18 PRO-Tekt Flexcoat_060920.pdf
2 Pages
419 KB
Download
<h1>18 PRO-Tekt Flexcoat_060920.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>PRO-Tekt Flexcoat</p> <p>100% solids, waterproof, hybrid polyurea/polyurethane base coat. <br />CSI Div. 07 <br />07 18 00 Traffic Coatings</p> <p>Physical and Technical Data <br />Tensile Strength ASTM D412</p> <p>1,450 psi</p> <p>LEED Points</p> <p>Elongation ASTM D412</p> <p>500 - 600%</p> <p>MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, L ow-Emitting Materials Paints and Coatings...1 Point</p> <p>Density DIN 53479</p> <p>1.05 gm/ml</p> <p>Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Percent Solids</p> <p>100%</p> <p>VOC</p> <p>0 gm/l</p> <p>Product Description: <br />PRO-Tekt Flexcoat is the base coat in the PRO-Tekt Traffic Deck System. It <br />is a 2-component, solvent free, hybrid polyurea/polyurethane base coat, <br />designed to be used in combination with the Trafficoat intermediate coat to <br />provide a fully elastomeric traffic system for concrete structures.</p> <p>Shore A ASTM D2240</p> <p>70</p> <p>Tear ASTM D624C</p> <p>215 lbs/inch</p> <p>Elcometer Adhesion ASTM D4541</p> <p>>435 psi on Primer</p> <p>Pot Life*</p> <p>15 minutes</p> <p>Gel Time*</p> <p>15 - 20 minutes</p> <p>Tack Free Time*</p> <p>40 - 50 minutes</p> <p>The PRO-Tekt Traffic Deck System consists of the following components: <br />1. Primer: VAPORTIGHT COAT-SG2 or SG4 <br />2. Base Coat: PRO-Tekt Flexcoat <br />3. Intermediate Coat: PRO-Tekt Trafficoat <br />4. Top Coat: PRO-Tekt Topcoat PA <br />Typical Applications: <br />• Use as the waterproof, elastomeric membrane of the PRO-Tekt Traffic <br />Deck system for pedestrian bridges, roof decks, parking decks and <br />ramps. <br />Advantages: <br />• Low odor during application and cure. <br />• Excellent crack-bridging properties and flexibility. <br />• High tensile strength <br />• High elongation <br />• Excellent adhesion <br />• Rapid cure/recoat times. <br />Site Mock-up: <br />• Aquafin recommends installation of a field sample of min. 100 ft2 at <br />the project site or other pre-selected area as agreed to by owner’s <br />representative, applicator and manufacturer. <br />• Apply materials in accordance with manufacturer’s written application <br />instructions. <br />• Field sample will be standard for judging color and texture on remainder <br />of project. <br />• Maintain field sample during construction for workmanship comparison. <br />• Do not alter, move, or destroy field sample until work is completed and <br />approved by Owner’s representative. <br />Substrate Preparation: <br />• Surfaces must be properly primed with Aquafin VAPORTIGHT COAT <br />SG2 or SG4 (Check SG2 or SG4 data sheets for application <br />instructions and coverage rates). All surfaces must be dry, free from <br />loose sand, dirt, dust and other foreign substances that could interfere <br />with adhesion to the prime coat. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>*100 gm mixed sample at 77°F (25˚C)</p> <p>Full service use</p> <p>Overcoat @ 4 hours</p> <p>Theoretical Coverage: note product <br />waste and substrate variances will <br />affect coverage rates</p> <p>170 ft2/Kit @ 40 wet mils <br />40 ft2/gallon @ 40 wet mils</p> <p>• Only proceed with application when ambient temperature is minimum <br />40°F (4°C) and rising, to maximum 95°F (35°C), and more than 6° <br />above dew point. Temperatures must be maintained within this range for <br />at least 24 hours after the installation of the primer. Do NOT proceed <br />with application when the temperatures drop below 40°F (4°C) or if <br />precipitation is imminent. Special precautions are to be taken when <br />ambient and/or substrate temperatures are approaching, at, or above <br />95°F (35°C). It may be necessary to limit material application to <br />evening hours for exterior exposed decks. <br />• Expansion and control joints are to be prepared in accordance with <br />project specifications. <br />Mixing: <br />PRO-Tekt Flexcoat is supplied in the appropriate mixing ratio. Always mix <br />full units. <br />• Use Use chemical resistant (Nitrile) gloves and goggles when mixing or <br />applying PRO-Tekt Flexcoat. <br />• Material should be between 60°F (15°C) and 85°F (29°C) at time <br />of mixing. <br />1. Open each container carefully. Do not spill material. <br />2. Pre-mix Component A for 30 seconds, then pour into Component B. <br />3. Mix material using a jiffy style paddle vigorously (high speed) for 45 - 60 <br />seconds while scraping down the sides of the pail until a homogeneous <br />color is achieved. <br />NOTE: Extended mixing times can result in premature gel times.</p> <p>Page 1 of 2</p> <p>(06/09/20-EKVB)</p> <p>PRO-Tekt Flexcoat <br />Application: <br />• Pour PRO-Tekt Flexcoat onto substrate in sufficient quantity and uniformly <br />distribute with a 1/8” notched squeegee. <br />• Apply PRO-Tekt Flexcoat at 40 wet mils thickness for parking stalls, <br />driving lanes, ramps and turning circles. <br />• Allow PRO-Tekt Flexcoat to cure a minimum of 4 hours. Intermediate <br />coat (PRO-Tekt Trafficoat) must be applied within 24 hours after cure. <br />Curing <br />• PRO-Tekt Flexcoat is self-curing. <br />• Environmental conditions may accelerate or slow down curing times. <br />Clean-up <br />Promptly wash hands and tools with an approved solvent before material <br />hardens. Cured material must be removed mechanically. <br />Limitations <br />• Substrate and ambient temperatures must be above 40°F (4°C) and at <br />least 6° above the dew point. <br />• Precondition material between 60°F (15°C) and 85°F (29°C) prior <br />to time of mixing. Temperature can affect cure times. PRO-Tekt Flexcoat <br />cures faster when applied during warm weather and high humidity <br />conditions and slower during cool temperatures and low humidity <br />conditions. <br />• Discontinue application if substrate exceeds 95°F (35°C) <br />• Provide for expansion and control joints where specified. Never bridge <br />expansion joints, always ensure such joints are honored completely <br />through entire PRO-Tekt Traffic Deck System. Where control or expansion <br />joints do not exist in the substrate, provide for them in the system per <br />design professionals recommendations. <br />• Do not mix more material than can be placed in 15 - 20 minutes.</p> <p>Packaging and Shelf Life: <br />Shelf life is 1 year in closed, original packaging, stored in a dry, cool <br />place, above 50°F (10°C) and below 85°F (30°C). <br />• 37.5 lbs/17.0 kg Kit (4.3 Gallon/16.3 Liter) <br /> Comp A: 6.25 lbs (2.8 KG) <br /> Comp B: 31.25 lbs. (14.2 KG) <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed or implied as to any specific methods of application or use of the product. <br />AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Page 2 of 2</p> <p>(06/09/20-EKVB)</p>
