PRO-Tekt Trafficoat_052621.pdf
2 Pages
417 KB
Download
<h1>PRO-Tekt Trafficoat_052621.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>PRO-Tekt Trafficoat</p> <p>100% solids, rapid curing, polyurethane intermediate coat <br />CSI Div. 07 <br />07 18 00 Traffic Coatings</p> <p>Physical and Technical Data <br />Tensile Strength ASTM D412</p> <p>3,100 psi</p> <p>LEED Points:</p> <p>Elongation ASTM D412</p> <p>60 %</p> <p>Density DIN 53479</p> <p>1.01 g/cc</p> <p>Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Percent Solids</p> <p>100%</p> <p>VOC</p> <p>0 g/l</p> <p>Product Description: <br />Pro-Tekt Trafficoat is a 2-component, polyurethane, intermediate coat <br />designed to provide a durable, anti-slip surface. It can be used in <br />conjunction with various size aggregate depending on the level of traffic <br />anticipated. PRO-Tekt Trafficoat is designed to be used in combination with <br />the PRO-Tekt Flexcoat and Pro-Tekt Topcoat PA waterproof membrane to <br />provide a fully elastomeric traffic system for concrete structures.</p> <p>Shore D ASTM D2240</p> <p>60 - 65</p> <p>Tear ASTM D624C</p> <p>566 pli</p> <p>Taber Abrasion ASTM D3389</p> <p>125/1000 mg/rev. loss</p> <p>Elcometer Adhesion ASTM D4541</p> <p>>435 psi</p> <p>Moisture Vapor Transmission Permatron W</p> <p>0.96 perms</p> <p>Pot Life*</p> <p>15 minutes</p> <p>The PRO-Tekt Traffic Deck System consists of the following components: <br />1. Primer: VAPORTIGHT COAT-SG2 or SG4 <br />2. Base Coat: PRO-Tekt Flexcoat <br />3. Intermediate Coat: PRO-Tekt Trafficoat <br />4. Top Coat: PRO-Tekt Topcoat PA</p> <p>Gel Time*</p> <p>15 - 20 minutes</p> <p>Tack Free Time*</p> <p>60 - 70 minutes</p> <p>MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, L ow-Emitting Materials Paints and Coatings...1 Point</p> <p>Typical Applications: <br />• Used as the intermediate coat in the PRO-Tekt Traffic Deck System for <br />binding aggregate on pedestrian plaza decks, pedestrian bridges, roof <br />decks, parking decks, and ramps. <br />Advantages: <br />• Low odor during application and cure. <br />• Excellent flexibility. <br />• Can be used in conjunction with a wide range of aggregates <br />depending upon the type and level of traffic anticipated. <br />• Rapid cure times compared to epoxy systems. <br />• Able to fully cure in colder temperatures <br />Site Mock-up: <br />• Aquafin recommends installation of a field sample of min. 100 ft2 at <br />the project site or other pre-selected area as agreed to by owner’s <br />representative, applicator and manufacturer. <br />• Apply materials in accordance with manufacturer’s written application <br />instructions. <br />• Field sample will be standard for judging color and texture on remainder <br />of project. <br />• Maintain field sample during construction for workmanship comparison. <br />• Do not alter, move, or destroy field sample until work is completed and <br />approved by Owner’s representative. <br />Substrate Preparation: <br />• Apply only onto properly installed PRO-Tekt Traffic Deck System Base <br />Coat (refer to PRO-Tekt Flexcoat TDS for application instructions and <br />coverage rates). Ensure all surfaces are dry, free from dirt, dust and <br />other foreign substances. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>*100 gm mixed sample at 77 °F (25˚C) <br />Theoretical Coverage: note product waste and <br />substrate variances will affect coverage rates</p> <p>190 ft2 per kit @ 32 wet mils <br />45 ft2/gal @ 32 wet mils <br />40 ft2/gal @ 40 wet mils</p> <p>• Only proceed with application when ambient temperature is minimum <br />40°F (4°C) and rising, and more than 6°F above dew point. <br />Temperatures must be maintained within this range for at least 24 hours <br />after the installation of PRO-Tekt Intermediate Coat. Do NOT proceed <br />with application when the temperatures drop below 40°F (4°C) or if <br />precipitation is imminent. Special precautions are to be taken when <br />ambient and/or substrate temperatures are approaching, at, or above <br />95°F (35°C) and it may be necessary to limit material