Safety Data Sheet (SDS)
Page 1/6
OSHA HazCom Standard 29 CFR 1910.1200(g) and GHS Rev 03.
Printing date 08/18/2022
Reviewed on 08/18/2022
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
IDENTITY:
Product Name: EPOXY-Gel COMPONENT B Product Use Description: Epoxy Resin Adhesive, For Further Information, Refer to the Product Technical
Data Sheet
AQUAFIN, INC. 505 BLUE BALL RD. #160 ELKTON, MD 21921
24 hr Emergency Phone: Chem-Tel (800) 255-3924 Information Phone No: (410) 392-2300
info@aquafin.net
www.aquafin.net
SECTION 2: HAZARDS IDENTIFICATION GHS Hazard:
ROUTES OF ENTRY: SIGNAL WORD:
EYE:
YES
SKIN:
INGESTION:
INHALATION:
DANGER!
PHYSICAL HAZARDS: Not Classified HEALTH HAZARDS: (ACUTE AND CHRONIC) Serious eye damage Cat. 1 EYES: Skin Corrosion Cat. 1B SKIN: Skin Irritation Cat. 2 Skin Sensitization Cat.1 Reproductive Toxicity Cat.1B Specific target organ toxicity- single exposure Cat.3 Acute Inhalation Toxicity Cat. 4 INHALATION: Specific target organ toxicity- single exposure Cat.3 CARCINOGEN: Carbon Black IARC 2B ENVIRONMENTAL HAZARDS: Acute aquatic toxicity Cat.2 Chronic aquatic toxicity Cat.2 INGESTION:
HAZARD STATEMENTS:
H302+H312+H332 – Harmful if swallowed, inhaled or in contact with skin. H314 - Causes severe skin burns and eye damage. H315 – Causes serious eye damage. H317 - May cause an allergic skin reaction H318 - Causes serious eye damage. H330 – Fatal if inhaled. H335 – May cause respiratory irritation. H361 – Suspected of damaging fertility or the unborn child. H412 – Harmful to aquatic life with long lasting effects.
PRECAUTIONARY STATEMENTS: P261 – Avoid breathing dust/fume/gas/mist/vapors/spray. P262 - Do not get in eyes, on skin, or on clothing P264 - Wash…thoroughly after handling with soap and water. P270 – Use outdoors or in a well-ventilated area. P272 – Contaminated work clothing should not be allowed out of the workplace. P273 – Avoid release to the environment. P280 - Wear Protective gloves/protective clothing/eye protection/face protection. P301+P330+P331 – IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. P302+P352 – IF ON SKIN: Wash with plenty of soap and water. P303+P361+P353 – IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing. Rinse skin with water/shower. P304+P340+P310 – IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable For breathing. Immediately call a POISON CENTER or doctor/physician. P305+P351+P338 - IF IN EYES Rinse cautiously with water for several minutes. Remove contact lenses, If present and easy to do. Continue rinsing. P310 – Immediately call a POISON CENTER or doctor/physician. P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
SDS EPOXY-Gel Comp B SDS DATE: 22-AUG-18
Page 1 of 6
EPOXY-Gel, Component B
Safety Data Sheet
P362 – Tale off contaminated clothing and wash before reuse. P403+P233 – Store in a well-ventilated place. Keep container tightly closed. P405 - Store locked up. P501 -Dispose of contents/container to an approved waste disposal plant.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Persons with preexisting skin or respiratory disorders may have their conditions aggravated by over exposure to this material. This product is not for use in an aerosol or spray.This product contains a component that is toxic by inhalation when aerosolized or sprayed. Refer to Section 11 of the SDS for toxicity information. Review the toxicity information against your intended use. If product is not being aerosolized or sprayed, inhalation toxicity is not applicable. SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
CAS #:
CAL-OSHA PEL TWA (8hours)
ACGIH TLV TWA (8 hours)
Other Limits RECOMMENDED
% BY WEIGHT
HAZARDOUS COMPONENTS Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)-
64852-22-8
No Data
4
Tofa, reaction products with TEPA
68953-36-6
>17
Tetraethylenepentamine
112-57-2
4-tert-Butylphenol
98-54-4
<6
Diethylenetriamine
111-40-0
<2
Benzyl Alcohol
100-51-6
Tris-2,4,6-(dimethylaminomethyl)phenol
90-72-2
<3
