TDS-MORTAR-LN_051826.pdf
4 Pages
131 KB
Download
<h1>TDS-MORTAR-LN_051826.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />e: info@aquafin.net <br />e: technical@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>MORTAR-LN</p> <p>One-part, polymer-modified, waterproof lining mortar, resurfacing mortar, and parge coat <br />CSI Div. 03, 04, 09 + 33 <br />03 01 30 Maintenance of Cast-in-Place Concrete <br />03 01 30.61 Resurfacing Cast-in-Place Concrete <br />03 01 30.71 Rehabilitation of Cast-in-Place Concrete <br />04 01 00 Maintenance of Masonry <br />04 01 20.51 Unit Masonry Maintenance <br />04 01 40.51 Stone Maintenance <br />09 24 33 Cement Parging <br />33 01 10 Operation and Maintenance of Water Utilities <br />33 16 00 Water Utility Storage Tanks <br />33 16 36 Ground-Level Reinforced Concrete Water Storage Tanks <br />33 16 61 Underground Concrete Water Storage Cisterns <br />33 49 23 Storm Drainage Water Retention Structures <br />LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />MORTAR-LN is a fast-curing, cementitious, polymer-modified waterproof <br />lining mortar, resurfacing mortar, and parge coat for concrete and masonry <br />substrates. It‘s unique hydrophobic (water repellent) properties prevents <br />water infiltration or exfiltration through the cured product. MORTAR-LN <br />is specially designed to work in conjunction with AQUAFIN-1K and <br />AQUAFIN-2K/M waterproofing products. <br />Typical Applications: <br />MORTAR-LN is commonly used for non-structural repairs and resurfacing <br />in basements, elevator pits, and water holding tanks. It is widely <br />recommended for horizontal, vertical, and overhead applications, both <br />above and below grade such as: <br />• Parging interior brick and rubble stone walls in preparation for <br />AQUAFIN-1K and/or AQUAFIN-2KM waterproofing <br />• Resurfacing interior concrete floors, ceilings, and walls <br />• Rehabilitating concrete water tanks to receive AQUAFIN-1K and <br />AQUAFIN-2KM waterproofing <br />• Installation of seal strips (reglets and cants/coves) at perimeter joint <br />locations (floor-to-wall transitions), corners (wall-to-wall transitions), and <br />wall-to-ceiling joints <br />• Patching and filling of routed out static (non-moving) cracks, tie-holes, <br />and drill holes in concrete and masonry <br />Advantages: <br />• Slow Setting <br />• Waterproof/Water impermeable <br />• NSF/ANSI/CAN 61potable water certified (www.wqa.org) <br />• Horizontal - Vertical - Overhead <br />• Resists hydrostatic pressure <br />• Applied to damp (moist) substrates <br />• Applied to the positive or negative water pressure side of a structure <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Physical and Technical Data <br />Aggregate State:</p> <p>Powder</p> <p>Color:</p> <p>Concrete gray</p> <p>Bulk Density:</p> <p>~100 lb/ft³ (~1.6 kg/dm³)</p> <p>VOC:</p> <p>0 g/L</p> <p>Compressive Strength <br />(ASTM C-109 and <br />EN 196/1):</p> <p>24 hrs.: 700 psi (4.8 MPa) <br />3 days: 2100 psi (14.5 MPa) <br />7 days: 4700 psi (32.4 MPa) <br />28 days: 6000 psi (41.4 MPa)</p> <p>Flexural Strength <br />(ASTM C-348 and <br />EN 196/1):</p> <p>24 hrs.: 30 psi (0.2 MPa) <br />3 days: 620 psi (4.3 MPa) <br />7 days: 870 psi (6.0 MPa) <br />28 days: 1160 psi (8.0 MPa)</p> <p>Shrinkage:</p> <p>28 days: 0.023%</p> <p>Adhesion (ASTM C-321):</p> <p>28 days: >220 psi (>1.5 MPa)</p> <p>Water Permeability: control <br />LN @ 1/8” thickness: <br />LN @ 1/8” thickness :</p> <p>1.58 x 10-7 cm/s @ 3 d <br />3.60 x 10-9 cm/s @ 3 d <br />2.36 x 10-10 cm/s @ 28 d Note: 100</p> <p>Application time: <br />Setting Time:</p> <p>Approx. 30 minutes <br />Approx. 