application to <br />evening hours for exterior exposed decks. <br />• Expansion and control joints are to be prepared in accordance with <br />project specifications. <br />Mixing: <br />PRO-Tekt Trafficoat is supplied in the appropriate mixing ratio. Always mix <br />full units. <br />• Use chemical resistant (Nitrile) gloves and goggles when mixing or <br />applying PRO-Tekt Trafficoat. <br />• Material should be between 60°F (15°C) and 85°F (29°C) at time of <br />mixing. <br />1. Pre-mix Component A for 30 secs until uniform in color. <br />2. Open each container carefully. Do not spill material. <br />3. Pour all contents of Component B into Component A (packaged in the <br />larger 5-gal pail). <br />4. Mix material using a jiffy style paddle at low speed for a minimum 60 <br />seconds until a uniform homogenous color is achieved. <br />5. Thoroughly scrape sides of pail as material is placed in a clean <br />secondary container. Mix for an additional 15- 20 seconds. <br />NOTE: Extended mixing times can result in premature gel times. <br />Page 1 of 2</p> <p>(05/26/21-EKVB)</p> <p>PRO-Tekt Trafficoat <br />Application: <br />• PRO-Tekt Trafficoat should be applied to properly applied PRO-Tekt <br />Flexcoat after a minimum of 4 hours and a maximum of 24 hours. <br />• Apply PRO-Tekt Trafficoat at the following thickness <br />- Parking Stalls and Driving Lanes: 45 ft2/gal @ 32 wet mils <br />- Ramps and Turning Circles: 35 ft2/gal @ 40 wet mils <br />• Immediately after mixing, pour PRO-Tekt Trafficoat in sufficient quantity <br />onto surface and uniformly distribute with a 1/8” notched squeegee. <br />• F ollow with a 3/8” or 1/2” non-shed synthetic roller, back rolling at <br />right angle (90 degrees) to the squeegee application to achieve uniform <br />coverage. <br />• Immediately (within 2 minutes) after application, broadcast clean, oven <br />dried #20 - 50 silica sand to rejection (full broadcast). The aggregate <br />should be applied vertically, allowing it to fall onto the PRO-Tekt <br />Trafficoat at a rate of approximately 30 - 50 lb./100 ft2 (1.5 kg/m2). <br />This will avoid any potential “rippling” in the finished surface. <br />• Allow PRO-Tekt Trafficoat to cure for a minimum 4 hours. PRO-Tekt <br />Topcoat must be applied after a minimum 4 hours and a maximum 48 <br />hours. <br />Curing: <br />• PRO-Tekt Trafficoat is self-curing. <br />• Environmental conditions may accelerate or slow down curing times. <br />Clean-up: <br />Promptly wash hands and tools with an approved solvent before material <br />hardens. Cured material must be removed mechanically. <br />Limitations: <br />• Do not store materials outdoors exposed to sunlight for prolonged <br />periods. Temperature can affect cure times. PRO-Tekt Trafficoat cures <br />faster when applied during warm weather and high humidity conditions <br />and slower during cool temperatures and low humidity conditions. <br />• Excessive sun exposure should be avoided during application. <br />• Provide for expansion and control joints where specified. Never bridge <br />expansion joints, always ensure such joints are honored completely <br />through entire PRO-Tekt Traffic Deck System. Where control or <br />expansion joints do not exist in the substrate, provide for them in the <br />system per design professionals’ recommendations.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Packaging and Shelf Life: <br />Shelf life is 1 year in closed, original packaging, stored in a dry, cool <br />place, above 50°F (10°C) and below 85°F (30°C). <br />• 38.25 lb/17.3 kg Kit (4.3 gallon/16.3 Liter) <br /> Comp A: 25.5 lbs (11.6 kg) <br /> Comp B: 12.75 lbs (5.8 kg) <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear nitrile gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Datasheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN, INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed or implied as to any specific methods of application or use of the product. <br />AQUAFIN, INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Page 2 of 2</p> <p>(05/26/21-EKVB)</p>
