505 Blue Ball Rd. #160
Elkton, MD 21921
Hydrophobic, flexible polyurethane grout for stopping active leaks in cracks
No harmful phthalates
CSI Div. 03
03 64 00 Injection Grouting
InjectProECO-LV is a closed cell, high performance polyurethane injection
grout designed for use to cut off gushing water leaks with a high flow
rate and/or high hydrostatic pressure in low range dynamic cracks.
When it comes in contact with water, the grout expands up to 800%
and quickly cures to a tough, flexible, closed-cell polyurethane foam that
is generally unaffected by common corrosive environments and is not
subject to shrinkage due to wet/dry cycles. InjectProECO grouts are all
environmentally friendly and formulated without harmful phthalates or
The system is comprised of an “A” component (base resin) and a “B”
component (accelerator). The “B” component is used by the applicator to
adjust the set times for various job site specific conditions.
Any concrete structure with water leaks such as:
• Water Retaining Structures, Concrete Dams, Tunnels, Elevator Pits,
Parking Garages, etc.
• Zero VOC’s - meets LEED criteria
• 100% solids, non-flammable, non-toxic permanent seal
• Hydrophobic - can be used in wet and dry environments
• Accelerator and resin stable to -40°F.
• Pumped as a single component
• Excellent elongation creates a tight seal in moving cracks
• Adjustable reaction times
• Non-hazardous shipping
Reaction Times & Use of Accelerator:
The reaction time can be adjusted by the addition of accelerator “B”
into the base resin prior to pumping. The resulting profile is affected by
temperature and the amount of moisture present.
Typical reaction times:
Accelerator % Reaction
Refer to the Aquafin InjectPro Grouting Guideline for full instructions. Mix
both the resin (Component A) and accelerator (Component B) before
• Pour the desired amount of InjectProECO-LV Resin Component A into a
• Measure the appropriate amount of InjectProECO-LV Accelerator
Component B and pour into the InjectProECO-LV Resin, stirring until
Check our website for the latest version of the Technical Data Sheet.
Physical Properties - liquid
Solids (ASTM D2369)
Viscosity (ASTM D1638)
Density (ASTM D4659)
~67 lbs. ft3
~57 lbs. ft3
Flash Point (ASTM D92)
Physical Properties - solid (cured) InjectProECO-LV
Density - Free Foam (ASTM D1622)
Density - Confined (ASTM D1622)
Compressive Strength (contingent on confinement)
adequately mixed. Never use more accelerator than recommended.
Excess accelerator will cause significant expansion that is prone to
During injection, the grout will follow the path of least resistance. When
the material has stopped penetrating it will continue to expand against the
confines of the crack/joint and compress within itself, forming a very dense,
closed cell material stopping the leak.
5 gallon pails
InjectProECO-LV Accelerator: 32 oz. container
(5% dosage per 5 gallons of resin. For 10% acceleration use 2 x 32 oz.)
Storage & Shelf Life:
Shelf life is two years when stored properly. Product is highly moisture
sensitive. Store in original sealed containers at temperature between 40°F
– 90°F. Opened containers must be handled properly to prevent moisture
• Temperature significantly affects viscosity. Protect material from excessive
heating and cooling prior to grouting to avoid affecting viscosity.
• If using water baths to cool or heat pails avoid splashes to prevent water
coming in direct contact with resin - this will activate the reaction. Do not
warm material or packaging above 90°F.
• Do not reseal containers of contaminated materials as it can create pressure.
• Clean up spills with adequate ventilation and appropriate personal
protective equipment. Cover the spill area with absorbent material
such as clay or vermiculite and transfer to metal waste containers.
Wash area with decontamination solution (5-10% solution of sodium
carbonate). Dispose of waste in accordance with federal, state and
Page 1 of 2
Proper application is the responsibility of the user. Field visits by AQUAFIN
personnel are for the purpose of making technical recommendations and
not for supervising or providing quality control on-site.
Refer to SDS. For commercial use only. Avoid contact with skin and eyes.
Wear rubber gloves and safety goggles during mixing and application.
After contact with skin, wash with plenty of water. In case of eye contact,
rinse immediately with plenty of water for 15 minutes and seek medical
advice. KEEP OUT OF REACH OF CHILDREN.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year
from the date of installation to be manufactured free of defects and to be consistent
with its technical properties as stated in our current Technical Data Sheet. This product
must be used as directed and within its stated shelf life. AQUAFIN INC. will replace
or at our discretion refund the purchase price of any product, excluding cost of labor,
which is proven to be defective. Our product recommendations are based on industry
standards and testing procedures. It is the buyer’s obligation to test the suitability of
the product for an intended use prior to using it. We assume no warranties written,
expressed or implied as to any specific methods of application or use of the product.
AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable
for damages of any sort including remote or consequential damages, down time, or
delay. Any claim for a defective product must be filed within 30 days of discovery of a
problem, and must be submitted with written proof of purchase.
For Professional Use Only.
Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact
our technical department for further information before starting any applications.
Page 2 of 2