5−6 hours</p> <p>Potable water certified:</p> <p>NSF/ANSI/CAN 61: www.wqa.org</p> <p>psi (234 ft. head pressure) positive side</p> <p>All data are average values obtained under laboratory conditions. In practical <br />use temperature, humidity, and absorbency of the substrate may influence the <br />above given values</p> <p>• Not a vapor barrier, lets substrate “breathe” <br />• Easy to use -- needs only to be mixed with water <br />• Applied by glove pointing, trowel or low pressure air-spraying (guniting) <br />• No odor -- No fumes -- Environmentally friendly <br />Substrate Preparation: <br />• All substrates must be strong, solid, stable, and of load bearing capacity. <br />• Areas designated to receive repairs must remain structurally sound <br />and stable during demolition and surface preparation work, and these <br />conditions must continue throughout the course of the repair work. Any <br />areas of concern or uncertainty should be discussed immediately with <br />the site Superintendent and brought to the attention of the Engineer of <br />record. <br />• If water is accumulating from an active leak(s) through cracks or joints in <br />masonry walls, concrete walls, or concrete floors, Aquafin recommends <br />the process of injection grouting as a first step in stopping severe water <br />intrusion. For more information about Aquafin’s extensive line of Injection <br />Grouts, contact your local Aquafin Representative. <br />• Leaking cracks and other minor leaks (with little to no water <br />accumulation) can be plugged using MORTAR-LN. Refer to the current <br />MORTAR-LN Technical Data Sheet for preparation instructions and other <br />Page 1 of 4 <br />(05/18/26-EK,AC)</p> <p>MORTAR-LN <br />important information. <br />• Substrates must be clean and free from all potential bond breakers <br />such as sand, dirt, dust, efflorescence and mineral deposits, grease, oil, <br />previous coatings, paint, sealers, water repellants, curing compounds, <br />etc. Mechanically clean the substrate to remove any bond-inhibiting <br />substances and/or contaminants. <br />• Mechanically prepare all surfaces (including new concrete and new <br />masonry) to achieve a surface profile equal to CSP 5-7 as per ICRI <br />Guideline No. 310.2R-13. Shot blasting, and hydro blasting (high <br />pressure water-blasting at > 5,000 psi) are the preferred methods. <br />• Properly clean mechanically profiled area(s) by hydro blasting (waterblasting) or thorough pressure washing. <br />• Pre-water (thoroughly soak) the substrate extremely well with clean <br />water. Pay particular attention to substrates with excessive absorption <br />such as CMU-block walls and any substrate during hot/windy <br />conditions. <br />• All surfaces must be saturated surface dry (SSD), which is damp but with <br />no standing water, immediately prior to the application of MORTAR-LN. <br />In addition to general surface preparation requirements listed above, <br />supplementary instructions for specific types of repairs and surface <br />conditions are provided below: <br />•B <br /> rick, CMU Block, Rubble Stone Walls, and Masonry Joints: <br />• R epair any loose brick, CMU block, stone or rubble on masonry <br />walls. <br />• R emove cracked, damaged, and loose mortar from masonry joints. <br />• R emove all dirt and debris from masonry joints with a brush or with <br />compressed air. <br />• F lush joints clean with water and leave damp. <br />•N <br /> on-Leaking, Static Cracks and Static Cracks with Minor Leaks <br />Exceeding 0.02” (0.4 mm): <br />• R out out non-leaking, static (non-moving) cracks to a U-shaped <br />configuration, appx. ¾” (19 mm) wide and a minimum of 1” (25 <br />mm) deep. <br />• R emove all dirt and debris from routed cracks with a brush or with <br />compressed air. <br />• F lush cracks clean with water and leave damp. <br />•C <br /> oncrete Walls and Floors (including bug holes): <br />•N <br /> ew concrete must be at least 5 days old, or concrete must have <br />reached a minimum 2,500 psi (17.2 MPa) compressive strength. <br />•M <br /> echanically remove all laitance, loose or deteriorated concrete <br />by suitable means such as chipping hammer, chisel, sandblast, <br />high pressure water blast (hydro blast) at greater than 5000 psi, or <br />similar methods. <br />• P repare minor surface voids and bug holes by using recommended <br />mechanical preparation methods (shotblasting, hydro blasting, etc.) <br />•C <br /> lean mechanically profiled area(s) by hydro blasting (waterblasting) or thorough pressure washing and leave damp. <br />•D <br /> rilled Injection Grouting Holes and Tie Holes: <br />• R emove dirt and debris from tie holes and drilled holes