505 Blue Ball Rd. #160
Elkton, MD 21921
Nonsag, corrosion inhibitor enhanced, vertical and overhead concrete repair mortar
CSI Div. 03
03 0130.71 Rehabilitation of Cast-in-place-concrete
MR Credit 5.1, Regional Materials..........................Up to 2 Points
IEQ Credit 4.2, L ow-Emitting Materials Paints and Coatings...1 Point
Flame Spread: 0
Fuel Contribution: 0
Smoke Development: 0
Using this AQUAFIN product can help contribute to LEED certification of projects in the
categories shown above.
MORTAR-V/O CI is a one component, lightweight, fiber reinforced,
polymer modified, high strength vertical and overhead everyday concrete
repair mortar. It can be placed in lifts up to 2” without forming. Its
formulation is designed for excellent workability and allows shaving after
reaching inital set for superior finishing. Additionally, MORTAR-V/O CI is
enhanced with a migrating corrosion inhibitor which helps protect localized
and adjacent reinforcing steel.
• Repairing vertical and overhead, indoor and outdoor, concrete,
masonry and brick substrates.
• Spalls or holes in concrete
• Deteriorated edges
• Very low sag - excellent “hang” characteristics
• Bonds very well to concrete, masonry & block
• Low shrinkage
• One component - just add water
• Excellent workability - can be sculpted and shaved with ease
• Enhanced with a migrating corrosion inhibitor to help protect localized
and adjacent reinforcing steel.
• Concrete surfaces must be structurally sound, free of any loose or
deteriorated concrete, dirt, dust, grease, oil, sealers, curing compounds
and all other bond-inhibiting materials.
• Mechanically prepare surfaces to achieve a surface profile equal
to CSP 5-7 as per ICRI Guideline No. 310.2R-13, Selecting and
Specifying Concrete Surface Preparation for Sealers, Coatings, Polymer
Overlays, and Concrete Repair.
• Properly clean profiled area by water-blasting. All surfaces must be
saturated surface dry (SSD) but with no standing water, immediately
prior to application.
• Only proceed with application when the temperatures remain between
40°F and 90°F (4°C and 32°C) and protect from freezing for
24 hours after application. For temperatures above 85°F (29°C),
follow ACI hot-weather application guidelines to ensure a successful
• All exposed steel reinforcement must be cleaned to a white metal finish
and primed with an anti-corrosion coating.
Check our website for the latest version of the Technical Datasheet.
MORTAR-V/O CI mixed
Mix ratio (water:powder)
1.2 - 1.25 gal water : 50 lb powder
(4.5 - 4.7 L water : 22.7 kg powder)
Application temp. range
40°F to 90°F (4°C to 32°C)
~10 - 12 minutes
Physical Properties: The values stated are applicable with ambient
temperatures of 73°F (23°C) and 50% relative air humidity. Higher temperatures
shorten the processing time, lower temperatures extend processing times.
~1,000 psi after 3 hours
~2,500 psi after 24 hours
~3,500 psi after 7 days
~4,500 psi after 28 days
Flexural Strength ASTM C-348
Length Change ASTM C-157
0.086% @ 28 day wet cure
Bond Strength ASTM C-882M
1,750 psi @ 28 days
Cool and dry, 12 months in original sealed
50 lb bags (22.7 kg)
Approximate Yield per 50 lb Bag: ~0.42 ft3 / 50 lb bag
• Repair areas should have saw-cut straight edges with a minimum of
1/4” (6 mm) depth (avoid featheredging).
Mixing Ratio: 1.2 - 1.25 gal water : 50 lb powder
• Precondition MORTAR-V/O CI to ~70°F (21°C) prior to mixing.
• For best results, mechanically mix at slow speed with a 3/4” drill and
mixing paddle. Hand mix for small repairs.
• Add the required amount of potable water into a clean mixing bucket.
Gradually add powder 1/3 at a time while mixing continuously.
• Mix at slow speeds to prevent entraining air for a min. of 3 minutes until
a lump-free consistency is achieved.
• Working time is ~10 – 12 minutes at 70° F
DO NOT OVERWATER! If too much water is added, the mixture tends
to segregate resulting in uneven surface strengths. Surfaces with reduced
strength must be removed mechanically.
Page 1 of 2
Read all instructions thoroughly prior to installation. Ensure substrate and
ambient temperatures are between 40°F and 90°F (4°C and 32°C)
1. Scrub a small amount of mixed MORTAR-V/O CI into the SSD substrate.
Work material into the entire substrate and cavity to promote proper
2. Place MORTAR-V/O CI into the wet scrub coat before it dries, keying in
and compact thoroughly.
3. Apply material in lifts of 1/4 – 2“ (6 – 51 mm). Avoid featheredging.
For optimum mechanical bond on successive lifts, thoroughly score each
lift and allow to reach initial set before the next layer is applied.
4. Trowel material to the desired finish. MORTAR-V/O CI can be shaved
after material has reached initial set for further finishing.
Damp cure for 3 days. Begin curing as soon as the patch has set by
keeping surface moist as per ACI recommendations for Portland cement
concrete, using burlap, polyethylene or a fine mist of water. If this is not
practicable, coat with an approved water based curing compound,
(contact Aquafin Technical Department for approved products). However,
curing compound may adversely affect following lifts of mortar, leveling
mortar or protective coatings.
• Do not bridge moving cracks or joints.
• Do not add admixtures or extend with aggregate.
• Protect from freezing for 24 hours after application.
Promptly wash hands and tools with water before material hardens. Cured
material must be removed mechanically.
Refer to SDS. This product contains portland cement and sand
(crystalline silica) and is highly alkaline (irritant) in contact with water. Avoid
breathing dust. May cause delayed lung injury (silicosis). Use rubber
gloves and goggles during mixing and application. Protect skin and eyes.
After contact with skin, wash with plenty of water. In case of eye contact,
rinse immediately with plenty of cool water and seek medical advice.
KEEP OUT OF REACH OF CHILDREN.
LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a
period of one year from the date of installation to be manufactured free
of defects and to be consistent with its technical properties as stated in our
current Technical Data Sheet. This product must be used as directed and
within its stated shelf life. AQUAFIN INC. will replace or at our discretion
refund the purchase price of any product, excluding cost of labor, which
is proven to be defective. Our product recommendations are based on
industry standards and testing procedures. It is the buyer’s obligation to
test the suitability of the product for an intended use prior to using it. We
assume no warranties written, expressed or implied as to any specific
methods of application or use of the product. AQUAFIN INC. MAKES
NO WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable
for damages of any sort including remote or consequential damages, down
time, or delay. Any claim for a defectiveproduct must be filed within 30
days of discovery of a problem, and must be submitted with written proof of
For Professional Use Only.
12 months in unopened, dry, undamaged bags.
Installer is responsible for proper product application. Site visits by Aquafin
personnel or representatives are solely for the purpose of making technical
recommendations, not for providing supervision or quality control.
Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact
our technical department for further information before starting any applications.
Page 2 of 2