PRO-Tekt Topcoat-PA_073020.pdf
2 Pages
418 KB
Download
<h1>PRO-Tekt Topcoat-PA_073020.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>PRO-Tekt Topcoat PA</p> <p>100% solids, high performance, aliphatic polyaspartic polyurea top coat <br />CSI Div. 07 <br />07 18 00 Traffic Coatings</p> <p>Physical and Technical Data <br />Tensile Strength ASTM D412</p> <p>5,630 psi</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, L ow-Emitting Materials Paints and Coatings...1 Point</p> <p>Elongation ASTM D412</p> <p>10%</p> <p>Density</p> <p>1.08 g/cc</p> <p>Using this AQUAFIN product can help contribute to LEED certification of projects in the</p> <p>Percent Solids</p> <p>100%</p> <p>categories shown above.</p> <p>VOC</p> <p>0 g/l</p> <p>Product Description: <br />PRO-Tekt Topcoat PA is a solvent-free, 100% solids, 2-component, aliphatic, <br />polyaspartic, polyurea coating designed to withstand pedestrian and <br />vehicular traffic. It is used as the topcoat in the Pro-Tekt Traffic Deck <br />System.</p> <p>Shore D ASTM D2240</p> <p>75 - 80</p> <p>Tear ASTM D624C</p> <p>803 pli</p> <p>Taber Abrasion ASTM D3389</p> <p>12/1000 mg/rev. loss</p> <p>Pot Life*</p> <p>5 -10 minutes</p> <p>Gel Time*</p> <p>10 -15 minutes</p> <p>Tack Free Time*</p> <p>30 - 45 minutes</p> <p>The PRO-Tekt Traffic Deck System consists of the following components: <br />1. Primer: VAPORTIGHT COAT-SG2 or SG4 <br />2. Base Coat: PRO-Tekt Flexcoat <br />3. Intermediate Coat: PRO-Tekt Trafficoat <br />4. Top Coat: PRO-Tekt Topcoat PA <br />Typical Applications: <br />Used as the topcoat in the PRO-Tekt Traffic Deck System on pedestrian <br />plaza decks, pedestrian bridges, roof decks, parking decks, and ramps. <br />Advantages: <br />• Low odor during application and cure. <br />• Quick return to service. <br />• UV stable. <br />• High abrasion resistance. <br />• Zero VOC’s. <br />Site Mock-up: <br />• Aquafin recommends installation of a field sample of min. 100 ft2 at <br />the project site or other pre-selected area as agreed to by owner’s <br />representative, applicator and manufacturer. <br />• Apply materials in accordance with manufacturer’s written application <br />instructions. <br />• Field sample will be standard for judging color and texture on remainder <br />of project. <br />• Maintain field sample during construction for workmanship comparison. <br />• Do not alter, move, or destroy field sample until work is completed and <br />approved by Owner’s representative. <br />Substrate Preparation: <br />• Apply only onto properly installed Aquafin Primer or PRO-Tekt <br />Intermediate Coat broadcast with aggregate (refer to appropriate <br />product TDS for application instructions and coverage rates). Ensure all <br />surfaces are dry, free from dirt, dust and other foreign substances. <br />• Only proceed with application when ambient temperature is minimum <br />40°F (4°C) and rising to maximum 85°F (30°C), and more than 6° <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>*100 gm mixed sample at 77°F (25˚C)</p> <p>Full service use</p> <p>4 hours</p> <p>Theoretical Coverage: note product <br />waste and substrate variances will <br />affect coverage rates</p> <p>275 - 290 ft2 @ 21—25 wet mils. <br />Coverage will vary based on <br />aggregate load and amplitude.</p> <p>degrees above dew point. Temperatures must be maintained within this <br />range for at least 24 hours after the installation of PRO-Tekt Topcoat <br />PA. Do NOT proceed with application when the temperatures drop <br />below 40°F (4°C) or if precipitation is imminent. Special precautions <br />are to be taken when ambient and/or substrate temperatures are <br />approaching, at, or above 95°F (35°C) and it may be necessary to <br />limit material application to evening hours for exterior exposed decks. <br />• Expansion and control joints are to be prepared in accordance with <br />project specifications. <br />Mixing: <br />PRO-Tekt Topcoat PA is supplied in the appropriate mixing ratio. Always <br />mix full units. <br />• Use chemical resistant Nitrile gloves and goggles when mixing or <br />applying PRO-Tekt Topcoat PA. <br />• Material should be between 60°F (15°C) and 85°F (29°C) at time of <br />mixing. <br />1. P re-mix Component A for 30 secs until uniform in color. <br />2. Open each container carefully. Do not spill material. <br />3. Pour all contents of Component B into Component A (packaged in the <br />larger 5-gal pail). <br />4. Mix material using a jiffy style paddle at low speed for a minimum 60 <br />seconds until a uniform homogenous color is achieved <br />5. Thoroughly scrape sides of pail as material is placed in a clean <br />secondary container. Mix for an additional 15- 20 seconds. <br />NOTE: Extended mixing times can result in premature gel times.</p> <p>Page 1 of 2</p> <p>(07/30/20-EKVB)</p> <p>PRO-Tekt Topcoat PA <br />Application: <br />PRO-Tekt Topcoat should be applied to properly applied PRO-Tekt <br />Trafficoat after a minimum of 4 hours and a maximum of 48 hours. <br />• Immediately after mixing, pour PRO-Tekt Topcoat in sufficient quantity <br />onto surface and uniformly distribute with a 1/8” notched squeegee. <br />• Apply PRO-Tekt Topcoat at 66 — 70 sq ft /gal @ 21-25 wet mils (rate <br />will vary based upon aggregate load and amplitude) <br />• Follow with a 1/4” - 3/8” non-shed roller, back rolling at right angle <br />(90 degrees) to the squeegee application to achieve uniform coverage. <br />Curing: <br />• PRO-Tekt Topcoat PA is self-curing. <br />• Environmental conditions may accelerate or slow down curing times. <br />Clean-up: <br />Promptly wash hands and tools with an approved solvent before material <br />hardens. Cured material must be removed mechanically. <br />Limitations: <br />• Do not store materials outdoors exposed to sunlight for prolonged <br />periods. <br />• Excessive sun exposure should be avoided during application. <br />• Provide for expansion and control joints where specified. Never bridge <br />expansion joints, always ensure such joints are honored completely <br />through entire PRO-Tekt Traffic Deck System. Where control or <br />expansion joints do not exist in the substrate, provide for them in the <br />system per design professionals’ recommendations.</p> <p>Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear Nitrile gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Datasheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN, INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed or implied as to any specific methods of application or use of the product. <br />AQUAFIN, INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of <br />a problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Packaging and Shelf Life: <br />Shelf life is 12 months in closed, original packaging, stored in a dry, cool <br />place, above 50°F (10°C) and below 85°F (30°C). <br />• 38.24 lbs/17.35 kg Kit (4.2 gallon/15.9 Liter) <br />Comp A: 19.12 lbs (8.67 kg) <br />Comp B: 19.12 lbs (8.67 kg)</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Page 2 of 2</p> <p>(07/30/20-EKVB)</p>