with a <br />cylindrical bristle brush. <br />• F lush holes clean with water and leave damp. <br />•R <br /> eglet in Perimeter Joint or Wall-to-Ceiling Joint: <br />• Saw cut a ¾ in. to 1½ in. (19 mm to 38 mm) deep by <br />approximately 1 in. (25 mm) high horizontal groove into the <br />concrete or masonry wall at the perimeter joint location and/or <br />where the concrete or masonry wall meets the concrete ceiling. <br />• R emove all dirt and debris from cavity with a brush or with <br />compressed air. <br />• Flush reglets clean with water and leave damp. <br />•R <br /> eglet in Corner Joint: <br />• Saw cut a ¼ in. to ½ in. (6 mm to 12 mm) wide by ½ in. to ¾</p> <p>in. (12 mm to 19 mm) deep vertical groove into the corner joints <br />spanning the entire vertical length of the corner joints where two <br />walls meet. <br />• R emove all dirt and debris from cavity with a brush or with <br />compressed air. <br />• F lush reglets clean with water and leave damp. <br />•S <br /> teel Pipes and Welds: <br />•C <br /> lean steel pipe surfaces and welds to white steel. <br />Jobsite Conditions & Preparation <br />•O <br /> nly proceed with application when ambient and surface temperatures <br />are above 40°F (4°C) and rising and below 90°F (32°C). <br />•D <br /> o not apply MORTAR-LN when temperatures are expected to fall <br />below 40°F (4°C) within 24 hours after placement. <br />•D <br /> o not apply MORTAR-LN to frozen or frost covered concrete surfaces. <br />• Do not apply MORTAR-LN when rain is expected within 6 hours after <br />placement. <br />• When applying MORTAR-LN in temperatures at or above 85°F <br />(29°C), follow ACI hot-weather application guidelines to ensure a <br />successful installation. <br />Mixing Instructions: <br />Read all instructions thoroughly prior to mixing and application. <br />• Precondition MORTAR-LN to ~70°F (21°C) prior to mixing. <br />• Use an accurate measuring container and always carefully measure the <br />water amounts. <br />For Each: <br />Add: <br />50.0 lb (22.7 kg) bag</p> <p>0.8 to 1.1 gal (3.0 to 4.2 L) of clean water</p> <p>• Add the appropriate amount of potable water into a clean mixing <br />bucket. Start with lowest water amount per mixing ratio. <br />• Gradually add powder 1/3 at a time while mixing continuously. <br />• For best results, mechanically mix at slow speed with a ¾” (19 mm) drill <br />and “Jiffy” mixing paddle. Use a paddle type mortar mixer for large jobs. <br />• Mix at slow speeds to prevent entraining air for a minimum of 3 minutes <br />or until a lump-free consistency is achieved. <br />• Add remaining amount of water, a little at a time, up to the highest <br />water amount per mixing ratio if needed for workability. DO NOT <br />OVERWATER! If too much water is added, the mixture tends to <br />segregate resulting in uneven surface strengths. Surfaces with reduced <br />strength must be removed mechanically. <br />Note: Due to the MORTAR-LN hydrophobic characteristics, it takes up to <br />30 (thirty) seconds for mixing water to combine with the dry powder mix. <br />Application Instructions: <br />• Always apply MORTAR-LN over damp, SSD substrates. <br />• MORTAR-LN may be applied using a flat trowel or using suitable mortar <br />spray equipment such as gunite spray equipment or a peristaltic pump <br />(i.e. Quikspray carrousel pump). <br />• P arge Coats on Concrete, Brick, and Rubble Stone Walls: <br />•M <br /> ix Aquafin MORTAR-LN with water to the consistency of a slurry <br />and apply to the brick walls as a bond coat using a masonry <br />brush. <br />•W <br /> hile the bond coat of MORTAR-LN is still fresh/wet, apply a <br />1/8” to 1” (3 mm to 25 mm) thick parge coat of MORTAR-LN on <br />the brick or rubble stone walls to fill in any missing mortar in the <br />mortar joints and create a flush, even surface. <br />• F or rubble stone walls, if there are still surface variations after the <br />first parge coat, then finish MORTAR-LN with a rough texture while <br />still fresh in order to facilitate the bond for the next layer. Allow to <br />cure until set (approx. 