RE-ROOF EPDM Treatment_121622.pdf
2 Pages
417 KB
Download
<h1>RE-ROOF EPDM Treatment_121622.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>RE-ROOF EPDM Treatment</p> <p>Single Component, Liquid Treatment for existing EPDM membranes <br />CSI Div. 07 & 09 <br />07 01 50 Maintenance of Membrane Roofing <br />07 01 50.61 Roof Re-Coating <br />07 14 16 Cold Fluid Applied Waterproofing <br />09 91 33 Primers <br />09 01 90 Maintenance of Painting and Coating</p> <p>Technical Properties:</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />RE-ROOF EPDM Treatment is a single-component, low viscosity, liquid <br />treatment that functions as a primer for existing EPDM membranes. REROOF EPDM Treatment is designed for use as part of Aquafin‘s RE-ROOF <br />System. The RE-ROOF System is an eco-friendly, reliable solution for new <br />roofs and cost-effective option for extending the life of existing roof systems. <br />Typical Applications: <br />• As a treatment for EPDM (ethylene propylene diene monomer) <br />membranes. <br />• To prepare existing EPDM roof surfaces to receive a RE-ROOF base <br />coat. <br />Advantages: <br />• Nonflammable <br />• Minimum overspray <br />Surface Preparation: <br />• All substrates must be strong, solid, and stable. <br />• All roof drains must be unclogged and working properly. Roofs must be <br />sloped according to industry standards to facilitate water removal. All <br />water must drain and/or evaporate within 48 hours. <br />• Install crickets and complete metal sheet work repairs. Tighten fasteners <br />and replace any fasteners that have deteriorated. <br />• All surfaces must be dry, clean and free from loose sand, dirt, dust and <br />other foreign substances that could interfere with adhesion. <br />• All surfaces containing oil, grease, or similar types of contamination <br />must be thoroughly degreased using a roof cleaner that is appropriate <br />for the substrate. Follow all written instructions for the roof cleaner and <br />completely remove all residue left from the cleaning process. <br />• EPDM (ethylene propylene diene monomer) membranes: <br />Repair all seam and flashing failures. Pressure-wash the <br />existing surface with water to clean and remove all foreign <br />matter, dirt, and debris. <br />Jobsite Preparation: <br />Take all necessary precautions to ensure safety. <br />• Cover all intake vents near the work area. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>RE-ROOF EPDM Treatment <br />Coverage Rate</p> <p>500 ft²/gallon</p> <p>pH</p> <p>6-7</p> <p>Specific Gravity</p> <p>1.01 g/cc</p> <p>Wet Density</p> <p>8.46 lb / gal</p> <p>Color</p> <p>Pink/Purple</p> <p>All data are averages of several tests under laboratory conditions. In practice <br />climatic variations such as temperature, humidity, and porosity of substrate may <br />affect these values.</p> <p>• Provide a spill containment system to contain any potential spills of <br />undiluted RE-ROOF EPDM Treatment. <br />• In preparation for the cleaning and rising process, ensure that there <br />is proper drainage on the roof area. Note: Wash water disposal <br />procedures must be in compliance with local codes and regulations. <br />• Ensure that CO2 or other dry chemical fire extinguishers are within easy <br />access. <br />• Hot surfaces should be cooled and shaded while cold surfaces should <br />be heated and sheltered. <br />Mixing: <br />RE-ROOF EPDM Treatment is packaged ready-to-use. No mixing is <br />required. <br />Application: <br />Read all instructions thoroughly prior to installation. <br />Roof areas can encompass many different types of materials, especially <br />in penetration and transition areas. For this reason, it is likely that several <br />different primers will be required. <br />• Primer (for field areas): Apply RE-ROOF EPDM Treatment over existing <br />EPDM (ethylene propylene diene monomer) membranes in a 3 - 4 ft. arc <br />pattern at a rate of 500 ft²/gallon using an airless sprayer, conventional <br />pressure sprayer, or Hudson-type agricultural sprayer. <br />• Allow RE-ROOF EPDM Treatment to dwell on surface of EPDM for at <br />least 15 min. <br />• Remove RE-ROOF EPDM Treatment from the surface of the EPDM by <br />using a pressure washer (between 2000 - 3500 psi). Pressure washing <br />should be done slowly and close to the surface of the EPDM in order to <br />facilitate the complete removal of RE-ROOF EPDM Treatment and