAS: LC50: LD50:
United States Department of Transportation. International Maritime Code for Dangerous Goods. International Air Transport Association. Chemical Abstracts Service (Division of the American Chemical Society). Lethal concentration, 50 percent. Lethal dose, 50 percent.
Page 5 of 6
IDENTITY: InjectPro-PM3811-FAST (COMPONENT-A–Liquid Resin) SDS prepared by:
Aquafin product safety department.
DISCLAIMER: We believe the statements, technical information and recommendations contained herein are reliable, but they are given without warranty or guarantee of any kind, expressed or implied, and we assume no responsibility for any loss, damage, or expense, direct or consequential, arising out of their use. Aquafin shall not be responsible for the use of this product in a manner to infringe on any patent or any other intellectual property rights held by others. User is responsible for determining appropriate safety measures and for applying the legislation covering his own activities. We recommend that user makes tests to determine the suitability of a product for its particular purpose prior to use. END OF SDS
Page 6 of 6
(January 22, 2019)