5 to 6 hrs.). Repeat the process as needed <br />until the surface of the rubble stone wall is flush and even (dampen</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 4 <br />www.aquafin.net <br />(05/18/26-EK,AC)</p> <p>MORTAR-LN <br />the surface of the underlying application of MORTAR-LN, apply <br />a slurry bond coat of MORTAR-LN, apply another 1/8” to 1” (3 <br />mm to 25 mm) thick parge coat of MORTAR-LN, and finish with a <br />rough texture if an additional layer is needed). <br />Note: In order for MORTAR-LN to function as negative side waterproofing <br />without an additional coating such as AQUAFIN®-1K, apply MORTAR-LN <br />as a continuous void-free mortar at a minimum of ¼” (6 mm) thick across <br />the entire application area. <br />•H <br /> orizontal Concrete Repairs and Resurfacing: <br />• P our MORTAR-LN in one working cycle at ¼” to 1” (6 mm to 25 <br />mm) over horizontal surfaces, then compact and strike off. <br />• Trowel-Applied Vertical/Overhead Concrete Repairs and Resurfacing: <br />•M <br /> ix Aquafin MORTAR-LN with water to the consistency of a slurry <br />and apply as a bond coat using a masonry brush. <br />•W <br /> hile the bond coat is still fresh/wet, perform concrete patching, <br />repairs, and resurfacing from 1/8” to 1” (3 mm to 25 mm) thick <br />with MORTAR-LN and create a flush, even surface. <br />• If multiple lifts are required, finish MORTAR-LN with a rough texture <br />while still fresh in order to facilitate the bond for the next layer. <br />Allow to cure until set (approx. 5 to 6 hrs.). Repeat the process; <br />dampen the surface of the underlying application of MORTAR-LN, <br />apply a slurry bond coat of MORTAR-LN, and perform repairs from <br />1/8” to 1” (3 mm to 25 mm) thick. <br />• Spray-Application on Vertical/Overhead Concrete and Masonry: <br />•S <br /> pray apply MORTAR-LN from 1/8” to 1” (3 mm to 25 mm) thick <br />per lift. <br />•M <br /> etal lath (stucco netting, diamond lath, chicken wire, etc.) can <br />be used to facilitate placement of MORTAR-LN in vertical spray <br />applications. <br />• If multiple lifts are required, allow MORTAR-LN to cure until set <br />(approx. 5 to 6 hrs.). Dampen the surface of MORTAR-LN and <br />repeat spray application from 1/8” to 1” (3 mm to 25 mm) thick. <br />• Patch and Fill Routed Static Cracks, Tie Holes, Drill Holes, Masonry <br />Joints, Reglet Cavities, and Surface Voids: <br />• F ill prepared cracks, holes, reglet cavities, and voids, flush to <br />surface with MORTAR- LN. <br />•C <br /> reate Triangular Cant/Cove in Perimeter Joints (Floor-to-Wall Joints), <br />Corner Joints (Wall-to-Wall Joints) or Wall-to-Ceiling Joints: <br />•U <br /> se MORTAR-LN to form a 2” x 2” (51 mm x 51 mm) or a 1.5” x <br />1.5” (38 mm x 38 mm) triangular cant/cove over perimeter joints <br />where the concrete floor meets the concrete or masonry wall, <br />and/or over corners where two concrete or masonry walls meet, <br />and/or over the joint where the concrete or masonry wall meets <br />the concrete ceiling. <br />Finish & Top Coating: <br />• Surface Finish: Final layer may be troweled smooth/flat, broomed to <br />increase non-skid quality, or sprayed with orange peel texture. <br />•C <br /> oncrete Joints: Re-establish all previously existing concrete joints within <br />2 hours of final set. <br />• Top Coating with AQUAFIN-1K or AQUAFIN-2K/M: AQUAFIN®-1K <br />or AQUAFIN®-2K/M can be applied as soon as MORTAR-LN has set <br />(~5−6 hours). <br />• Top Coating with Breathable Paint: Where specified or desired, <br />MORTAR-LN can receive a breathable, water-based, acrylic paint. after <br />3 days. <br />• Top Coating with Non-Breathable Paint or Coatings: Where specified <br />or desired, MORTAR-LN can receive non-breathable, non-vapor <br />permeable, paints or coatings (such as epoxy coatings) after 7 days. <br />Note: MORTAR-LN does not function as a vapor barrier. If there is <br />evidence of dampness coming through walls, contact Aquafin Technical <br />Department for advice prior to specifying or applying moisture-sensitive <br />coatings on walls. If there is evidence of a moisture vapor issue(s) <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>in the concrete floor slab, Aquafin recommends the