Bis(dimethylaminomethyl)phenol
71074-89-0
<0.5
Treated fumed silica
67762-90-7
<4
Carbon Black
1333-86-4
TWA WEEL 1ppm(5mg/m3)
TWA WEEL 10ppm(44mg/m3)
1.3
SECTION 4: FIRST AID MEASURES EYES: SKIN: INGESTION: INHALATION:
Immediately flush eyes with water for a minimum of 15 minutes while holding eyes open. Remove contact lenses if present and easy to do. If redness, burning, blurred vision, or swelling persists, consult a physician. Remove contaminated clothing and product. Immediately wash affected area with soap and water. Do not apply greases or ointments. If skin irritation persists, consult a physician. Rinse mouth immediately. Give small amounts of water, only if person is conscious. Only induce vomiting at the instruction of medical personnel. consult a physician Remove patient to fresh air. Give oxygen or artificial respiration if needed. If patient continues to experience difficulty breathing, consult a physician.
SECTION 5: FIRE-FIGHTING MEASURES SUITABLE EXTINGUISHING MEDIA: SPECIAL FIRE FIGHTING PROCEDURES:
HAZARDOUS DECOMPOSITION PRODUCTS:
FLASH POINT: METHOD USED:
Extinguish with foam, carbon dioxide, dry powder, or water fog. Use standard fire-fighting procedures and consider the hazards of other involved materials. In case of a fire and / or explosion do not breathe fumes. Self-contained breathing apparatus and full protective clothing must be worn. Move containers from fire area if you can do so without risk. Cool containers with flooding quantities of water until well after fire is out. Prevent runoff from fire control or dilution from entering streams, sewers, or drinking water supply. Hazardous decomposition products may occur when material polymerizes at temperatures above 500 oF (260 oC). Irritating and toxic gases/fumes may be released during a fire. Do not allow run-off from fire-fighting to enter drains or water courses.
210 oF / 99 oC PMCC
SECTION 6: ACCIDENTAL RELEASE MEASURES PERSONAL PROTECTION:
Keep unnecessary personnel away. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Wear appropriate personal protective equipment. Do not touch containers or spilled material unless wearing appropriate protective clothing. Avoid inhalation of vapors or mists. Ensure adequate ventilation. Local authorities should be
Page 2 of 6
ACCIDENTAL RELEASE MEASURES: WASTE DISPOSAL:
advised if significant spillage cannot be contained. In case of spill, clean up using absorbent material such as earth or sand. Small quantities can be wiped up with cloth, place cloth in leak proof container and dispose of properly. Observe Federal, State and local regulations covering chemical waste spills.
SECTION 7: HANDLING AND STORAGE Use personal protective equipment to ensure product does not contact eyes or skin when handling materials. Store in cool dry place out of direct sun rays. Keep from freezing. Recommend storage temperatures range: between 40o and 95 oF (4o - 35 oC)
PERSONAL PROTECTION: HANDLING AND STORAGE:
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION PROTECTIVE MEASURE: EYE PROTECTION: HAND PROTECTION: SKIN AND BODY PROTECTION: RESPIRATORY PROTECTION: WORK HYGIENIC PRACTICES: ENGINEERING CONTROLS:
Wear appropriate personal protective equipment. Wear appropriate safety glasses with side shields, goggles or full face shield. When working on an overhead application a full face shield is recommended. Wear chemical-resistant gloves such as: Nitrile, neoprene, butyl. Wear long sleeve shirts/long pants and other clothing as required to minimize contact. Do not breathe gas/fumes/vapor/ or spray. The use of a respirator is not required during general use of this product provided adequate ventilation. If grinding or cutting cured product the use of an approved respirator is recommended. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. When using indoors, good ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. Ready access to running water is required. Provide eyewash station.
