505 Blue Ball Rd. #160
Elkton, MD 21921
Hydrophobic, rigid polyurethane grout for stopping active leaks in cracks and filling voids
No harmful phthalates
CSI Div. 03
03 64 00 Injection Grouting
InjectProECO-Cut is a high performance, hydrophobic polyurethane
injection grout which cures to a rigid, durable, closed celled foam. It is
designed to fill joints and cracks in concrete, as well as large voids in
gravel layers and rock fissures. Due to its quick cure time it can also be
used to stop active, high flow water leaks. When it comes in contact with
water, the grout expands and quickly cures to a tough, flexible, closedcell polyurethane foam that is generally unaffected by common corrosive
environments and is not subject to shrinkage due to wet/dry cycles.
InjectProECO grouts are all environmentally friendly and formulated without
harmful phthalates or VOC’s.
The system is comprised of an “A” component (base resin) and a “B”
component (accelerator). The “B” component is used by the applicator to
adjust the set times for various job site specific conditions.
Any concrete structure with larger volume water leaks such as:
• Water retaining structures, foundations, waste water treatment plants
& manholes, concrete dams, tunnels, parking garages, etc.
• Zero VOC’s - meets LEED criteria
• 100% solids, non-flammable, non-toxic permanent seal
• Hydrophobic - can be used in wet and dry environments
• Accelerator and resin stable to -40°F.
• Pumped as a single component
• Can expand more than 25 times initial volume
• Adjustable reaction times
• Excellent resistance and durability
• Pumps well even at lower temperatures
• Non-hazardous shipping
Reaction Times & Use of Accelerator:
The reaction time can be adjusted by the addition of accelerator “B”
into the base resin prior to pumping. The resulting profile is affected by
temperature and the amount of moisture present.
Typical reaction times:
Accelerator % Reaction
Refer to the Aquafin InjectPro Grouting Guideline for full instructions. Mix
both the resin (Component A) and accelerator (Component B) before
Check our website for the latest version of the Technical Datasheet.
Viscosity (ASTM D-1638)
Specific Gravity (ASTM D-1475)
Flash Point (ASTM D-92)
Solid (cured) InjectProECO-Cut
Density (ASTM D-1622)
Elongation (ASTM D-638)
Tensile Strength (ASTM D-638)
Shear Strength (ASTM C-273)
Water Absorption (ASTM D-2842)
• Pour the desired amount of InjectProECO-Cut Resin Component A into a
• Measure the appropriate amount of InjectProECO-ACCELERATOR-CCS
Component B and pour into the InjectProECO-Cut Resin, stirring until
adequately mixed. Never use more accelerator than recommended.
Excess accelerator will cause significant expansion that is prone to
shrinkage. For faster reaction times please contact technical services for
information on InjectProECO-ACCELERATOR-CCS-FAST.
During injection, the grout will follow the path of least resistance. When
the material has stopped penetrating it will continue to expand against the
confines of the crack/joint and compress within itself, forming a very dense,
closed cell material stopping the leak.
5 gallon pails
32 oz. containers
(5% dosage per 5 gallons of resin. For 10% acceleration use 2 x 32 oz.)
Storage & Shelf Life:
Shelf life is two years when stored properly. Product is highly moisture
sensitive. Store in original sealed containers at temperature between 40°F
– 90°F. Opened containers must be handled properly to prevent moisture
• Temperature significantly affects viscosity. Protect material from
excessive heating and cooling prior to grouting to avoid affecting
• If using water baths to cool or heat pails avoid splashes to prevent
water coming in direct contact with resin - this will activate the reaction.
Do not warm material or packaging above 90°F.
Page 1 of 2
• Do not reseal containers of contaminated materials as it can create
• Clean up spills with adequate ventilation and appropriate personal
protective equipment. Cover the spill area with absorbent material
such as clay or vermiculite and transfer to metal waste containers.
Wash area with decontamination solution (5-10% solution of sodium
carbonate). Dispose of waste in accordance with federal, state and
Proper application is the responsibility of the user. Field visits by AQUAFIN
personnel are for the purpose of making technical recommendations and
not for supervising or providing quality control on-site.
Refer to SDS. For commercial use only. Avoid contact with skin and eyes.
Wear rubber gloves and safety goggles during mixing and application.
After contact with skin, wash with plenty of water. In case of eye contact,
rinse immediately with plenty of water for 15 minutes and seek medical
advice. KEEP OUT OF REACH OF CHILDREN.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year
from the date of installation to be manufactured free of defects and to be consistent
with its technical properties as stated in our current Technical Data Sheet. This product
must be used as directed and within its stated shelf life. AQUAFIN INC. will replace
or at our discretion refund the purchase price of any product, excluding cost of
labor, which is proven to be defective. Our product recommendations are based
on industry standards and testing procedures. It is the buyer’s obligation to test the
suitability of the product for an intended use prior to using it. We assume no warranties
written, expressed or implied as to any specific methods of application or use of the
product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable
for damages of any sort including remote or consequential damages, down time, or
delay. Any claim for a defective product must be filed within 30 days of discovery of a
problem, and must be submitted with written proof of purchase.
For Professional Use Only.
Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact
our technical department for further information before starting any applications.
Page 2 of 2