application of a <br />topical epoxy vapor barrier prior to the application of moisture-sensitive <br />floor coatings. For more information about Aquafin’s Vaportight Coat <br />products visit: www.vaportightcoat.com or contact your local Aquafin <br />Representative. <br />Protection: <br />• Protect from freezing for 24 hours after application. <br />Curing: <br />• Standard Application with Top Coat of AQUAFIN®-1K or 2K/M: <br />•D <br /> amp cure MORTAR-LN for approximately 5 to 6 hours, or until <br />set. <br />•A <br /> pply AQUAFIN®-1K or AQUAFIN®-2K/M over MORTAR-LN <br />while it is still green. <br />• Potable Water Applications to be left exposed (without AQUAFIN®1K or 2K/M as a Top Coat): <br />• P otable water applications that will not receive AQUAFIN®-1K <br />or AQUAFIN®-2K/M as a top coat, MORTAR-LN must be damp <br />cured for at least 7 days. Begin curing as soon as MORTAR-LN <br />has set by keeping surface moist as per ACI recommendations for <br />Portland cement concrete, using wet burlap, polyethylene or a fine <br />mist of water. <br />Note: Higher temperatures will reduce the curing time. <br />Clean-up: <br />• Thoroughly clean all tools and other equipment with water prior to the <br />material reaching final set. <br />• Cured material must be mechanically removed. <br />Limitations: <br />• Curing times and set times are approximate and will vary depending <br />on ambient (air) temperature, mix water temperature, the temperature of <br />MORTAR-LN dry powder in the packaging, surface temperature of host <br />concrete or host masonry, profile of the host concrete or host masonry, <br />and the application thickness. <br />• Do not add sand, aggregate, cement or other ingredients to the mix. <br />• Do not add accelerators, retarders or admixtures to the mix. <br />• Do not featheredge or apply MORTAR-LN less than 1/8” (3 mm) thick. <br />• Do not exceed the maximum 1” (25 mm) thickness per lift. <br />• Do not use MORTAR-LN in swimming pools, water falls in swimming <br />pools, hot tubs, or fountains. <br />•M <br /> ORTAR-LN is not recommended for filling concrete joints (cold joints, <br />construction joints, contraction joints, expansion joints, etc.). Always reestablish movement joints when using MORTAR-LN. <br />• MORTAR-LN is not recommended for application over hollow terracotta <br />masonry (old structural clay tile). <br />• Do not re-temper or use additional water during the finishing process. <br />The addition of excess water will negatively affect the material’s final <br />properties and appearance. <br />• Like all cementitious products, variations in temperature, humidity, <br />substrate moisture, air movement, application methods, and finishing <br />techniques, will contribute to the end look of the finished product. <br />Consistency in areas mentioned above typically yield a relatively <br />uniform result. However, color uniformity of MORTAR-LN is not <br />guaranteed. <br />• Do not use MORTAR-LN as a structural repair mortar. If structural <br />repairs are needed, consult a licensed Engineer and ask an Aquafin <br />Representative about Aquafin structural repair products such as <br />MORTAR-40 CI. <br />• In exterior applications, MORTAR-LN must be finished with a paint or <br />coating for protection from long-term UV exposure. <br />Page 3 of 4 <br />(05/18/26-EK,AC)</p> <p>MORTAR-LN <br />Packaging: <br />50 lb. (22.7 kg) bags</p> <p>KEEP OUT OF REACH OF CHILDREN.</p> <p>Storage and Shelf Life: <br />Storage: Store MORTAR-LN in unopened, original, undamaged bags in a <br />dry enclosed area, off the ground in temperatures between 55°F – 90°F <br />(13°C - 32°C). <br />Shelf Life: 1 year when stored according to conditions listed above. <br />Note: <br />Proper application is the sole responsibility of the user. Applicators <br />are expected to follow ICRI and ACI guidelines, common concrete <br />practices, and other applicable industry standards. Aquafin personnel or <br />representatives are not site inspectors or construction project managers <br />and therefore do not approve surface preparation, mixing, or application <br />of Aquafin products. Site visits by Aquafin personnel or representatives <br />are solely for the purpose of making technical recommendations, not for <br />providing supervision or quality control. <br />General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time of <br />printing. Depending on specific applications, in particular regarding <br />substrates, processing and environmental conditions may affect final results.