505 Blue Ball Rd. #160
Elkton, MD 21921
Hydrophobic, polyurethane grout for stabilizing and waterproofing loose, granular soils
No harmful phthalates
CSI Div. 03
03 64 00 Injection Grouting
InjectProECO-Soil is a next generation ultra low viscosity, single
component, hydrophobic polyurethane injection grout for stabilization
of granular soils. When it comes in contact with water InjectPro-ECOSoil expands and then cures to a high strength, rigid and durable foam.
It’s unique formulation allows the grout to fully encapsulate granulas,
thereby creating a stable and solid mass. InjectProECO grouts are all
environmentally friendly and formulated without harmful phthalates or
• Soil stabilization for seawalls, excavation sites, tunnels, etc.
• Structural support around building foundations
• Erosion control
• Stopping below grade foundation leaks
• Zero VOC’s - meets LEED criteria
• 100% solids, non-flammable, non-toxic permanent seal
• Accelerator and resin stable to -40°F.
• Hydrophobic - can be used in wet and dry environments
• Pumped as a single component
• Very low viscosity for excellent penetration into various soil types
• Adjustable reaction times
• Non-hazardous shipping
Reaction Times & Use of Accelerator:
The reaction time can be adjusted by the addition of accelerator “B”
into the base resin prior to pumping. The resulting profile is affected by
temperature and the amount of moisture present.
Typical reaction times:
Accelerator % Reaction
Refer to the Aquafin InjectPro Grouting Guideline for full instructions. Mix
both the grout (component A) and accelerator (component B) before
• InjectPro-ECO-Soil can be pumped as supplied.
• Alternately, the reaction time can be adjusted prior to pumping by
adding Inject-Pro Accelerator into the grout and will be affected by
temperature and the moisture content of the soil. Never use more
accelerator than recommended. Excess accelerator will cause
significant expansion that is prone to shrinkage.
Check our website for the latest version of the Technical Datasheet.
Viscosity (ASTM D-1638)
Density (ASTM D-4659)
Flash Point (ASTM D-92)
Solids (ASTM D-2369)
Solid (cured) ECO-Soil
Density Free Foam (ASTM D3574)
2.2 lbs. / ft3
Density Confined (ASTM D3574)
87.4 lbs. / ft3
Compressive Strength (Contingent on Soil Matrix)
800 to 4600 psi
5 gallon pails or 50 gallon drum
InjectProECO-Soil Accelerator: 32 oz. container or 5 gallon pail
Storage & Shelf Life:
Shelf life is 2 years when stored properly. Product is highly moisture
sensitive. Store in original sealed containers at temperature between 40°F
– 90°F. Opened containers must be handled properly to prevent moisture
• Temperature significantly affects viscosity. Protect material from
excessive heating and cooling prior to grouting to avoid affecting
• If using water baths to cool or heat pails avoid splashes to prevent
water coming in direct contact with resin - this will activate the reaction.
Do not warm above 90°F.
• Do not reseal containers of contaminated materials as it can create
• Clean up spills with adequate ventilation and appropriate personal
protective equipment. Cover the spill area with absorbent material
such as clay or vermiculite and transfer to metal waste containers.
Wash area with decontamination solution (5-10% solution of sodium
carbonate). Dispose of waste in accordance with federal, state and
Proper application is the responsibility of the user. Field visits by AQUAFIN
personnel are for the purpose of making technical recommendations and
not for supervising or providing quality control on-site.
Page 1 of 2
Refer to SDS. For commercial use only. Avoid contact with skin and eyes.
Wear rubber gloves and safety goggles during mixing and application.
After contact with skin, wash with plenty of water. In case of eye contact,
rinse immediately with plenty of water for 15 minutes and seek medical
advice. KEEP OUT OF REACH OF CHILDREN.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year
from the date of installation to be manufactured free of defects and to be consistent
with its technical properties as stated in our current Technical Data Sheet. This product
must be used as directed and within its stated shelf life. AQUAFIN INC. will replace
or at our discretion refund the purchase price of any product, excluding cost of
labor, which is proven to be defective. Our product recommendations are based
on industry standards and testing procedures. It is the buyer’s obligation to test the
suitability of the product for an intended use prior to using it. We assume no warranties
written, expressed or implied as to any specific methods of application or use of the
product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable
for damages of any sort including remote or consequential damages, down time, or
delay. Any claim for a defective product must be filed within 30 days of discovery of a
problem, and must be submitted with written proof of purchase.
For Professional Use Only.
Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact
our technical department for further information before starting any applications.
Page 2 of 2