EXPOSURE LIMITS Component Poly[oxy(methyl-1,2-ethanediyl)],.alpha.’,.alpha.”1,2,3-propanetriyltris[.omega.-(2aminomethylethoxy)64852-22-8 Tofa, reaction products with TEPA 68953-36-6
OSHA (PEL)
ACGIH (TLV)
NIOSH (Pocket Guide)
4-tert-Butylphenol 98-54-4
Diethylenetriamine 111-40-0
1 ppm(4mg/m3)
1 ppm (4mg/m3) skin
Benzyl Alcohol 100-51-6
Tris-2,4,6-(dimethylaminomethyl)phenol 90-72-2 Bis(dimethylaminomethyl)phenol 71074-89-0
3.5 mg/m3
TWA 3 mg/m3
TWA 3.5 mg/m3
Carbon Black 1333-86-4 SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE: ODOR: PHYSICAL STATE: pH AS SUPPLIED: BOILING POINT: MELTING POINT: FREEZING POINT: VAPOR PRESSURE: VAPOR DENSITY (AIR = 1): SPECIFIC GRAVITY (H2O = 1): EVAPORATION RATE: SOLUBILITY IN WATER: PERCENT SOLIDS BY WEIGHT: PERCENT VOLATILE: VOLATILE ORGANIC COMPOUNDS (VOC): MOLECULAR WEIGHT:
Black Ammonia Paste basic N/D N/D N/D <1mm @ 20C Heavier than air 0.95 N/D Slight N/D N/D ND ND
Page 3 of 6
EPOXY-Gel, Component B Safety Data Sheet
6400 p.
VISCOSITY: SECTION 10: STABILITY AND REACTIVITY STABILITY: CONDITIONS TO AVOID (STABILITY): INCOMPATIBILITY (MATERIAL TO AVOID): HAZARDOUS DECOMPOSITION OR BYPRODUCTS: HAZARDOUS POLYMERIZATION:
Stable Exposure to excessive heat and open flame Strong acids, peroxides and other oxidizing agents. Normal combustion forms carbon dioxide, carbon monoxide, oxides o carbon and other organic compounds, Will not occur
SECTION 11: TOXICOLOGICAL INFORMATION Toxicity Acute Oral Toxicity: Oral-Components Carbon Black Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)-
CAS#
1333-86-4 64852-22-8
LD50 15,400 mg/kg Species: Rat Acute toxicity estimate: 2,690 mg/kg
Tris-2,4,6-(dimethylaminomethyl)phenol Acute Dermal Toxicity: Dermal-Components Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)Acute Inhalation Toxicity Inhalation-Components Diethylenetriamine Benzyl Alcohol Skin Corrosion/ Irritation: Corrosion/Irritation Components Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)-
LD50 2,169 mg/kg Species: Rat M/F
No data available on the product itself
No data available on the product itself 64852-22-8
LD50 12,500 mg/kg Species: Rabbit
No data available on the product itself 111-40-0 100-51-6
LC50(4hr): >0.07-<0.3 Species: Rat LC50(4hr): >4.178 mg/l Species: Rat Skin corrosion
Extremely corrosive and destructive to tissue.
Tris-2,4,6-(dimethylaminomethyl)phenol Eye Damage/Irritation: Damage/Irritation Components Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)-
Corrosive (4hr) Species: Rabbit.
May cause irreversible eye damage.
Tris-2,4,6-(dimethylaminomethyl)phenol Respiratory Damage/Irritation: Damage/irritation Components Sensitization:
Corrosive Species: Rabbit.
