SDS_AQUAFIN-InjectPro-PM3811 Flex-40 Component-A_Resin-Liquid_032124.pdf
6 Pages
226 KB
Download
<h1>SDS_AQUAFIN-InjectPro-PM3811 Flex-40 Component-A_Resin-Liquid_032124.pdf</h1> <p>IDENTITY: InjectPro-PM3811 Flex-40 <br />(COMPONENT-A–Liquid Resin) <br />Date prepared: <br />Date revised:</p> <p>SAFETY DATA SHEET <br />SDS No. M1.1.1.B</p> <p>MARCH 2010 <br />March 2024</p> <p>SDS No. IM.1.1.1.B</p> <p>Section 1 – Product Identification <br />IDENTITY:</p> <p>Product Name:</p> <p>InjectPro-PM3811 Flex-40 <br />Component – A (liquid resin)</p> <p>Chemical Characterization: <br />Product Use Description:</p> <p>Aqueous preparation on basis of a specific methacrylate <br />Injection resin</p> <p>AQUAFIN, INC. <br />505 BLUE BALL RD. #160 <br />ELKTON, MD 21921</p> <p>24 hr Emergency Phone: Chem-Tel</p> <p>Recommended use of the chemical and restriction on use:</p> <p>Refer to the product technical data sheet. <br />For industrial and professional users.</p> <p>Information Phone No.</p> <p>(800) 255-3924 <br />(410) 392-2300</p> <p>www.aquafin.net info@aquafin.net</p> <p>Section 2 – Hazards Identification <br />GHS Classification: <br />Skin irritation, Category 2 <br />Skin sensitization, Category 1 <br />Eye irritation, Category 2A</p> <p>H315: Causes skin irritation. <br />H317: May cause an allergic skin reaction. <br />H319: Causes serious eye irritation.</p> <p>GHS Label element: <br />Hazard Pictograms <br />GHS07 <br />Signal Word:</p> <p>Warning</p> <p>Hazard Statements: <br />H301: <br />H315: <br />H319:</p> <p>Toxic if swallowed. <br />Causes skin irritation. <br />Causes serious eye irritation.</p> <p>Precautionary Statements: <br />Prevention: <br />P102: <br />Keep out of reach of children. <br />P261: <br />Avoid breathing dust/fume/gas/mist/vapors/spray. <br />P264: <br />Wash skin thoroughly after handling. <br />P270: <br />Do not eat, drink or smoke when using this product. <br />P280: <br />Wear protective gloves/protective clothing/eye protection/face protection. <br />Response: <br />P301 + P315: <br />P330: <br />P302 + P352: <br />P332 + P313: <br />P362: <br />P304 + P340:</p> <p>IF SWALLOWED: Get immediate medical advice/attention. <br />Rinse mouth. <br />IF ON SKIN: <br />Wash with plenty of soap and water. <br />IF SKIN irritation occurs: Get medical advice/attention. <br />Take off contaminated clothing and wash before reuse. <br />IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable <br />Page 1 of 6</p> <p>IDENTITY: IDENTITY: InjectPro-PM3811 Flex-40 <br />(COMPONENT-A–Liquid Resin)</p> <p>P305 + P351 + P338:</p> <p>IF IN EYES:</p> <p>P337 + P313</p> <p>SAFETY DATA SHEET <br />SDS No. M1.1.1.B</p> <p>for breathing. <br />Rinse cautiously with water for several minutes. Remove contact <br />lenses, if present and easy to do. Continue rinsing. <br />IF eye irritation persists, get medical advice/attention.</p> <p>Storage: <br />P403 + P410: <br />P405:</p> <p>Store in a well-ventilated place. Protect from sunlight. <br />Store locked up.</p> <p>Disposal: <br />P501:</p> <p>Dispose of contents/container to an approved waste disposal site.</p> <p>Section 3 – Composition / Information on Hazardous Ingredients <br />Components <br />CAS No. <br />OSHA PEL <br />ACGIH TLV <br />Percent <br />2-hydroxyethyl methacrylate <br />868-77-9 <br />< 50 <br />proprietary acrylate <br />TS <br />TS <br />dihydrogen oxide <br />7732-18-5 <br />> 50 <br />Note: There are no additional ingredients present which, within the current knowledge of the supplier and in the <br />concentrations applicable, are classified as hazardous to health or the environment and hence require reporting <br />in this section.