TDS-PRO-Tekt Joint Sealant_092922.pdf
2 Pages
419 KB
Download
<h1>TDS-PRO-Tekt Joint Sealant_092922.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>PRO-Tekt Joint Sealant</p> <p>Two-Component, Non-Sag, Flexible, Polyurethane Joint Sealant <br />CSI Div. 07 <br />07 14 16 Cold Fluid Applied Waterproofing <br />07 18 00 Traffic Coatings <br />07 18 13 Pedestrian Traffic Coatings <br />07 18 16 Vehicular Traffic Coatings <br />LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of <br />projects in the categories shown above. <br />Product Description: <br />PRO-Tekt Joint Sealant is a two-component, high solids, non-sag, flexible, <br />polyurethane joint sealant. The non-sag formula makes it ideal for <br />applications on vertical cracks and joints. PRO-Tekt Joint Sealant is also an <br />excellent choice for horizontal crack and joint pre-treatment of concrete <br />before the application of an Aquafin polyurethane coating system. <br />Typical Applications: <br />• Warehouses, loading docks, manufacturing, and industrial facilities <br />• Bridge headers, airports, and parking garage decks <br />Advantages: <br />• Superb performance <br />• Excellent flexibility <br />• Low VOC’s <br />Preparation: <br />• All areas of concrete to be treated must be free from loose sand, dirt, <br />dust, oil, grease, sealers, paint, existing coatings, and other foreign <br />substances that could interfere with adhesion. <br />• Concrete must be at least 28 days old and must have reached a <br />minimum 3,000 psi (20 MPa) compressive strength. <br />• Crack and joint edges must be at a straight 90° angle to the horizontal <br />plane of the concrete slab. Chase all cracks to a depth of at least 2” <br />(5.08 cm). <br />• Joints must be cut according to ACI recommendations. <br />• When repairing T-joints, cut joint to a depth of at least 25% of the total <br />depth of the slab. The side of the T-joint must be cut 12” (20.4 cm) from <br />the joint and a minimum of 2” (5.08 cm) deep. <br />• Flush cracks and joints clean using an appropriate cleaning solution and <br />rinse well. Use clean, oil free, compressed air to blow out any remaining <br />dust, water, or debris prior to installation. <br />• The inside area of all cracks and joints must be primed with PRO-Tekt <br />SP (Sealant Primer) prior to the application of PRO-Tekt Joint Sealant. <br />Refer to the current PRO-Tekt SP (Sealant Primer) Technical Data Sheet <br />for all application instructions, including surface preparation, etc. <br />• Ensure PRO-Tekt Joint Sealant is applied to primed surfaces within the <br />required recoat times. <br />• Primed surfaces must be completely dry and clean. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Physical and Technical Data <br />Mixing Ratio</p> <p>1 Part-A: 3 Part-B</p> <p>Pot Life <br />@ 75°F (24°C) & 50% RH</p> <p>25 min (± 5 min)</p> <p>Tack-Free Time <br />@ 77°F (25°C) & 50% RH</p> <p>12 - 24 hrs</p> <p>Cure Time at 75°F (24°C), <br />Light Pedestrian Traffic <br />Light Vehicle Traffic</p> <p>minimum 48 hrs <br />mimimum 7 days</p> <p>Specific Gravity <br />Side-A <br />Side-B</p> <p>1.06 ± 0.1 <br />1.26 ± 0.1</p> <p>Viscosity at 75°F (24°C) <br />Side-A <br />Side-B</p> <p>50 ± 20 poise <br />thixotrope</p> <p>Total Solids by Weight, <br />(ASTM D2369)</p> <p>95 ± 2%</p> <p>Total Solids by Volume, <br />(ASTM D2697)</p> <p>94 ± 2%</p> <p>Hardness, <br />(ASTM D2240)</p> <p>40 ± 5 Shore A</p> <p>Tensile Strength, <br />(ASTM D412)</p> <p>300 ± 50 psi <br />(2.1 ± 0.3 MPa)</p> <p>Elongation, <br />(ASTM D412)</p> <p>500 ± 50%</p> <p>Tear Strength, <br />(ASTM D624)</p> <p>50 ± 5 pli <br />8.8 ± 0.8 kNm</p> <p>Color</p> <p>Gray</p> <p>VOC Content</p> <p>0.42 lb/gal <br />50 g/L</p> <p>All data are averages of several tests under laboratory conditions. In practice <br />climatic variations such as temperature, humidity, and porosity of substrate may <br />affect these values</p> <p>• Substrate and ambient temperatures must be between 40°F to 135°F <br />(4.4°C to 57°C). <br />Mixing: <br />Condition all components 75°F to 80°F (24°C to 27°C) prior to mixing. <br />The volume mixing ratio is 1 part component A to 3 parts component B <br />(1A:3B). Carefully mix each part individually and then accurately measure <br />out the correct volumes of component A and component B before <br />combining together. Mix for at least 5 minutes using a low speed drill <br />with a jiffy mixing blade or paddle. Occasionally scrape the sides of the <br />Page 1 of 2</p> <p>(updated 09/29/22-EKAC)</p> <p>PRO-Tekt Joint Sealant <br />container while mixing. For best results, mix at slow speeds (300 – 500 <br />rpm) to prevent entraining air, and continue until a