any <br />contaminants. <br />• Perform a thorough and final rinse of the entire surface with water using <br />a pressure washer. Clear-colored rinse water that is free of any bubbles <br />is an indication of an adequate rinsing technique. Allow EPDM surface <br />to dry. <br />• Primer (for flashing areas): Apply the appropriate primer(s) to all areas <br />that will receive a RE-ROOF flashing such as edges, seams, joints, metal <br />Page 1 of 2</p> <p>(updated 12/16/22/EK/AC)</p> <p>RE-ROOF EPDM Treatment <br />flashing, penetrations, and transitions. See primer selection chart for <br />guidance. Refer to the corresponding primer Technical Data Sheet for <br />surface preparation, mixing and application instructions, dry mil thickness <br />requirements, approx. coverage, curing and recoat times. Allow to cure <br />and pay close attention to recoat times. <br />• First Flashing Treatment: Treat edges, seams, joints, metal flashing, <br />penetrations, and transitions with a RE-ROOF flashing. Include drains, <br />fasteners, guide wire straps, gutters, inside and outside corners, <br />joints, machine legs, parapet walls and caps, pipes, protrusions, rake <br />edges, round projections, screws, seams, signposts, skylights, voids, <br />and any areas where water could enter through the roof. Refer to the <br />corresponding RE-ROOF flashing Technical Data Sheet for surface <br />preparation, mixing and application instructions, dry mil thickness <br />requirements, approx. coverage, curing and recoat times. Allow to cure <br />and pay close attention to recoat times. <br />• Second Flashing Treatment: Apply a second coat of a RE-ROOF <br />flashing over all areas that received the first coat of a RE-ROOF flashing. <br />Allow to cure and pay close attention to recoat times. <br />• First Base Coat: Apply the first coat of a RE-ROOF Base Coat. Refer <br />to the corresponding base coat Technical Data Sheet for surface <br />preparation, mixing and application instructions, dry mil thickness <br />requirements, approx. coverage, curing and recoat times. Overlap the <br />RE-ROOF flashing by at least 6 inches (15 cm). <br />Drying: <br />• Allow surface of EPDM to completely dry before proceeding with the <br />application of a RE-ROOF flashing or a RE-ROOF base coat. Drying <br />time will vary, depending on temperature, humidity and air movement. <br />Clean-up: <br />Clean tools and equipment with water immediately after use. <br />Packaging: <br />RE-ROOF EPDM Treatment is packaged in a 5-gallon pail (18.9 liters).</p> <p>Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Ensure adequate ventilation <br />in application area. Use Type C organic vapor cartridge respirators <br />during spray application. Vapor inhalation problems are characterized <br />by coughing, shortening of breath and tightness in the chest. Anyone <br />exhibiting these types of symptoms should be immediately removed from <br />the workplace and administered oxygen or fresh air. If the condition is <br />prolonged or extreme, seek emergency medical assistance immediately. <br />Avoid contact with skin and eyes. Wear fabric coveralls, neoprene gloves <br />or other chemically resistant gloves and safety goggles during mixing and <br />application. After contact with skin, wash with plenty of water. In case of <br />eye contact, rinse immediately with plenty of water for 15 minutes and <br />seek emergency medical assistance immediately. KEEP OUT OF REACH <br />OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Shelf Life & Storage: <br />• 12 months in unopened, original packaging when stored at <br />temperatures between 50°F and 75°F (10°C to 24°C). <br />• Keep containers closed, store in a dry, cool place away from heat, <br />direct sun, sparks, open flame, and moisture. <br />• Protect material from freezing.</p> <p>RE-ROOF Primer Selection Guide <br />PRIMER</p> <p>BUR</p> <p>PRO-Tekt SP</p> <p>Concrete</p> <p>EPDM</p> <p>Galvanized Steel</p> <p>Masonry</p> <p>X</p> <p>X</p> <p>Polyurethane</p> <p>PVC</p> <p>TPO</p> <p>X</p> <p>X</p> <p>X</p> <p>X</p> <p>X</p> <p>RE-R00F EPDM Treatment <br />RE-R00F Primer PO <br />RE-R00F Primer WB</p> <p>PRIMER</p> <p>X</p> <p>Modified Bitumen</p> <p>PRO-Tekt SP</p> <p>Wood (trim only) <br />X</p> <p>RE-R00F EPDM Treatment <br />RE-R00F Primer PO <br />RE-R00F Primer WB</p> <p>X</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 2 of 2 <br />(updated 12/16/22/EK/AC)</p>
