RE-ROOF Silicone Accelerator_122022.pdf
2 Pages
415 KB
Download
<h1>RE-ROOF Silicone Accelerator_122022.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>RE-ROOF Silicone Accelerator <br />Accelerator for RE-ROOF Silicone Coating <br />CSI Div. 07 & 09 <br />07 01 50 Maintenance of Membrane Roofing <br />07 01 50.61 Roof Re-Coating <br />07 14 16 Cold Fluid Applied Waterproofing <br />09 01 90 Maintenance of Painting and Coating</p> <p>Technical Properties: <br />RE-ROOF Silicone Accelerator <br />Mixing Ratio <br />(RE-ROOF Silicone Accelerator to <br />RE-ROOF Silicone Coating)</p> <p>1:80</p> <p>Pot Life at 75ºF (24ºC), <br />50% RH (when mixed with REROOF Silicone Coating)</p> <p>15 - 20 min</p> <p>Molecular Weight</p> <p>200 g/mol</p> <p>Product Description: <br />RE-ROOF Silicone Accelerator is an optional additive for RE-ROOF <br />Silicone Coating to shorten the curing time and permit sooner application <br />of the next layer in the Aquafin RE-ROOF Silicone System. The RE-ROOF <br />System is an eco-friendly, reliable solution for new roofs and cost-effective <br />option for extending the life of existing roof systems.</p> <p>Density</p> <p>8.4 lbs/gal</p> <p>Boiling Point</p> <p>392°F (200°C)</p> <p>Flash Point</p> <p>266°F (130°C)</p> <p>Viscosity at 75°F (24°C)</p> <p>200 cps</p> <p>Color</p> <p>Light Yellow</p> <p>Typical Applications: <br />• Mix with RE-ROOF Silicone Coating</p> <p>VOC, ASTM D-2369-81</p> <p>0 lb/gal, <br />0 gm/liters</p> <p>LEED Points <br />MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Advantages: <br />• Facilitates faster project completion by reducing lag time between coats <br />of RE-ROOF Silicone Coating <br />Surface Preparation: <br />RE-ROOF Silicone Accelerator must be mixed with RE-ROOF Silicone <br />Coating. Refer to the RE-ROOF Silicone Coating Technical Data Sheet for <br />information on surface preparation. <br />• All substrates must be strong, solid, and stable. <br />• All surfaces to receive RE-ROOF Silicone Coating as a base coat <br />require an appropriate Aquafin primer. <br />• All surfaces to receive RE-ROOF Silicone Coating as a top coat require <br />RE-ROOF Silicone Coating as a base coat. <br />• All surfaces, whether primed or base-coated, must be dry, clean and <br />free of dirt, dust, grease, oil, and other foreign substances that could <br />interfere with adhesion. <br />Jobsite Preparation: <br />Take all necessary precautions to ensure safety. <br />• Cover all intake vents near the work area. <br />• Minimize or exclude all personnel not directly involved with the <br />application. <br />• Follow appropriate measures to prevent any sparks. <br />• Do not weld, smoke or allow any open flames during mixing, <br />application or curing. <br />• Ensure that CO2 or other dry chemical fire extinguishers are within easy <br />access. <br />• Hot surfaces should be cooled and shaded while cold surfaces should <br />be heated and sheltered. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>All data are averages of several tests under laboratory conditions. In practice <br />climatic variations such as temperature, humidity, and porosity of substrate may <br />affect these values.</p> <p>Mixing: <br />Mixing with 5 gallon size units of RE-ROOF Silicone Coating: <br />• Condition material to 60°F to 80°F (16°C to 27°C) prior to mixing <br />and application. <br />• Use chemical resistant (Nitrile) gloves and goggles when mixing REROOF Silicone Accelerator. <br />• The volume mixing ratio is 1 Part RE-ROOF Silicone Accelerator to 80 <br />Parts RE-ROOF Silicone Coating or ½-pint (8 oz) RE-ROOF Silicone <br />Accelerator to 5 gallons (640 oz) RE-ROOF Silicone Coating. <br />• Mix in a well ventilated area. <br />• Thoroughly mix RE-ROOF Silicone Coating individually, at slow <br />speeds (not exceeding 500 rpm) to evenly distribute pigments and <br />other ingredients that may have settled until a homogeneous mixture <br />is achieved. Then add RE-ROOF Silicone Accelerator and mix again <br />until homogeneous mixture is achieved. Do not mix in an up and down <br />motion. <br />Note: Do not mix RE-ROOF Silicone Accelerator with 55 gallon size units <br />of RE-ROOF Silicone Coating. <br />Application: <br />Read all instructions thoroughly prior to installation. <br />• Refer to the Technical Data Sheet for RE-ROOF Silicone Coating for all <br />application instructions. <br />Limitations: <br />• Do not dilute under any circumstance. <br />Page 1 of 2</p> <p>(updated 12/20/22/EK/AC)</p> <p>RE-ROOF Silicone Accelerator <br />• Do not mix more material than can be used within 20 minutes. <br />• Large mixed batches, high temperatures, high humidity, and thicker <br />applications will significantly reduce the pot life and significantly <br />accelerate the cure time. <br />• Once containers have been opened, use all material immediately. <br />Clean-up: <br />Clean tools and equipment with an approved solvent immediately after <br />use. Cured material must be removed mechanically. <br />Packaging: <br />RE-ROOF Silicone Accelerator <br />• 1 quart (0.95 liters) can <br />Shelf Life & Storage: <br />• 12 months in unopened, original packaging when stored at <br />temperatures between 40°F and 90°F (4.4°C to 32°C). <br />• Keep containers closed, store in a dry, cool place away from heat, <br />direct sun, sparks, open flame, and moisture. <br />• Protect material from freezing. <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />This product is considered Dangerous Goods. DOT regulations classify it <br />as: UN 1760, CORROSIVE LIQUID N.O.S. (contains Amine), Class 8, <br />PG-111. This product when comes in contact with water, will react violently <br />and can cause a fire. Dispose all waste per applicable regulations <br />Refer to SDS. For commercial use only. Ensure adequate ventilation <br />in application area. Use Type C organic vapor cartridge respirators <br />during spray application. Vapor inhalation problems are characterized <br />by coughing, shortening of breath and tightness in the chest. Anyone <br />exhibiting these types of symptoms should be immediately removed from <br />the workplace and administered oxygen or fresh air. If the condition is <br />prolonged or extreme, seek emergency medical assistance immediately. <br />Avoid contact with skin and eyes. Wear fabric coveralls, neoprene gloves <br />or other chemically resistant gloves and safety goggles during mixing and <br />application. After contact with skin, wash with plenty of water. In case of <br />eye contact, rinse immediately with plenty of water for 15 minutes and <br />seek emergency medical assistance immediately. KEEP OUT OF REACH <br />OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only. <br />Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 2 of 2 <br />(updated 12/20/22/EK/AC)</p>