homogeneous mixture is <br />achieved. Do not mix in an up and down motion. <br />Installation: <br />Read all instructions thoroughly prior to installation. <br />Apply PRO-Tekt Joint Sealant with a caulking gun, or by pouring material <br />directly into the joint. Fill joints from the bottom up. <br />• Control Joints: Use a closed cell backer rod in all control <br />joints. Depth should not be more than 25% of the total slab <br />thickness. Apply PRO-Tekt Joint Sealant over the installed <br />backer rod. <br />• Construction Joints: Do not use backer rod or sand. Fill all <br />construction joints to full depth thickness with PRO-Tekt Joint <br />Sealant. <br />• Cracks: Fill all cracks flush with PRO-Tekt Joint Sealant. <br />Tool and finish joints and cracks according to project drawings and <br />specifications. <br />Curing and Protection: Allow time for product to cure before opening <br />to light pedestrian traffic. Cure time will vary depending on temperature <br />and humidity. Typically, 48 hours based on 75°F (24°C) & 50% RH.</p> <p>Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Packaging: <br />1.5 gallon kit (5.67 L) <br />Component A: (1) 1/2 gal can [net fill 0.375 gal (1.42 L)] <br />Component B: (1) 2 gal pail [net fill 1.125 gal (4.25 L)] <br />Storage and Shelf Life: <br />Shelf Life: 1 year in original unopened container. <br />Storage: Indoors at 60°F to 90°F (15.5°C to 32°C) in dry and dark <br />conditions. Protect from moisture. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />PLEASE NOTE: To be eligible for a warranty, cracks and joints must be primed with <br />PRO-Tekt SP (Sealant Primer) prior to the application of PRO-Tekt Joint Sealant.</p> <p>Clean-up: <br />TOOLS & EQUIPMENT: Remove fresh/uncured material with an <br />approved solvent. Cured material can only be removed mechanically. <br />MATERIAL: Dispose of in accordance with local, state and federal <br />disposal regulations. <br />Limitations: <br />• Do not dilute or thin product. <br />• The physical properties of PRO-Tekt Joint Sealant are UV stable. <br />However, discoloration will occur in direct sunlight. <br />• Do not use PRO-Tekt Joint Sealant in submerged applications. Ensure <br />that there is proper drainage in all areas where PRO-Tekt Joint Sealant <br />is used. <br />• Contact Aquafin Technical Department for use in areas not listed. <br />• Do not mix more than can be used in 20 mins [based on 75°F (24°C) <br />& 50% RH]. <br />• Curing time will vary, depending on surface and air temperatures. <br />Cold temperatures and low humidity will extend the curing time. High <br />temperatures and high humidity will shorten the curing time. <br />• Consult Aquafin Technical Department when mixing or placing outside <br />of the temperature recommendations listed.</p> <p>LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed or implied as to any specific methods of application or use of the product. <br />In addition, no warranty or guarantee is being issued with respect to appearance, <br />color, fading, chalking, staining, shrinkage, peeling, normal wear and tear, damage <br />caused by abuse, neglect and lack of proper maintenance, acts of nature and/or <br />physical movement of the substrate or structural defects. AQUAFIN INC. MAKES <br />NO WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR <br />PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES <br />EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort <br />including remote or consequential damages, down time, or delay. Any claim for a <br />defective product must be filed within 30 days of discovery of a problem, and must be <br />submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>PRO-Tekt Joint Sealant Coverage Chart <br />Coverage data is based on linear feet measurements.</p> <p>Width of Joint <br />Depth <br />of <br />Joint</p> <p>1/4”</p> <p>1/4”</p> <p>3/8”</p> <p>1/2”</p> <p>5/8”</p> <p>3/4”</p> <p>7/8”</p> <p>1”</p> <p>308</p> <p>205</p> <p>154</p> <p>123</p> <p>102</p> <p>88</p> <p>77</p> <p>3/8”</p> <p>205</p> <p>136</p> <p>102</p> <p>82</p> <p>68</p> <p>58</p> <p>51</p> <p>1/2”</p> <p>154</p> <p>102</p> <p>77</p> <p>61</p> <p>51</p> <p>44</p> <p>38</p> <p>5/8”</p> <p>123</p> <p>82</p> <p>61</p> <p>49</p> <p>41</p> <p>35</p> <p>30</p> <p>3/4”</p> <p>102</p> <p>68</p> <p>51</p> <p>41</p> <p>34</p> <p>29</p> <p>25</p> <p>7/8”</p> <p>88</p> <p>58</p> <p>44</p> <p>36</p> <p>29</p> <p>25</p> <p>22</p> <p>1”</p> <p>77</p> <p>51</p> <p>38</p> <p>30</p> <p>25</p> <p>22</p> <p>19</p> <p>Note: Coverage is approximate and will vary depending on jobsite conditions. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Page 2 of 2</p> <p>(updated 09/29/22-EKAC)</p>