</p> <p>Section 4 – First Aid Measures <br />Inhalation:</p> <p>Supply fresh air and consult a physician if breathing becomes difficult.</p> <p>Ingestion:</p> <p>Immediately drink plenty of milk or water and get medical attention. Only induce <br />vomiting if directed by a physician. Never give anything by mouth to an unconscious <br />person.</p> <p>Skin Contact:</p> <p>Rinse skin with soap and plenty of water immediately. Do not use solvents or thinners. <br />Remove contaminated clothing and shoes. Seek medical advice. Wash clothing before <br />reuse.</p> <p>Eye Contact:</p> <p>Rinse cautiously with water for at least 15 minutes, lifting upper and lower eyelids <br />occasionally. Remove contact lenses. Obtain medical attention without delay, <br />preferably from an ophthalmologist.</p> <p>Section 5 – Fire Fighting Measures <br />Extinguishing Media: <br />Other Flammable Properties: <br />flashpoint. <br />Fire Fighting Procedures:</p> <p>Use water spray, alcohol resistant foam, dry chemical or carbon <br />dioxide. <br />Explosive mixtures may occur at temperatures at or above the <br />As in any fire, wear self-contained breathing apparatus pressuredemand, MSHA/NIOSH (approved or equivalent) and full protective <br />gear. Containers can build up pressure if exposed to heat (fire). Cool <br />with water spray. Do not scatter material with high pressure water <br />streams.</p> <p>Hazardous Decomposition Products: Not known.</p> <p>Page 2 of 6</p> <p>IDENTITY: InjectPro-PM3811 Flex-40 <br />(COMPONENT-A–Liquid Resin)</p> <p>SAFETY DATA SHEET <br />SDS No. M1.1.1.B</p> <p>Unusual Fire and Explosion Hazards: Bursting and explosion of container possible due to increase of <br />pressure when exposed to increasing heat. In case of fire, cool nearby <br />containers with water fog.</p> <p>Section 6 – Accidental Release Measures <br />Person-related Safety Precautions:</p> <p>Provide plenty of fresh air. Avoid eye and skin contact. Avoid inhalation <br />of vapors. Wear personal protective equipment.</p> <p>Methods for cleaning-up:</p> <p>Contain and collect spillage with non-combustible, absorbent materials. <br />I.e. sand, earth, vermiculite, diatomaceous earth, universal binders, <br />sawdust and place in container for disposal.</p> <p>Waste Disposal Method:</p> <p>Dispose in accordance with local, state and federal regulations.</p> <p>Ecological Information:</p> <p>Do not allow product to reach ground water, bodies of water, or storm <br />water or sewage systems.</p> <p>Section 7 – Handling and Storage <br />Handling:</p> <p>Avoid breathing vapor or mist. Avoid contact with eyes, skin and clothing. Wash thoroughly <br />after handling. Follow all SDS/label precautions even after the container is emptied because it <br />may retain product residues.</p> <p>Storage:</p> <p>Keep container closed when not in use. Do not store in direct sunlight. Keep in the original <br />container at a temperature not exceeding 30°C (86°F). Store in a cool, dry place. Fill the <br />container by approximately 90% as oxygen (air) is required for stabilization. With large storage <br />containers make sure the oxygen (air) supply is sufficient to ensure stability.