Tris-2,4,6-(dimethylaminomethyl)phenol Germ Cell Mutagenicity
Severe eye damage
The product or a component may be mutagenic, the data is inconclusive. No data available on the product itself
Maternal Toxicity: Carcinogenicity: Classification ACGIH: IARC: NTP OSHA
May cause sensitization by inhalation or skin contact Skin sensitizer , sub. cat. 1B
Not Classified Carbon Black IARC Carcinogen 2B Not Listed Not Classified
SECTION 12: ECOLOGICAL INFORMATION
Page 4 of 6
ECOTOXICITY: Aquatic toxicity: Toxicity to Fish-Components Benzyl Alcohol Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)-
100-51-6 64852-22-8
LC50(96hr) 460 mg/l Species: Fathead minnow LC50(96hr) 68 mg/l
Tris-2,4,6-(dimethylaminomethyl)phenol Toxicity to algae-Components Benzyl Alcohol
LC50(96hr) 175 mg/l Species: Cyprinus carpio
100-51-6 90-72-2
IC50(72hr): 700 mg/l Species: Algae EC50(72hr): 84 mg/l Species: Desmodesmus subspicatus.
EC50(48hr): 37.5 mg/l Species: Water flea
Tris-2,4,6-(dimethylaminomethyl)phenol Toxicity-AquaticInvertabrates Carbon Black Toxicity to other organisms: PERSISTENCE & DEGRADABILITY: BIODEGRADABILITY: Biodegradability-Components Poly[oxy(methyl-1,2ethanediyl)],.alpha.’,.alpha.”-1,2,3propanetriyltris[.omega.-(2aminomethylethoxy)Tris-2,4,6-(dimethylaminomethyl)phenol BIOACCUMULATIVE POTENTIAL: BioAccumulaive-Components: MOBILITY IN SOIL: OTHER ADVERSE EFFECTS: AQUATIC RELEASE:
No data available on product itself 64852-22-8
Not readily biodegradable <5% 28d
Not readily biodegradable 4% 28d No data available on product itself NDA NDA Advise authorities if product has entered or may enter watercourses or sewer drains.
SECTION 13: DISPOSAL CONSIDERATIONS WASTE DISPOSAL METHOD:
Do not allow this material to drain into sewers / waterways, ditches, containment pools or water supplies. Dispose of contents / containers in accordance with local/regional/international regulations.
SECTION 14: TRANSPORT INFORMATION U.S. DEPARTMENT OF TRANSPORTATION Amines, liquid, corrosive, n.o.s. (Polyamidoamine, Tetraethylenepentamine) PROPER SHIPPING NAME: 8 HAZARD CLASS: UN2735 ID NUMBER: III PACKING GROUP: WATER TRANSPORTATION PROPER SHIPPING NAME: HAZARD CLASS: ID NUMBER: PACKING GROUP:
Amines, liquid, corrosive, n.o.s. (Polyamidoamine, Tetraethylenepentamine), Marine Pollutant 8 UN2735 III
AIR TRANSPORTATION PROPER SHIPPING NAME: HAZARD CLASS: ID NUMBER: PACKING GROUP:
Page 5 of 6
SECTION 15: REGULATORY INFORMATION U.S. FEDERAL REGULATIONS TSCA (TOXIC SUBSTANCE CONTROL ACT): CERCLA (COMPREHENSIVE RESPONSE COMPENSATION, AND LIABILITY ACT): OSHA: WHMIS
xxxxxxxxxx 29 CFR 1910.1200 (Hazard Communication required) XXXXXXXXXX
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT): XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 302/304 Acute Health Hazard: Yes 311/312 HAZARD CATEGORIES: Chronic Health Hazard: Yes Fire Hazard: No Pressure Release Hazard: No Reactivity Hazard: No Xxxxxxxxxx 313 REPORTABLE INGREDIENTS: STATE REGULATIONS: CALIFORNIA PROPOSITION 65 (THE SAFE DRINKING WATER AND TOXICS ENFORCEMENT ACT of 1986)
This product does not contain known levels of any chemicals known to cause cancer or reproductive harm. SECTION 16: OTHER INFORMATION HAZARDOUS MATERIALS IDENTIFICATION SYSTEM HMIS HAZARD RATING HEALTH 2 FLAMMABILITY 1 REACTIVITY 1 PERSONAL PROTECTION C 4 – Severe, 3 – Serious, 2 – Moderate, 1 - Slight C – (Safety glasses, gloves, apron) The information provided herein was believed by Aquafin Inc. to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of product and to determine the suitability of the product for its intended use.
Page 6 of 6