TDS-REBAR PRIMER-CI 013122.pdf
2 Pages
59.3 KB
Download
<h1>TDS-REBAR PRIMER-CI 013122.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>REBAR PRIMER/BOND-CI</p> <p>Cementitious corrosion protection and bonding agent <br />CSI Div. 03 <br />03 01 00 Maintenance of Concrete</p> <p>Technical Properties: <br />Physical state</p> <p>Cement powder</p> <p>LEED Points</p> <p>Color</p> <p>Red</p> <p>Components</p> <p>One</p> <p>Bulk density</p> <p>74. 9 lbs/ft³ (1.2 kg/dm³)</p> <p>Working time</p> <p>~60 minutes @ 68°F (20°C)</p> <p>Product Description: <br />REBAR PRIMER/BOND-CI is a one-component, cementitious, anticorrosion coating for protection of steel reinforcement and as a bonding <br />agent for concrete surfaces.</p> <p>Application temperature</p> <p>40°F (5°C) to 95°F (35°C)</p> <p>Typical Applications: <br />• As an anti-corrosion, protective coating for steel rebar in concrete <br />restoration. <br />• As a bonding agent for concrete repair mortars or fresh concrete.</p> <p>Flexural Strength <br />ASTM C 348</p> <p>~1,400 psi @ 28 days <br />(~ 9.7 MPa)</p> <p>Splitting Tensile Strength <br />ASTM C 496</p> <p>~500 psi @ 28 days <br />(~3.5 MPa)</p> <p>Advantages: <br />• Mixes with water only <br />• Extended pot life and contact time <br />• VOC compliant (solvent free) <br />• Resistant to penetration of water and chlorides <br />• Excellent workability with long pot life <br />• Very easy to use even on vertical and overhead areas <br />• Extended open time allowing for repair mortars up to 3 days after <br />application <br />• Can be applied by brush or spray <br />• Active corrosion inhibitor</p> <p>Slant Shear <br />ASTM C 882</p> <p>~2,600 psi @ 28 days <br />(~17.9 MPa)</p> <p>Substrate Preparation: <br />• Before application of REBAR PRIMER/BOND-CI, exposed steel <br />reinforcement must be cleaned by mechanical means. Reinforcement <br />must be dry, dust and grease free. <br />• Concrete surfaces must be clean and free from laitance, dirt, dust and <br />any other bond inhibiting substances. Prepare surface by mechanical <br />means to obtain a surface profile of CSP 5 - CSP 7 per ICRI Guideline <br />No. 310.2-1997, Selecting and Specifying Concrete Surface <br />Preparation for Sealers, Coatings and Polymer Overlays. <br />• Concrete surfaces must be left in a saturated surface dry (SSD) condition <br />immediately prior to the application of REBAR PRIMER/BOND-CI.</p> <p>MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, L ow-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Mixing Ratio: <br />• 10 lb.( 4.5 kg) pail: 1.4 qts. (1.3 L) of water <br />(yield of 0.75 mixed gallon (2.8 L)) <br />Mix REBAR PRIMER/BOND-CI with a suitable drill (max. 300 rpm) and <br />mixing paddle (mixing time approx. 2 – 3 minutes) until a homogenous <br />and lump free consistency is achieved. Allow material to sit approx. 2 <br />minutes then remix 15 – 30 sec. Only mix as much material as can be <br />used within working life of the material (1 hour depending on temperature). <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Physical Properties: The values stated are applicable with ambient temperatures of +23° C and 50% relative air humidity. Higher temperatures shorten <br />the processing time, lower temperatures extend processing times.</p> <p>Yield as a Bonding Agent: <br />~60 ft2/mixed gal. (one coat at 20 mils) (~5.6 m²/3.8 L @ 0.5 mm) <br />Yield on Reinforcing Steel <br />~30 ft2/mixed gal. (two coats at 20 mils each) <br />Bar Size</p> <p>Linear Feet (m) Covered</p> <p>#4</p> <p>230 (70)</p> <p>#5</p> <p>184 (55)</p> <p>#6</p> <p>153 (47)</p> <p>#7</p> <p>131 (40)</p> <p>#8</p> <p>115 (35)</p> <p>Application: <br />Steel reinforcement anti-corrosion coating: <br />Apply REBAR PRIMER/BOND-CI by brush or spray at a thickness of 20 <br />mils (0.5 mm) to properly prepared steel reinforcement. Take care to <br />properly coat the underside of the exposed steel. Apply the second coat, <br />at the same rate, after the first coat has dried (approx. 2 hours). Place <br />repair mortar after primer has dried and within 7 days of application. <br />Concrete bonding agent: <br />Apply REBAR PRIMER/BOND-CI by brush or spray at a thickness of 20 <br />mils (0.5 mm) to a properly prepared and SSD concrete surface. <br />Application of repair mortar or fresh concrete is best while the REBAR <br />PRIMER/BOND-CI is wet. Place repair mortar or fresh concrete <br />immediately after application of bonding agent, or after it has dried (2 to 4 <br />hours), but within 3 days of application.</p> <p>Page 1 of 2</p> <p>(updated 01/31/22 EB,VB)</p> <p>AQUAFIN® REBAR PRIMER/BOND-CI <br />Clean-up: <br />Thoroughly clean tools with water (before material hardens). <br />Shelf Life: <br />12 months when stored dry in the original unopened packaging. <br />Packaging: <br />22 lb (10 kg) pails (yield of ~1.65 mixed gallons (~6.3 L)) <br />Limitations: <br />• Ensure that the substrate and ambient temperatures are between 40°F <br />(5°C) and 90°F (32°C). <br />• Minimum thickness for corrosion protection is 40 mils (1.0 mm). <br />• Minimum thickness for bonding agent is 20 mils (0.5 mm). <br />• Pre-condition material to 70°F (21°C) for 24 hours before using. <br />• Protect from freezing for 24 hours after application. <br />• Cover treated areas with suitable sheeting to protect against rain <br />contamination with bond-breaking substances (i.e. construction dust), and <br />corrosion causing salts (i.e. ocean air). <br />• If material is exposed to the elements, the surface must be cleaned with <br />water prior to the placement of mortar or concrete. <br />• Areas not being treated are to be protected from the effects of REBAR <br />PRIMER/BOND-CI. <br />• Do not re-temper.</p> <p>Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Health & Safety: <br />Refer to SDS. KEEP OUT OF REACH OF CHILDREN. <br />REBAR PRIMER/BOND-CI contains cement that forms an alkaline reaction <br />with moisture. Therefore contact with the eyes and skin is to be avoided <br />and mortar splashes are to be thoroughly washed off immediately with <br />plenty of water. On contact with the eyes, seek medical attention from an <br />eye specialist. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year from <br />the date of installation to be manufactured free of defects and to be consistent with its technical <br />properties as stated in our current Technical Data Sheet. This product must be used as directed <br />and within its stated shelf life. AQUAFIN INC. will replace or at our discretion refund the purchase <br />price of any product, excluding cost of labor, which is proven to be defective. Our product <br />recommendations are based on industry standards and testing procedures. It is the buyer’s <br />obligation to test the suitability of the product for an intended use prior to using it. We assume no <br />warranties written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR FITNESS <br />FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES <br />EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort including <br />remote or consequential damages, down time, or delay. Any claim for a defective product must <br />be filed within 30 days of discovery of a problem, and must be submitted with written proof of <br />purchase.</p> <p>For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(updated 01/31/22 EB,VB)</p>