</p> <p>LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period <br />of one year from the date of installation to be manufactured free of defects <br />and to be consistent with its technical properties as stated in our current <br />Technical Data Sheet. This product must be used as directed and within its <br />stated shelf life. AQUAFIN, INC. will replace or at our discretion refund the <br />purchase price of any product, excluding cost of labor, which is proven to be <br />defective. Our product recommendations are based on industry standards <br />and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or <br />use of the product. We do not guarantee compatibility of Aquafin products <br />with other brands. For this reason, we strongly recommend application of a <br />sample area at the jobsite to help determine suitability with other products. <br />AQUAFIN, INC. MAKES NO WARRANTY AS TO MERCHANTABILITY <br />OR FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN <br />LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. AQUAFIN, <br />INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. Any claim for a defective <br />product must be filed within 30 days of discovery of a problem, and must be <br />submitted with written proof of purchase. <br />For Professional Use Only.</p> <p>Safety: <br />Refer to Safety Data Sheet (SDS). This product contains portland <br />cement and sand (crystalline silica) and is highly alkaline (irritant) in contact <br />with water. Avoid breathing dust. May cause delayed lung injury (silicosis). <br />Use rubber gloves and goggles during mixing and application. Protect <br />skin and eyes. After contact with skin, wash with plenty of water. In case of <br />eye contact, rinse immediately with plenty of cool water and seek medical <br />advice.</p> <p>Certified to</p> <p>NSF/ANSI/CAN Standard 61 <br />see www.wqa.org for use restrictions</p> <p>MORTAR-LN Consumption & Yield of 50 lb (22.7 kg) bag <br />Resurface <br />and Parge Coat</p> <p>Application <br />Thickness</p> <p>Application Rate <br />(Dry Powder)</p> <p>inch</p> <p>mm</p> <p>1/8”</p> <p>3.2</p> <p>1/4”</p> <p>6.4</p> <p>5/16” <br />3/8”</p> <p>kg/m²</p> <p>lb/yd²</p> <p>1.25</p> <p>6.1</p> <p>2.50</p> <p>12.2</p> <p>8</p> <p>3.13</p> <p>9.5</p> <p>3.85</p> <p>1/2”</p> <p>12.7</p> <p>1”</p> <p>25.4</p> <p>Patch and Repair</p> <p>Approx. Volume Yield in Cubic Ft:</p> <p>Linear Applications</p> <p>Application Type</p> <p>lb/ft²</p> <p>kg/m²</p> <p>ft2</p> <p>m2</p> <p>11.3</p> <p>6.1</p> <p>40</p> <p>3.7</p> <p>22.5</p> <p>12.2</p> <p>20</p> <p>1.9</p> <p>15.3</p> <p>28</p> <p>15.3</p> <p>16</p> <p>1.5</p> <p>18.8</p> <p>34.7</p> <p>18.8</p> <p>13</p> <p>1.2</p> <p>5.00</p> <p>24.4</p> <p>45</p> <p>24.4</p> <p>10</p> <p>0.9</p> <p>10.0</p> <p>48.8</p> <p>90</p> <p>48.8</p> <p>5</p> <p>0.5</p> <p>0.42 ft3 (0.012 m3)</p> <p>Size <br />inch</p> <p>Approx. Yield <br />per Bag</p> <p>Application Rate <br />(Dry Powder) <br />lb/linear ft</p> <p>kg/linear m</p> <p>linear ft</p> <p>linear m</p> <p>Triangular Cant/Cove <br />Strips</p> <p>1.5” x 1.5”</p> <p>3.8 cm x 3.8 cm</p> <p>0.94</p> <p>1.4</p> <p>53</p> <p>16</p> <p>2” x 2”</p> <p>5.1 cm x 5.1 cm</p> <p>1.66</p> <p>2.5</p> <p>30</p> <p>9</p> <p>Reglets/Keyways</p> <p>1” x 1”</p> <p>2.5 cm x 2.5 cm</p> <p>0.83</p> <p>1.2</p> <p>60</p> <p>18.3</p> <p>2” x 2”</p> <p>5.1 cm x 5.1 cm</p> <p>3.33</p> <p>5.0</p> <p>15</p> <p>4.5</p> <p>1” x 1”</p> <p>2.5 cm x 2.5 cm</p> <p>0.83</p> <p>1.2</p> <p>60</p> <p>18.3</p> <p>U-shaped Routed <br />Cracks</p> <p>cm</p> <p>Approx. Yield <br />per Bag</p> <p>Notes: Application rates and yield values are approximate. Actual coverage may vary due to substrate and surface profile. <br />Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 4 of 4 <br />www.aquafin.net <br />(05/18/26-EK,AC)</p>