</p> <p>Section 8 – Exposure Controls / Personal Protection <br />General Information:</p> <p>Eye-wash bottle must be available. <br />The product does not contain any relevant quantities of materials that have to <br />be monitored at the workplace.</p> <p>Engineering Controls:</p> <p>Use adequate ventilation.</p> <p>Respiratory Protection:</p> <p>Use local exhaust ventilation.</p> <p>Skin Protection:</p> <p>Wear chemical resistant protective clothing and footwear impervious to the <br />product if there is a potential for skin contact.</p> <p>Hand Protection:</p> <p>Glove(s): neoprene.</p> <p>Eye Protection:</p> <p>Use safety goggles or face shield.</p> <p>Other Protective Equipment: A safety shower and eye wash fountain should be readily available. <br />Work/Hygienic Practices:</p> <p>Wash hands before breaks and after work, and before eating, drinking or <br />smoking.</p> <p>Section 9 – Physical and Chemical Properties <br />Page 3 of 6</p> <p>IDENTITY: IDENTITY: InjectPro-PM3811 Flex-40 <br />(COMPONENT-A–Liquid Resin) <br />Physical state: <br />Color: <br />Odor: <br />Solubility in water: <br />pH-value: <br />Boiling point: <br />Flash point: <br />Specific Gravity (water = 1) at 20oC: <br />Viscosity, (kinematic) at 20oC: <br />VOC: <br />Vapor density (air = 1): <br />Vapor pressure: <br />Evaporation rate: <br />VOC: <br />Odor threshold: <br />Auto ignition Temperature: <br />Lower explosion Limit: <br />Upper explosion Limit:</p> <p>SAFETY DATA SHEET <br />SDS No. M1.1.1.B</p> <p>Liquid <br />Clear to brownish <br />Acrylic <br />at 20°C / 68°F miscible <br />N/A <br />>100°C (>212°F) <br />103°C (>217°F) DIN EN 22719 <br />1.07 g/cm3 <br />1 – 3 cps <br />0 g/L <br />is heavier than air <br />0.08 hPa (= mbar) at 20 °C / 68 °F (OECD 104, dynamic method) <br />is slower than butyl acetate <br />0 g/L <br />not available <br />No data available <br />No data available <br />No data available</p> <p>Section 10 – Stability and Reactivity <br />Reactivity:</p> <p>No dangerous reaction known under conditions of normal use.</p> <p>Hazardous Decomposition:</p> <p>None if used as directed.</p> <p>Chemical Stability:</p> <p>Stable under normal temperatures and pressures.</p> <p>Conditions To Avoid:</p> <p>See 'Hazardous Polymerization' for conditions to avoid.</p> <p>Hazardous Polymerization:</p> <p>The product is normally supplied in a stabilized form. If the permissible <br />storage period and/or storage temperature is noticeably exceeded, the <br />product may polymerize with heat evolution. Polymerization with heat <br />evolution may occur in the presence of radical forming substances (e.g. <br />peroxides), reducing substances, and/or heavy metal ions.</p> <p>Incompatibilities:</p> <p>Reducing agents. Tertiary amines. Heavy metals. Peroxides. Oxidizing <br />agents. Mineral acids.</p> <p>Section 11 – Toxicological Information <br />Acute toxicity:</p> <p>None available.</p> <p>Section 12 – Ecological Information <br />Information on Elimination (Persistence and Degradability) <br />• Biodegradability <br />readily degradable, OECD 301 D, Closed Bottle Test, 28 d <br />(plant or external testing) <br />Related to substance: 2-hydroxyethyl methacrylate <br />Ecotoxicological Effect <br />• Fish Toxicity</p> <p>84%</p> <p>227 mg/l <br />Page 4 of 6</p> <p>IDENTITY: InjectPro-PM3811 Flex-40 <br />(COMPONENT-A–Liquid Resin)</p> <p>•</p> <p>•</p> <p>SAFETY DATA SHEET <br />SDS No. M1.1.1.B</p> <p>LC50 Pimephales promelas, flow through, 96 h <br />Related