505 Blue Ball Rd. #160
Elkton, MD 21921
Acrylate injection resin
CSI Div. 03 + 31
03 64 00 Injection Grouting
31 73 16 Tunnel Grouting
31 32 23.16 Pressure Grouting Soil Stabilization
Comp-A (PM3811-UltraSeal + Accelerator) Mixable with water in
Aquafin's InjectPro-PM3811 Series of hydrophilic acrylate injection resins
are forumlated with superior sealing characteristics. The InjectPro-3811
acrylates are environmentally safe and include:
1.0 – 1.2 g/ml
8 – 10 mPa-s
InjectPro-PM3811-UltraSeal is specifically formulated for crack injection as
it is not subject to wetting and drying cycles, and therefore do not shrink in
the absence of moisture.
• Controlled, extended setting time range: 4 min – 14 minutes
• Ideal for crack injection, does not shrink in dry environments!
• Free from acrylamides, easy clean-up, non hazardous waste removal
• Certified to NSF/ANSI 61 for potable water
• Crack injection for construction joints, expansion joints, cold joints
• Concrete precast segments
• Creation of grout curtains
• Soil stabilization behind brick and concrete structures
Refer to the Aquafin InjectPro Grouting Guideline for full instructions.
Injection can be accomplished from the inside of the building by drilling
through the structure into the void space and soil back-filled areas.
Packers are placed into pre-drilled holes and the resin is injected using the
AQUAFIN-2K-Inject-Pump, or similar, under low pressure at a 1:1 ratio
by volume. Start pumping at the lowest pressure setting available and
increase gradually as needed.
Reaction times (gel times) can be adjusted so that the material will cure
in time to provide optimum performance depending on the structure and
nature of the repair.
Component A "Resin": Pour desired amount of PM3811-UltraSeal Resin
into a clean bucket and add appropriate amount of Accelerator based on
desired set time (refer to Gel Time Table below) and mix well.
Component B "Hardener": Pour clean, potable water into a seperate
clean bucket, in the exact equal amount as the PM3811-UltraSeal Resin.
Add Hardener Powder based on Gel Time Table below and mix well.
Pumping is 1:1 by volume, example mixing scenario:
Check our website for the latest version of the Technical Datasheet.
Comp-B (Hardener Powder + water) Mixable with water in any ratio.
Clear, low viscous liquid
Accelerator Mixable with water in any ratio.
Blue, viscous liquid
1.0 – 1.2 g/cm³
Hardener Powder (HP)
crystalline dry chemical
1.1 – 1.2 g/cm³
545 g/L at 20°C
Mixed Product - InjectPro-PM3811-UltraSeal
2 – 5 mPa-s
70 – 80%
• Comp A: Measure 100g PM3811-UltraSeal and add
accelerator 5g (=5%) Total: 105g
• Comp B: M
easure 5g (=5%) of the Hardener Powder and add 100g
water (HP + water = 105g).
The reaction time for polymerization depends on the ambient temperature
and the amounts of accelerator and hardener powder used to mix the
• Reaction times can increase due to changes in the temperatures of the
material in the soil. (Higher temp. = faster or shorter gel time. Lower Temp.
= slower or longer gel time.)
• pH of water used to mix Component-B can affect cure times. Potable
water should be used for mixing material and for cleaning pump.
• Avoid mixing large quantities (full pails). This will speed up the gel time.
Page 1 of 2
(updated 02/11/2019-BE, SM)
Reaction time is slower in a thin layer (e.g. in a crack).
General calculation guideline:
If temperature is increased in increments of 10°C (18°F), gel time will be
cut in half. If temperature is decreased by increments of 10°C (18°F), gel
Average Gel Times
4 - 5 min
5 - 7 min
*Times quoted are from laboratory data, reaction times may vary in the field.
Exact reaction times should be determined on site using "cup tests" before starting
The pump and accessories can easily be flushed and cleaned on the
jobsite by using normal detergent and clean water. Hardened material
can be softened with mild cleaners (i.e., Simple Green, 409, etc.) and
easily removed mechanically.
InjectPro-PM3811-UltraSeal is supplied in a kit containing:
• Component-A: 5 gal (44.9 lb) pail
(19 L/20.4 kg) liquid
• Accelerator: 1 quart (2.25 lb) bottle (0.9 L/1.02 kg) liquid
2.2 lb (1.02 kg) powder,
Mix with 5 gal (19 L) water (provide on site)
Component-A is ready for use after being mixed with the accelerator
supplied. Component-B is made up at the jobsite by dissolving the
hardener powder in potable water.
InjectPro-PM3811-UltraSeal is injected using a 2-component pump with
stainless steel mixing parts, such as the AQUAFIN-2K-Inject-Pump.
All details in particular to the suggestions for the processing and use of the
product is based on our present knowledge and experiences at the time
of printing. Depending on specific applications, in particular regarding
substrates, processing and environmental conditions may affect the final
Safety and Handling:
InjectPro-PM3811-UltraSeal contains no toxic components. Acrylate-ester,
acrylic monomers can irritate the eyes and skin. Sensitivity to the product
is possible if it comes in direct contact with the skin. During use wear
protective clothing, gloves, and appropriate safety goggles consistent with
OSHA regulations. Avoid eye and skin contact. Do not ingest. Refer to
Material Safety Data Sheet for detailed safety precautions. Hardened PM3811-UltraSeal is environmentally safe and can be disposed of as normal
household waste. CAUTION: Do not use aluminum equipment near the
accelerator and hardener powder, they are not compatible with aluminum.
Refer to MSDS. KEEP OUT OF REACH OF CHILDREN.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a
period of one year from the date of installation to be manufactured free
of defects and to be consistent with its technical properties as stated in our
current Technical Data Sheet. This product must be used as directed and
within its stated shelf life. AQUAFIN INC. will replace or at our discretion
refund the purchase price of any product, excluding cost of labor, which
is proven to be defective. Our product recommendations are based on
industry standards and testing procedures. It is the buyer’s obligation to test
the suitability of the product for an intended use prior to using it. We assume
no warranties written, expressed or implied as to any specific methods of
application or use of the product.
For Professional Use Only.
Shelf life is 12 months in closed, original packaging, stored in a dry, cool
InjectPro-PM3811-UltraSeal should be stored in a dry enclosure in closed
containers at temperatures between 50°F to 86°F. (10°C to 30°C).
Protect product and packaging from inclement weather. CAUTION: Do
not let the accelerator and hardener powder come in contact during
storage. Store individual components seperately from each other.
Certified to NSF/ANSI Standard 61
see www.wqa.org for use restrictions
Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact
our technical department for further information before starting any applications.
Page 2 of 2
(updated 02/11/2019-BE, SM)