to substance: 2-hydroxyethyl methacrylate <br />Daphnia Toxicity <br />- NOEC Daphnia magna, OECD 202 part 2, flow through, 21 d <br />24.1 mg/l <br />Related to substance: 2-hydroxyethyl methacrylate <br />- EC50 Daphnia magna, OECD 202 part 1, static test, 48 h <br />380 mg/l <br />Related to substance: 2-hydroxyethyl methacrylate <br />Bacteria Toxicity <br />> 3,000 mg/l <br />EC0 Pseudomonas fluorescens, DEV L8, 16 h <br />(plant or external testing) <br />Related to substance: 2-hydroxyethyl methacrylate</p> <p>Further Information on Ecology:</p> <p>Do not allow to enter soil, waterways or waste water.</p> <p>Section 13 – Disposal Considerations <br />Product waste:</p> <p>Must be disposed of in a manner consistent with federal, state and local regulations.</p> <p>Packaging waste:</p> <p>Must be disposed of in a manner consistent with federal, state and local regulations.</p> <p>Section 14 – Transport Information <br />USDOT (Domestic Surface):</p> <p>Not regulated</p> <p>IMO (Ocean):</p> <p>Not regulated</p> <p>IATA/ICAO (Air):</p> <p>Not regulated</p> <p>Section 15 – Regulatory Information <br />TSCA Status:</p> <p>Listed or exempt</p> <p>TSCA Status: <br />SARA 311/312 Hazard <br />Categories (40CFR370):</p> <p>Listed or exempt <br />Acute</p> <p>US State Regulatory Information: <br />Component/CASRN <br />New <br />Jersey <br />RTK <br />2-hydroxyethyl <br />NO <br />methacrylate <br />(CASRN 868-77-9)</p> <p>Pennsylva <br />nia <br />RTK <br />NO</p> <p>Massachuse <br />tts <br />RTK <br />NO</p> <p>California <br />Prop. 65 <br />Cancer <br />NO</p> <p>California <br />Prop. 65 <br />Reproduction <br />NO</p> <p>SARA 313 Notification:</p> <p>This product contains no toxic chemicals subject to the SARA 313 supplier <br />notification requirements.</p> <p>CERCLA:</p> <p>No CERCLA chemicals exist in this product.</p> <p>IDL:</p> <p>Ingredient Disclosure List (IDL), the following components are on the list: <br />Acrylates and methacrylates. <br />Page 5 of 6</p> <p>IDENTITY: IDENTITY: InjectPro-PM3811 Flex-40 <br />(COMPONENT-A–Liquid Resin)</p> <p>SAFETY DATA SHEET <br />SDS No. M1.1.1.B</p> <p>Section 16 – Other Information <br />Abbreviations and acronyms: <br />USDOT: <br />IMDG: <br />IATA: <br />CAS: <br />LC50: <br />LD50:</p> <p>United States Department of Transportation. <br />International Maritime Code for Dangerous Goods. <br />International Air Transport Association. <br />Chemical Abstracts Service (Division of the American Chemical Society). <br />Lethal concentration, 50 percent. <br />Lethal dose, 50 percent.</p> <p>SDS prepared by:</p> <p>Aquafin product safety department.</p> <p>DISCLAIMER: <br />We believe the statements, technical information and recommendations contained herein are reliable, but they are <br />given without warranty or guarantee of any kind, expressed or implied, and we assume no responsibility for any <br />loss, damage, or expense, direct or consequential, arising out of their use. Aquafin shall not be responsible for the <br />use of this product in a manner to infringe on any patent or any other intellectual property rights held by others. <br />User is responsible for determining appropriate safety measures and for applying the legislation covering his own <br />activities. We recommend that user makes tests to determine the suitability of a product for its particular purpose <br />prior to use. <br />END OF SDS</p> <p>Page 6 of 6</p> <p>(March 21, 2024)</p>
